Eiki Efd 52 Owners Manual

							19
Controlling the monitor by a computer
When the RS-232C terminal on the monitor is connected to the RS-232C serial terminal on the computer, 
or when the LAN terminal on the monitor is connected to the LAN terminal on the computer, the computer 
can be used to control the monitor. Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for 
details.
„ When connecting to a computer using an RS-232C serial control cable
To RS-232C terminal
To RS-232C terminal
RS-232C serial control cable
(cross type, commercially available)
ComputerRear view
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the owner’s manual of the 
computer for details.
• Refer to “SETUP MANUAL” contained on the supplied CD-ROM for the RS-232C specifi cations and commands.
• Do not connect the RS-232C cable to a terminal other than the RS-232C terminal on the computer. This may damage your 
computer or monitor.
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This may damage your 
computer.
Note
„ When connecting to the LAN terminal using a LAN cable
* To ensure safety, do not 
connect the LAN terminal 
with any cables such as 
a telephone line that may 
cause excessive voltage.
Hub or computerRear view
To LAN terminal To LAN terminalLAN cable
(supplied)
Ferrite core
WARNING• When connecting to the LAN terminal, be sure to use the LAN cable supplied with this monitor.
• As shown in the illustration above, connect the supplied LAN cable in the way that the ferrite core attached to the cable is 
placed closer to the LAN terminal of the monitor.
• If using LAN cables other than the supplied LAN cable, this monitor may not function properly. (In accordance with FCC 
regulations, this cable is supplied as a LAN cable for use with this monitor.)
Connecting Peripheral Equipment
 
						

							20
Connecting the Power Cord
Caution
•  Do not use a power cord other than the one 
supplied with the monitor.
Be sure to use a power outlet of 
AC 100-240 V, 50/60 Hz.
Using power supply other than the 
one specifi ed may cause fi re.
•  Place the monitor close to the AC outlet, and 
keep the power plug within reach.
•  This product must only be connected to an AC 
100-240 V, 50/60 Hz, grounded (3-prong) outlet. 
Connecting it to any other kind of outlet will 
damage the product and invalidate the warranty.
1  Plug the power cord (supplied) into the AC input 
terminal.
2  Plug the power cord (supplied) into the AC power 
outlet.
Binding Cables
Hole
for
the
power 
cord
clamp
Fastened 
partBand
Power 
cord
clamp12 3
„ Attaching the cable clamp
The cables connected to the terminals on the back 
of the monitor can be neatly bundled using the 
supplied cable clamp as shown in the illustration.
• A cable clamp cannot be easily removed once it is 
attached.
Note
„ Fastening the power cord
The power cord can be fastened using the supplied 
power cord clamp. This will prevent the power cord 
from being disconnected accidentally.
1  Attach the supplied power cord clamp to the 
power cord, making sure the power cord clamp is 
circular hole-side down.
2  Insert the tip of the band into the hole for the 
power cord clamp.
3  While holding the tail of the band, slide the 
fastened part toward the AC input terminal.
 
						

							21
Preparing the Remote Control
Installing the batteries
1Pull down the tab on the cover 
and remove the cover towards 
the direction of the arrow.2Insert the batteries.
•  Insert the batteries making sure 
the polarities correctly match 
the
+
  and -
  marks inside the 
battery compartment.
3Insert the lower tab of the 
cover into the opening, and 
lower the cover until it clicks in 
place.
Incorrect use of the batteries may cause them to leak or explode. Please follow the 
precautions below.
Caution•  Danger of explosion if battery is incorrectly replaced.
  Replace only with alkaline or manganese batteries.
•  Insert the batteries making sure the polarities correctly match the 
+
  and -
   marks inside the battery compartment.
•  Batteries of different types have different properties, therefore do not mix batteries of different types.
•  Do not mix new and old batteries.
  This may shorten the life of new batteries or may cause old batteries to leak.
•  Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.
 Battery fl uid from leaked batteries is harmful to skin, therefore ensure you wipe them fi rst and then remove them using a cloth.
• The batteries included with this monitor may run down in a short period, depending on how they are kept. Be sure to replace them
as soon as possible with new batteries.
•  Remove the batteries from the remote control if you will not be using the remote control for a long time.
•  Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
Remote control operation range
The operation range of the remote control is approx. 
16.4 feet (5 m) at an angle of approx 30° from the 
center to the top/bottom/right/left of the remote 
control sensor.
• Do not expose the remote control to shock by dropping or 
stepping on it. This could lead to a malfunction.
• Do not expose the remote control to liquids, and do not 
place it in an area with high humidity.
• The remote control may not work properly if the remote 
control sensor is under direct sunlight or strong lighting.
• Objects between the remote control and the remote control 
sensor may prevent proper operation.
• Replace the batteries when they run low as this may 
shorten the remote control’s operation range.
• If a fl uorescent light is illuminated near the remote control, 
it may interfere with proper operation.
• Do not use it with the remote control of other equipment 
such as air conditioner, stereo components, etc.
Note
Remote control 
sensor
30° 30°
30°
30°16.4 feet (5 m)
 
						

							22
Turning the Monitor On/Off
Turning on the power
PressPOWER on the monitor.
•  POWER indicator (Red): The monitor is on.
•  After turning the power “ON” by pressing POWER
on the monitor, you can turn the power ON by 
pressingON on the remote control.
POWER button
POWER indicator
Caution
•  When switching the POWER, ON or STANDBY 
buttons off and back on, always wait for at least 
5 seconds. A short interval may result in a 
malfunction.
Turning off the power
ON buttonSTANDBY
button
PressSTANDBY on the remote control.
•  The monitor enters standby mode.
•  The POWER indicator on the monitor changes 
from red to green.
PressPOWER on the monitor.
•  The POWER indicator on the monitor turns off.
•  When the monitor is turned off by POWER on 
the monitor, you cannot turn on the power by 
pressingON on the remote control.
POWER indicator
Lighting (Red) Power ON 
Lighting (Green) Standby
Lights off Power OFF
Flashing
(Orange)When “Power On Delay” function 
is activated.
Flashing (Red) Input signal standby (when 
“Power Management” is set to 
“Mode2” in the Power Control 
menu.)
• If you are not going to use this monitor for a long period 
of time, be sure to remove the power cord from the AC 
outlet.
• Minor power is consumed when the unit is in standby 
mode.
Note
 
						

							23
COMPUTER (1/2), DVI, HDMI, 
S-VIDEO, VIDEO buttons
AV MUTE button
VOL (Volume) buttons (+/-)
Operating with the Remote Control
Switching the input mode
Select the appropriate input mode for the connected 
equipment.
PressCOMPUTER (1/2), DVI, HDMI, S-VIDEO or 
VIDEO to select the input mode.
• When you press INPUT on the monitor, the 
INPUT list appears.
 Press 
x
/
z
 to switch the input mode.
Adjusting the volume
PressVOL +/– to adjust the volume.
•  You can also adjust the volume using VOL +/– on 
the monitor.
25
• Pressing VOL– 
will lower the volume.
• Pressing VOL+ 
will raise the volume.
• You can set the volume to different levels for each input 
source.
• To adjust sound via the audio output terminal (MONITOR 
OUT), set “Audio Output” to “VAO” in the “Option” menu. 
(See page 38
.)
Note
Displaying the black screen 
and turning off the sound 
temporarily
PressAV MUTE to temporarily display a black 
screen and turn off the sound.
AV MUTE
• Pressing AV MUTE
 again will turn the image back on.
Note
 
						

							24
Operating with the Remote Control
Resize mode
This function allows you to modify or customize the Resize mode to enhance the input image. Depending on 
the input signal, you can choose a desired image.
1 Press RESIZE.
•  The Resize mode menu appears.
•  The menu lists the Resize mode options 
selectable for the type of signal currently 
received.
Zoom 14:9
S.Stretch
Full Resize
Normal
Cinema 16:9
Cinema 14:9
2 Press RESIZE or 
x
/
z
 while the Resize mode menu is displayed on the screen.
• You can also set the Resize mode from the “Option” menu. (See page 40
.)
Note
AV input
Selectable items Description
Normal
Normal
For 4:3 “standard” pictures. A side bar appears on each side.
Zoom 14:9
Zoom 14:9
For 14:9 letterbox pictures. A thin side bar appears on each 
side, and the top and bottom of the image may be cut off 
depending on the input signal.
S. Stretch
S. Stretch
Only the ends of the image are stretched horizontally. 
Full
Full
For 16:9 squeeze pictures.
RESIZE buttonRESIZE button
 
						

							25
Operating with the Remote Control
Selectable items Description
Cinema 16:9
Cinema 16:9
For 16:9 letterbox pictures. The top and bottom of the image 
may be cut off depending on the input signal.
Cinema 14:9
Cinema 14:9
For 14:9 letterbox pictures. The top and bottom of the image 
may be cut off depending on the input signal.
Dot by DotDisplay an image with the same number of pixels on the 
screen (only when receiving 1080I/1080P signal via 
component or HDMI terminals).
Computer input
Selectable items Description
Normal
Normal
Keeps the original aspect ratio in a full screen display.
Full
Full
An image fully fills the screen.
Dot by Dot
Dot by Dot
Detects the resolution of the signal and displays an image with 
the same number of pixels on the screen.
Displays an image that overlaps the screen when a signal of 
greater resolution than the size of the screen is input.
• When using the Resize function to select an image size with a different aspect ratio to a TV program or video image, the 
image will look different from its original appearance. Keep this in mind while choosing an image size.
• The use of the Resize or split-screen function to compress or stretch the image for commercial purposes/public displays in a 
café, hotel, etc. may be an infringement of copyright protected by law for copyright holders. Please use caution.
• While watching non-widescreen images (4:3), if you use the Resize function to fi ll the screen, parts of the outer edge of the 
image will be cut off or distorted. To watch original images as the producers intended, set the Resize mode to “Normal”.
• When “Multi Screen” is set, the Resize mode is fi xed to “Full”.
• When split-screen display is selected, the Resize mode cannot be changed.
• When playing commercial software, parts of the image (like subtitles) may be cropped. In this case select the optimal screen 
size using the Resize function of this monitor. With some software, there may be noise or distortion at the edges of the screen.
This is due to the characteristics of the software, and is not a malfunction.
• Depending on the original image size, black bands may remain at the edges of the screen.
Note
 
						

							26
Operating with the Remote Control
FREEZE
button
AUTO SYNC 
button MAGNIFY 
buttons
RETURN
button
AV MODE 
button
Auto Sync adjustment 
(Auto Sync)
“Clock”, “Phase”, “H-Position”, and “V-Position” are 
automatically adjusted.
PressAUTO SYNC.
•  You can also perform Auto Sync adjustment from 
the “Setup” menu.
Freezing a moving image
1 Press FREEZE.
•  The image is frozen.
2 Press FREEZE again to return to the moving 
image from the currently connected device.
• The still image automatically goes out after 30 minutes.
Note
Selecting AV mode
You can select the appropriate mode for the image, 
such as movie or video game.
PressAV MODE.
• When pressing AV MODE, the AV mode changes 
in the following order: 
Standard Presentation Movie Game sRGB
• See page 30
 for details on AV mode.
• “sRGB” is displayed only when RGB signal is input.
Note
Displaying an enlarged portion 
of an image
Graphs, tables and other portions of images can 
be enlarged. This is helpful when providing more 
detailed explanations.
1 Press MAGNIFY.
• Enlarges the image.
• Pressing 
 or MAGNIFY enlarges or 
reduces the image.
×1×2×3×4×9×16×36
Press.
Press.
Note
•  You can change the location of the enlarged 
image using 
x
/
z
/
{
/
y
.
2 Press RETURN to cancel the operation.
•   The magnifi cation then returns to ×1.
• The selectable magnifi cations differ depending on the 
input signal.
• In the following cases, the image will return to the normal 
size (×1).
– When switching the input mode.
– When RETURN
 has been pressed.
– When the input signal is changed.
– When the input signal resolution and refresh rate 
(vertical frequency) change.
– When the Resize mode is changed.
Note
 
						

							27
Operating with the Remote Control
Split-screen viewing
You can display two pictures on the screen simultaneously.
P&P button
SELECT button COMPUTER (1/2), DVI, 
HDMI, S-VIDEO, VIDEO 
buttons
1 Press P&P.
• Split-screen appears.
•  The current input is moved to the left side screen display and surrounded by a blue frame.
•  The other input appears on the right side screen display.
123456789101112 5 10 15 20 25
30 352345678910
2 Press SELECT to set either screen to be active.
•  The active screen, surrounded by a blue frame, has sound output.
3 Press COMPUTER (1/2), DVI, HDMI, S-VIDEO orVIDEO to select another input source on the active 
screen.
•  A selected image appears.
4 Press P&P to exit split-screen.
• This function does not work under the following input conditions:
1) Two pictures from the same source.
2) Two pictures from HDMI and DVI.
3) Pictures from S-VIDEO or VIDEO on the right side screen are displayed.
• While split-screen is displayed, the FREEZE function does not work.
• Picture quality may deteriorate when interlace signals (for example, 480I, 576I, 1035I, and 1080I) are displayed on the active
screen.
Note
 
						

							28
Menu Operations
•  You need to bring up the On-Screen Display to 
perform settings for the monitor. The On-Screen 
Display for the settings is called “Menu”.
•  The Menu enables various settings and 
adjustments. (See page 29.)
•  The Menu can be operated with the remote 
control.
Basic menu operations
RETURN
button Adjustment/
MOUSE
buttonsMENU
button
ENTER
button
1 Press MENU and the MENU screen appears.
MENU[
Picture]
PictureAudio Power Control 
Contrast  OPC [Off]  AV Mode  [Standard]
Brightness 
Color
Tint
Sharpness 
Advanced 
Reset[  30] 
[    0] 
[    0] 
[    0] 
[    0] 
Red  [    0] 
Green  [    0] 
Blue  [    0] 
Backlight [+16] 
+
+
+ +
+
+
+
2 Press 
{
/
y
 to select the desired menu.
Audio 
Treble 
Bass
Balance
Reset[  0] 
[  0] -
L+
[  0]  - +
R
StandardPower Control 
3 Press 
x
/
z
 to select the desired menu item. 
 Press ENTER to proceed if necessary.
Audio 
Treble
Bass
Balance
Reset[  0] 
[  0] -
L+
[  0] -+
R
StandardPower Control 
4 Press 
x
/
z
 or 
{
/
y
 to select the desired item or 
adjust the item to the desired level. 
PressENTERif necessary.
5 Press MENU to exit the MENU.
 Press RETURN as necessary to return to the 
previous MENUs.
„ Using the control panel of the 
monitor
You can also operate the Menu using the control 
panel of the monitor.
Button operations on the control panel correspond 
to the ones on the remote control.
• Menu options differ in the selected input modes, but the 
operating procedures are the same.
• The screens in the owner’s manual are for explanation 
purposes (some are enlarged, others cropped) and may 
vary slightly from the actual screens.
Note
„ About Guide Display
The Guide Display at the bottom of the screen 
shows operations with an On-Screen Display.
The bar above is an operational guide for the 
remote control. The bar will change in accordance 
with each menu setting screen.
: Select : Enter : End: Back Select desired itemENTERRETURNMENU