Eiki Eip-1000t Dlp Projector Owners Manual
Have a look at the manual Eiki Eip-1000t Dlp Projector Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 422 Eiki manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
28 Turning the Projector On/Off Remove the lens cap and press oSTANDBY-ON on the projector or fON on the remote control. •About the Lamp Indicator The lamp indicator illuminates to indicate the status of the lamp. Red: The lamp is on. Blinking in red:The lamp is warming up or shutting down. Green:The lamp is shut down abnor- mally or the lamp should be re- placed. • When switching on the projector, a slight flick- ering of the image may be experienced within the first minute after the lamp has been illumi- nated. This is normal operation as the lamp’s control circuitry is stabilising the lamp output characteristics. It should not be regarded as faulty operation. • If the projector is put into standby mode and immediately turned on again, the lamp may take some time to start projection.STANDBY-ON buttonNote Lamp indicator • English is the factory default language. If you want to change the on-screen display to another language, change the language according to the procedure on page 43. Info Turning the Projector on Note that the connections to external equip- ment and power outlet should be done be- fore performing the operations written be- low. (See pages 23 to 28.) Power indicator ON button AC socket Power cordSupplied accessory Connecting the Power Cord Plug the supplied power cord into the AC socket on the rear of the projector. EIP-1000T_EN_h05.7.13, 11:56 AM 28
29 On-screen Display (confirmation message) 1 2 Turning the Power off (Putting the Projector into Standby Mode) Press oSTANDBY-ON on the pro- jector or eSTANDBY on the re- mote control, then press that but- ton again while the confirmation message is displayed, to put the projector into standby mode. Unplug the power cord from the AC outlet after the cooling fan stops. • The power indicator on the projector blinks in red while cooling. • The power indicator changes to green when the projector finishes cooling. • Do not unplug the power cord during projection or cooling fan operation. This can cause dam- age due to rise in internal temperature, as the cooling fan also stops. InfoR STANDBY button Locking the Operation Buttons on the Projector (Keylock Function) a Taking the Keylock offHold down p ENTER on the projector for about 5 seconds. a Locking the Operation ButtonsHold down p ENTER on the projector for about 5 seconds while the projector is being turned on. • The keylock function does not affect the op- eration with the remote control buttons. • You cannot use the keylock function while the projector is warming up. • When the projector is in standby mode, you can release the keylock by holding down p ENTER and o STANDBY-ON on the projec- tor simultaneously for about 5 seconds. • Keylock does not function while the projector is: displaying “Menu” screens, in standby mode, warming up, changing input signals, operating “Auto Sync” function, or in “Freeze” mode. Info ROn-screen Display ROn-screen Display Use this function to lock the operation buttons on the projector. EIP-1000T_EN_h05.7.13, 11:57 AM 29
30 1 Adjusting the Focus You can adjust the focus with the focus ring on the projector. Image Projection Rotate the focus ring to adjust the fo- cus while watching the projected image. Focus ring Adjusting the Projected Image 2 Adjusting the Screen Size You can adjust the screen size using the zoom ring on the projector. Rotate the zoom ring to enlarge or shrink the screen size. Zoom ring Switching the Input Mode PressCINPUT 1, CINPUT 2, DINPUT 3 or EINPUT 4 on the remote control to select the input mode. • When pressing INPUT (P/R) on the projector, input mode switches in the following order: INPUT1 INPUT2 INPUT3 INPUT4 • When “Auto Search” is set to “On”, INPUT (P/ R) on the projector functions as the Auto Search buttons. (See page 44.) Select the appropriate input mode for the connected equipment. INPUT buttons EIP-1000T_EN_h05.7.13, 11:57 AM 30
31 3 Adjusting the Height The height of the projector can be ad- justed using the adjustment feet at the front and rear of the projector. When the screen is above the projec- tor, the projection image can be made higher by adjusting the projector. 1 2 3 • Do not apply too much pressure on the pro- jector when the front adjustment foot comes out. • When lowering the projector, be careful not to get your fingers caught in the area between the adjustment foot and the projector. • Hold the projector firmly while lifting or carry- ing. • Do not hold by the lens area. Use the rear adjustment foot to make the projector level. • The projector is adjustable ±1 degree from the standard position. Remove your hands from the HEIGHT ADJUST lever of the pro- jector after its height has been finely adjusted. • The angle of projection is adjustable up to 8 degrees from the surface on which the projector is placed. Lift the projector to adjust its height while lifting the HEIGHT ADJUST lever.HEIGHT ADJUST lever Info Rear adjustment foot • When adjusting the height of the projector, trapezoidal distortion occurs. Follow the pro- cedures in Keystone Correction to correct the distortion. (See pages 33 and 43.) Note Make small adjustments. EIP-1000T_EN_h05.7.13, 11:57 AM 31
32 Image Projection (Continued) Displaying the Black Screen and Turning off the Sound Temporarily Adjusting the Volume Press K/L on the remote control or –O/Q+ on the projector to adjust the vol- ume. • Pressing K/–O will lower the volume. • Pressing L/Q+ will raise the volume. • When the projector is connected to external equipment, the volume level of the external equipment changes in accordance with the volume level of the projector. Set the projector’s volume to the lowest level when turning the projector on/off or changing the input signal. • When you do not want to output the sound from the projector’s speaker while the projector is connected to external equipment, set “Speaker” in “PRJ-ADJ” menu to “Off”. (See page 45.) Press MAV MUTE on the remote con- trol to temporarily display a black screen and turn off the sound. • Pressing MAV MUTE again will turn the projected image back on. On-screen Display Note Note On-screen Display Volume buttons AV MUTE button EIP-1000T_EN_h05.7.13, 11:57 AM 32
33 0 KeystoneADJ. END Correcting Trapezoidal Distortion When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction. • The Keystone Correction can be adjusted up to an angle of approximately ±13 degrees and the screen can also be set up to an angle of approximately ±13 degrees (when the resize mode is set to “STRETCH” (see page 34)). Note 1 2 3 Press g KEYSTONE.• The on-screen display of the Keystone Correction mode will disappear. • You can also use q KEYSTONE on the projector. Press P/Q or O/R to adjust the Keystone Correction. • You can also adjust the Keystone Cor- rection using the adjustment buttons on the projector. Press g KEYSTONE to enter the Keystone Correction mode. • You can also display the on-screen dis- play of the Keystone Correction mode with q KEYSTONE on the projector. • Press l RETURN while the on-screen dis- play of the Keystone Correction mode is on the screen to return to the default setting. Note KEYSTONE button Adjustment buttons (P/R/O/Q) RETURN button ROn-screen display (Keystone Correction mode) Shrinks upper side. (Move the slide bar in the + direction.) Shrinks lower side. (Move the slide bar in the - direction.) • While adjusting the image using Keystone Correction, straight lines and the edges of the image may appear jagged. Info EIP-1000T_EN_h05.7.13, 11:57 AM 33
34 Image Projection (Continued) Resize Mode This function allows you to modify or customize the resize mode to enhance the input image. De- pending on the input signal, you can choose “STRETCH”, “SIDE BAR” or “CINEMA ZOOM” image. Press HRESIZE.• See page 43 for setting on menu screen.RESIZE button VIDEO • “STRETCH” is fixed when 540P, 720P or 1080I signals are entered. : Cutout area on which images cannot be projected.Input Signal DVD / Video Image typeOutput screen image STRETCH SIDE BAR 480I, 480P, 576I, 576P, NTSC, PAL, SECAM 540P, 720P, 1080I 4:3 aspect ratio Letter box Squeezed 16:9 aspect ratio 16:9 aspect ratio CINEMA ZOOM EIP-1000T_EN_h05.7.13, 11:58 AM 34
35 : Cutout area on which images cannot be projected. Computer Input Signal STRETCHOutput screen image Computer Image type SIDE BAR SXGA (1280K1024) Resolution lower than SVGA SVGA Resolution higher than SVGA 1280K720 4:3 aspect ratio 5:4 aspect ratio 16:9 aspect ratio SVGA (800 K 600) XGA (1024 K 768) SXGA (1280 K 960) SXGA L (1400 K 1050)SXGA (1280 K 1024)1280 K 720 640 K 480 J 854 K 480 854 K 480640 K 480 854 K 480 STRETCH SIDE BAR Other aspect ratios4:3 aspect ratio CINEMA ZOOM EIP-1000T_EN_h05.7.13, 11:58 AM 35
36 Operating with the Remote Control Freezing a Moving Image Press NFREEZE.• The projected image is frozen. Press NFREEZE again to return to the moving image from the cur- rently connected device. 1 2 Selecting the Picture Mode Press GPICTURE MODE.• When pressing GPICTURE MODE, the picture mode changes in the following order: Standard Natural Dynamic Movie1 Movie2 You can select the appropriate picture mode to best match the projected im- age you are watching. • See page 41 for details on the picture mode. Note FREEZE button AUTO SYNC button PICTURE MODE button Auto Sync (Auto Sync Adjustment) • When the optimum image cannot be achieved with Auto Sync adjustment, use the help menu for manual adjustments. (See page 46.) Auto Sync function works when detect- ing input signal after the projector turns on. Press FAUTO SYNC to manually ad- just with Auto Sync function. Note EIP-1000T_EN_i 05.8.31, 9:04 AM 36
37 The following shows the items that can be set in the projector. Menu Items “Screen adjustment (SCR-ADJ)” menu INPUT 1 (RGB)/INPUT2 (RGB) “Picture” menu Picture Picture Mode Contrast 0 0 0 0K 7500SCR - ADJ PRJ - ADJ Help BrightRedBlue 1CLR TempBright Boost Lamp Setting Standard Bright Reset SEL./ADJ. ENTER END Picture Resize 0 SCR - ADJ PRJ - ADJ Help Keystone OSD Display Background PRJ Mode Language Front English Logo On Stretch SEL./ADJ. ENTER END Main menu Sub menuPicture Page 41 +30 -30Contrast +30 -30 +30 -30 +30 -30 +30 -30 +30 -30+30 -30 Tint Color Sharp Bright Red Blue *1*2 *1 *1 *3 *3 Progressive Lamp Setting *1 Reset 5500K 6500K 7500K 8500K 9300K 10500K 2D Progressive 3D Progressive Film Mode Bright Eco + Quiet CLR Temp Bright Boost [0/1/2] Page 41 Page 42 Page 42 Page 42 Page 42 Page 42 Standard Natural Dynamic Movie1 Movie2 Picture Mode Main menu Sub menuSCR - ADJ Page 43 Language Resize Page 43 Page 43 Page 43 Page 43 Page 43 Page 43 Keystone OSD Display [On/Off] Background PRJ Mode Stretch Side Bar Cinema Zoom Logo Blue None Front Ceiling + Front Rear Ceiling + Rear English Deutsch Español Nederlands Français Italiano Svenska Português +100 -100 *1 Items when inputting component signal through INPUT 1 or INPUT 2, or when selecting INPUT 3 or INPUT 4. * 2 “Tone” will appear on the menu screen only when PAL or SECAM signals are input (including when forcibly changed to those input signals). There is basically no need to adjust “Tone”, but you can adjust the picture tone with this adjustment when inputting PAL or SECAM signals. * 3 Items when inputting RGB signal through INPUT 1 or INPUT 2. • You can adjust the menu items with icons ( , , and ) using the respective buttons on the re- mote control. INPUT 1 (Component)/INPUT 2 (Component)/INPUT 3/INPUT 4 Picture Picture Mode Contrast 0 0 0 0 K 7500SCR - ADJ PRJ - ADJ Help BrightColorTint0 Sharp 1CLR TempBright Boost Progressive 3D Progressive Standard Reset SEL./ADJ. ENTER END Lamp Setting Bright EIP-1000T_EN_i 05.8.31, 9:05 AM 37