Edimax Router BR-6424n User Manual

							 
61
Internet when there’s a connect attempt,   
 
Manual - only connects to Internet when 
‘Connect’ button on this page is pressed, and 
disconnects when ‘Disconnect button is 
pressed. 
Idle Time Out Please specify the time to shutdown internet 
connect after no internet activity is detected in 
minute(s). This option is only available when 
connection type is ‘Connect on Demand’. 
TTL  Time-to-live (TTL) is a value in an Internet 
Protocol packet that tells a network router 
whether or not the packet has been in the 
network too long and should be discarded. 
 
If you wish to select another connection type as broadband connection 
type, click ‘Back’; or you can click ‘OK’ to finish with quick setup. 
You’ll see the following messages: 
 
 
 
Please click ‘Apply’ to save changes you made and restart the broadband 
router, this requires about 30 seconds and the broadband router will stop 
responding (this is normal and is not malfunction). You can reconnect to 
this broadband router and continue on other settings later. 
  
						

							 
62
3-2-4 PPTP 
 
If your ISP requires you to use PPTP (Point-to-Point Tunneling Protocol) 
to establish connection, you can select this connection type to establish 
Internet connection. 
 
PPTP requires two kinds of setting: WAN interface setting (setup IP 
address) and PPTP setting (PPTP user name and password). Here we start 
from WAN interface setting first: 
 
 
 
Select the type of how you obtain IP address from your service provider 
here. You can choose ‘Obtain an IP address automatically’ (equal to 
DHCP, please refer to ‘Cable Modem’ section above), or ‘Use the 
following IP address’ (i.e. static IP address).   
 
WAN interface settings must be correctly set, or the Internet connection 
will fail even those settings of PPTP settings are correct. Please contact 
your Internet service provider if you don’t know what you should fill in 
these fields. 
  
						

							 
63
Now please go to PPTP settings section: 
 
 
 
Here are descriptions of every setup items: 
 
Item Name Description 
User ID  Please input user ID (user name) assigned by 
your Internet service provider here. 
Password  Please input the password assigned by your 
Internet service provider here. 
PPTP Gateway  Please input the IP address of PPTP gateway 
assigned by your Internet service provider 
here. 
Connection ID Please input the connection ID here, this is 
optional and you can leave it blank. 
MTU  Please input the MTU value of your network 
connection here. If you don’t know, you can use 
default value. 
BEZEQ-ISRAEL  Check ‘Enable’ box if you’re using BEZEQ 
network service in Israel. Do not check this 
box if you’re using other Internet service 
provider. 
Connection Type Please select the connection type of Internet 
connection you wish to use. There are 3 
options:  
  
						

							 
64
‘Continuous’ - keep internet connection alive, 
do not disconnect.   
 
’Connect on Demand’ - only connects to 
Internet when there’s a connect attempt,   
 
Manual - only connects to Internet when 
‘Connect’ button on this page is pressed, and 
disconnects when ‘Disconnect button is 
pressed. 
Idle Time Out Please specify the time to shutdown internet 
connect after no internet activity is detected in 
minute(s). This option is only available when 
connection type is ‘Connect on Demand’. 
 
If you wish to select another connection type as broadband connection 
type, click ‘Back’; or you can click ‘OK’ to finish with quick setup. 
You’ll see the following messages: 
 
 
 
Please click ‘Apply’ to save changes you made and restart the broadband 
router, this requires about 30 seconds and the broadband router will stop 
responding (this is normal and is not malfunction). You can reconnect to 
this broadband router and continue on other settings later. 
  
						

							 
65
3-2-5 L2TP 
 
If your ISP requires you to use L2TP (Layer-2 Tunneling Protocol) to 
establish connection, you can select this connection type to establish 
Internet connection. L2TP is another popular connection method for 
xDSL and other Internet connection types, and all required setting items 
are the same with PPTP connection. 
 
Like PPTP, there are two kinds of required setting, we’ll start from ‘WAN 
Interface Settings’: 
 
 
 
Please select the type of how you obtain IP address from your service 
provider here. You can choose ‘Obtain an IP address automatically’ (equal 
to DHCP, please refer to ‘Cable Modem’ section above), or ‘Use the 
following IP address’ (equal to static IP address, please refer to ‘PPPoE 
xDSL’ section above).   
 
WAN interface settings must be correctly set, or the Internet connection 
will fail even those settings of L2TP settings are correct. Please contact 
your Internet service provider if you don’t know what you should fill in 
these fields. 
 
Now please go to L2TP settings section: 
 
  
						

							 
66
 
Here are descriptions of every setup items: 
 
Item Name Description 
User ID Please input user ID (user name) assigned by 
your Internet service provider here. 
Password Please input the password assigned by your 
Internet service provider here. 
L2TP Gateway Please input the IP address of L2TP gateway 
assigned by your Internet service provider 
here. 
MTU Please input the MTU value of your network 
connection here. If you don’t know, you can use 
default value. 
Connection Type Please select the connection type of Internet 
connection you wish to use. There are 3 
options:  
 
‘Continuous’ - keep internet connection alive, 
do not disconnect.   
 
’Connect on Demand’ - only connects to 
Internet when there’s a connect attempt,   
 
Manual - only connects to Internet when 
‘Connect’ button on this page is pressed, and 
disconnects when ‘Disconnect button is 
pressed. 
Idle Time Out Please specify the time to shutdown internet  
						

							 
67
connect after no internet activity is detected in 
minute(s). This option is only available when 
connection type is ‘Connect on Demand’. 
 
If you wish to select another connection type as broadband connection 
type, click ‘Back’; or you can click ‘OK’ to finish with quick setup. 
You’ll see the following messages: 
 
 
 
Please click ‘Apply’ to save changes you made and restart the broadband 
router, this requires about 30 seconds and the broadband router will stop 
responding (this is normal and is not malfunction). You can reconnect to 
this broadband router and continue on other settings later. 
  
						

							 
68
3-2-6 Telstra Big Pond 
 
This connection type only works for Telstra big pond network service in 
Australia. DO NOT select this connection type if you’re not using Telstra 
big pond network service. 
 
 
 
Here are descriptions of every setup items: 
 
Item Name Description 
User Name Please input the user name assigned by Telstra.
Password Please input the password assigned by Telstra. 
User device login 
server manually Check this box to choose login server by 
yourself. 
Login Server Please input the IP address of login server 
here. 
 
If you wish to select another connection type as broadband connection 
type, click ‘Back’; or you can click ‘OK’ to finish with quick setup. 
You’ll see the following messages: 
 
 
  
						

							 
69
Please click ‘Apply’ to save changes you made and restart the broadband 
router, this requires about 30 seconds and the broadband router will stop 
responding (this is normal and is not malfunction). You can reconnect to 
this broadband router and continue on other settings later. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
						

							 
70
3-2-7 WISP ( Wireless ISP Connection Mode ) 
 
You can connect with ISP via the router wirelessly, because the router 
provides WISP connection mode. Click “ Enable “ and “ Select Site 
Survey “ button   
 
Here you will find many Wireless Access Points as follows. To Choose an 
Access Point which you would like connect , then click “Select” button 
and “Done” . 
 
 
Here you will see the Access Point which you select.   
 
Here we provide WEP and PWA-PSK security settings for you to connect 
with ISP (Access Point). If your ISP does not ask you to input the security 
key, please choose “ Disable” and click “ Apply “ to save changes you