Dukane Projector 8527 User Manual

							71
OPTION menu
ItemDescription
SERVICE
(continued)
CLONING(continued)
Load MyScreen data
• 
 Please save the image data as "pj_logo.bmp" or 
"pj_logo.gif" into USB memory.
• 
 Please note that the only compatible formats are 
as follows.
-File format Windows BMP   bit/pixel: 4/8/16/24/32bit
Compression format : 
Without compression/RLE 
GIF
-Image size: more than 36x36, less than 1280x800
• 
 If two kinds of file format are saved, "pj_logo.
bmp" will be registered into MyScreen data.
• 
 If MyScreen LOCK or MyScreen PASSWORD 
is turned ON, the data of MyScreen cannot be 
loaded.
Setting the data
• 
 Operating the SAVE function under CLONING 
will name the file as "pj_data.bin" into the USB 
memory. Please do not attempt to change the file 
name or the folder structure.
• 
 If a file with the same name already exists, it will 
be overwritten by operating the SAVE function.
Loading function
• 
 Please note that saved data from other model 
cannot be loaded.
• 
 Please note that, if any of the following functions: 
MyScreen PASSWORD, PIN LOCK, TRANSITION 
DETECTOR, MY

 TEXT PASSWORD under 
SECURITY menu or MyScreen Lock under 
SCREEN menu is ON, the respective saved data 
cannot be loaded. 
• 
 Please note that the saved settings of KEYSTONE 
(SETUP menu) and AUTO KEYSTONE (OPTION 
menu) cannot be loaded when TRANSITION 
DETECTOR (SECURITY menu) is ON.
•  Please note that the saved data of START UP 
and MyScreen Lock under SCREEN menu cannot 
be loaded if  MyScreen P
ASSWORD under 
SECURITY menu is ON.
• 
 Please note that the saved data of MY TEXT 
WRITING cannot be loaded if MY 

TEXT 
PASSWORD under SECURITY menu is ON.
(continued on next page) 
						

							72
OPTION menu
ItemDescription
SERVICE
(continued) INFORMATION
Selecting this item displays a dialog titled “INPUT_INFORMATION”. 
It shows the information about the current input.
• The “FRAME LOCK” message on the dialog means the frame lock 
function is working. 
• This item can't be selected for no signal and sync out.
• When the MY TEXT DISPLAY is set to ON, the MY TEXT is 
displayed together with the input information in the  
INPUT_INFORMATION box (

79).
FACTORY RESET
Selecting OK using the ► button performs this function. By this 
function, all the items in all of menus will collectively return to the 
initial setting. Note that the items AUTO BLANK, STANDBY MODE, 
LAMP TIME, FILTER TIME, LANGUAGE, FILTER MESSAGE, 
NETWORK and SECURITY settings are not reset. CANCEL 
ð OK
Be sure to set ALTITUDE after resetting all the settings (
 66).  
						

							73
NETWORK menu
NETWORK menu
See the Network Guide for details of NETWORK operation.
Remember that incorrect network settings on this projector may cause trouble on 
the network. Be sure to consult with your network administrator before connecting 
to an existing access point on your network. 
						

							74
SECURITY menu
(continued on next page) This projector is equipped with security functions.
From the SECURITY menu, items shown in the table 
below can be performed.
To use SECURITY menu: User registration is required 
before using the security functions.
Enter to the SECURITY menu
1.  Press the ► button. The ENTER PASSWORD box will be displayed.  
2. 
 Use the ▲/▼/◄/► buttons to enter the registered password. 
    The factory default password is as follows.
    
        This password can be changed ( below
). Move the cursor to
    the right side of the ENTER PASSWORD box and press 
    the ► button to display the SECURITY menu. • It is strongly recommended the factory default password to be 
changed as soon as possible.
• If an incorrect password is input, the ENTER PASSWORD box 
will be displayed again. If incorrect password is input 3 times, the 
projector will turn off. Afterwards the projector will turn off every time 
an incorrect password is input.
3. 
 Items shown in the table below can be performed.
If you have forgotten your password(1)  While the ENTER PASSWORD box is displayed, press and hold the 
RESET button on the remote control for about 3 seconds or press 
and hold the  INPUT button for 3 seconds while pressing the ► 
button on the projector
.
(2) 
 The 10 digit Inquiring Code will be displayed. Contact your dealer   
with the 10 digit Inquiring Code. Your password will be sent after your user registration information 
is confirmed.
• If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will 
close. If necessary, repeat the process from (1). 
 
Item Description
SECURITY 
PASSWORD  CHANGE
(1)  Use the ▲/▼ buttons on the SECURITY menu 
to select SECURITY  PASSWORD CHANGE 
and press the ► button to display the ENTER 
NEW PASSWORD box.
(2) 
 Use the ▲/▼/◄/► buttons to enter the new password.
(3)  Move the cursor to the right side of the ENTER 
NEW PASSWORD box and press the ► button 
to display the NEW PASSWORD AGAIN box, 
enter the same password again. 
(4) 
 Move the cursor to the right side of the NEW 
PASSWORD AGAIN box and press the ► 
button and the NOTE NEW PASSWORD box 
will be displayed for about 30 seconds, please 
make note of the password during this time.
Pressing the ENTER button on the remote control or ► button on the 
projector will close the NOTE NEW PASSWORD box.
• Please do not forget your password.
SECURITY menu
3033 
						

							75
SECURITY menu
ItemDescription
MyScreen 
PASSWORD
The MyScreen PASSWORD function can be used to prohibit access to the 
MyScreen function and prevent the currently registered MyScreen image 
from being overwritten.
1 Turning on the MyScreen PASSWORD1-1  Use the ▲/▼ buttons on the SECURITY menu to 
select MyScreen PASSWORD and press the ► 
button to display the MyScreen PASSWORD on/
off menu.
1-2 
 Use the ▲/▼ buttons on the MyScreen 
PASSWORD on/off menu to select ON. 
The ENTER NEW PASSWORD box (small) 
will be displayed.
1-3 
 Use the ▲/▼/◄/► buttons to enter the 
password. Move the cursor to the right side 
of the ENTER NEW PASSWORD box (small) 
and press the ► button to display the NEW 
PASSWORD AGAIN box, enter the same 
PASSWORD again.
1-4 
 Move the cursor to the right side of the 
NEW PASSWORD AGAIN box and press 
the ► button to display the NOTE NEW 
PASSWORD box for about 30 seconds, 
please make note of the password during 
this time.  Pressing the ENTER

 button on the remote control or ► button on the 
projector will return to MyScreen PASSWORD on/off menu.
When a password is set for MyScreen:
• The MyScreen registration function (and menu) will be unavailable.
• The MyScreen Lock menu will be unavailable.
• The START UP setting will be locked on MyScreen (and the menu will be 
unavailable).
Turning the MyScreen PASSWORD off will allow normal operation of these 
functions.
• Please do not forget your MyScreen PASSWORD.
2 Turning off the MyScreen PASSWORD2-1  Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off 
menu.
2-2 
 Select OFF to display the ENTER 
PASSWORD box (large). Enter the registered 
password and the screen will return to the 
MyScreen PASSWORD on/off menu.
If an incorrect PASSWORD is input, the menu will 
close. If necessary, repeat the process from 2-1.
3 If you have forgotten your password3-1  Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off 
menu.
3-2 
 Select OFF to display the ENTER PASSWORD box (large). The 10 digit 
Inquiring Code will be displayed inside the box.
3-3 
 Contact your dealer with the 10 digit Inquiring Code. Your password will 
be sent after your user registration information is confirmed.
(continued on next page)
ENTER NEW PASSWORD  box (small)
ENTER PASSWORD box  (large) 
						

							76
SECURITY menu
ItemDescription
PIN LOCK
PIN LOCK is a function which prevents the projector from being used unless 
a registered Code is input.
1 Turning on the PIN LOCK1-1  Use the ▲/▼ buttons on the SECURITY menu 
to select PIN LOCK and press the ► button or 
the ENTER button to display the PIN LOCK on/off 
menu.
1-2 
 Use the ▲/▼ buttons on the PIN LOCK on/
off menu to select ON and the Enter PIN 
Code box will be displayed. 
1-3 
 Input a 4 part PIN code using the ▲/▼/◄/►, 
COMPUTER or INPUT button. 
The PIN Code again box will appear. Reenter  
the same PIN code. 

This will complete the PIN 
code registration.
• If there is no key input for about 55 seconds  
while the Enter PIN Code box or the PIN Code again box is displayed, 
the menu will close. If necessary, repeat the process from 1-1.
Afterwards, anytime the projector is restarted after AC power  is turned off 
the Enter PIN Code box will be displayed. Enter the registered PIN code.
The projector can be used after entering the registered PIN code. If an 
incorrect PIN code is input, the Enter PIN code box will be displayed again.
If an incorrect PIN code is input 3 times, the projector will turn of f. Afterwards 
the projector will turn off every time an incorrect PIN code is input. The 
projector will also turn off if there is no key input for about 5 minutes while 
the Enter PIN code box is displayed.
This function will activate only when the projector is started after  AC power 
is turned off.
• Please do not forget your PIN code.
2 Turning off the PIN LOCK2-1  Follow the procedure in 1-1 to display the PIN LOCK on/off menu. 
2-2  Use the ▲/▼ buttons to select OFF and the Enter PIN Code box will be 
displayed. 
Enter the registered PIN code to turn the PIN LOCK function off.
If an incorrect PIN code is input 3 times, the projector will turn of f. 
3 If you have forgotten your PIN code3-1  While the Enter PIN code box is displayed, press and hold the RESET 
button for three seconds or press and hold the  INPUT button for 3 
seconds while pressing the ► button on the projector. 
The 10 digit Inquiring Code will be displayed.
• If there is no key input for about 5 minutes 
while the Inquiring Code is displayed, the 
projector will turn off.
3-2 
 Contact your dealer with the 10 digit Inquiring Code. Your PIN code will 
be sent after your user registration information is confirmed.
(continued on next page) 
						

							77
SECURITY menu
ItemDescription
TRANSITION  DETECTOR
If this function is set to ON and the vertical angle of 
the projector or the INSTALLATION setting is different 
from the previous recorded setting, the TRANSITION 
DETECTOR ON alarm will be displayed and the input 
signal will not be displayed.
• To display the signal again, set this function OFF.
• After about 5 minutes of displaying the TRANSITION DETECTOR ON 
alarm, the lamp will turn off.
• Keystone adjustment feature has been prohibited as long as the 
TRANSITION DETECTOR function is on.
1 Turning on the TRANSITION DETECTOR1-1  Use the ▲/▼ buttons on the SECURITY menu to 
select TRANSITION DETECTOR and press  the ► 
or the ENTER button to display the TRANSITION 
DETECTOR on/off menu.
1-2 
 Use the ▲/▼ buttons on the TRANSITION 
DETECTOR on/off menu to select ON. 
Selecting ON will save the setting of the 
current angle and the INSTALLATION setting. 
The ENTER NEW PASSWORD box (small) 
will be displayed.
1-3  Use the ▲/▼/◄/► buttons to enter a 
password. Move the cursor to the right side 
of the ENTER NEW PASSWORD box (small) 
and press the ► button to display the NEW 
PASSWORD AGAIN box, enter the same 
password again.
1-4 
 Move the cursor to the right side of the  
NEW PASSWORD AGAIN box and press  
the ► button to display the NOTE NEW  
PASSWORD box for about 30 seconds,  
please make note of the password during this time.
Pressing the ENTER button on the remote control or the ► button on the 
projector will return to the TRANSITION DETECTOR on/off menu.
• Please do not forget your TRANSITION DETECTOR password.
• This function will activate only when the projector is started after turning off 
the AC power.
• This feature may not function properly if the projector is not in a stable 
position when ON is selected.
2 Turning off the TRANSITION DETECTOR2-1  Follow the procedure in 1-1 to display the TRANSITION DETECTOR on/off menu.2-2  Select OFF to display the ENTER 
PASSWORD box (large). Enter the registered 
password and the screen will return to the 
TRANSITION DETECTOR on/off menu.
If an incorrect password is input, the menu will 
close. If necessary, repeat the process from 2-1.
3 If you have forgotten your password3-1  Follow the procedure in 1-1 to display the TRANSITION DETECTOR on/off menu.3-2  Select OFF to display the ENTER PASSWORD box (large). The 10 digit 
Inquiring Code will be displayed inside the box.
3-3 
 Contact your dealer with the 10 digit Inquiring Code. Your password will 
be sent after your user registration information is confirmed.
     (continued on next page)
ENTER NEW PASSWORD  box (small)
ENTER PASSWORD box  (large) 
						

							78
SECURITY menu
ItemDescription
MY TEXT 
PASSWORD
The MY TEXT PASSWORD function can prevent the MY TEXT from being 
overwritten. When the password is set for the MY TEXT;
• The MY TEXT DISPLAY menu will be unavailable, which can prohibit 
changing the DISPLAY setting.
• The MY TEXT WRITING menu will be unavailable, which can prevent the 
MY TEXT from being overwritten.
1 Turning on the MY TEXT PASSWORD1-1  Use the ▲/▼ buttons on the SECURITY menu to 
select the MY TEXT P ASSWORD and press the 
► button to display the MY TEXT PASSWORD 
on/off menu.
1-2 
 Use the ▲/▼ buttons on the MY TEXT 
PASSWORD on/of

f menu to select ON. The 
ENTER NEW PASSWORD box (small) will 
be displayed.
1-3 
 Use the ▲/▼/◄/► buttons to enter the 
password. Move the cursor to the right side 
of the ENTER NEW PASSWORD box (small) 
and press the ► button to display the NEW 
PASSWORD AGAIN box, and then enter the 
same password again.
1-4 
 Move the cursor to the right side of the NEW 
PASSWORD AGAIN box and press ► button 
to display the NOTE NEW PASSWORD box 
for about 30 seconds, then please make note 
of the password during this time.
Pressing the ENTER

 button on the remote control or ► button on the 
projector will return to the MY TEXT PASSWORD on/off menu. 
2 Turning off the MY TEXT PASSWORD2-1  Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/of f 
menu.
2-2 
 Select OFF to display the ENTER 
PASSWORD box (l

arge). Enter the registered 
password and the screen will return to the 
MY TEXT PASSWORD on/off menu. 
If an incorrect password is input, the menu will close. 
If necessary, repeat the process from 2-1
3 If you have forgotten your password3-1  Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/of f 
menu.
3-2 
 Select OFF to display the ENTER PASSWORD box (large). The 10 digit 
inquiring code will be displayed inside the box. 
3-3 
 Contact your dealer with the 10 digit inquiring code. Your password will 
be sent after your user registration information is confirmed.
(continued on next page)
ENTER NEW PASSWORD   box (small)
ENTER PASSWORD box  (large) 
						

							79
SECURITY menu
ItemDescription
MY TEXT  DISPLAY
(1)  Use the ▲/▼ buttons on the SECURITY menu to 
select the MY TEXT DISPLA Y and press the ► or 
ENTER button to display the MY TEXT DISPLAY 
on/off menu.
(2) 
 Use the ▲/▼ buttons on the MY TEXT DISPLAY

 on/off menu to select 
on or off.
ON  ó OFF
When it is set ON, the MY TEXT will be displayed 
on the START UP screen and the INPUT_
INFORMATION when the INFORMATION on the 
SERVICE menu is chosen.
• This function is available only when the MY TEXT 
PASSWORD function is set to the OFF.
MY TEXT 
WRITING
(1)  Use the ▲/▼ buttons on the 
SECURITY menu to select the MY 
TEXT WRITING and press the ► 
button. The MY
 TEXT WRITING dialog 
will be displayed.
(2) 
 The current MY TEXT will be displayed 
on the first 3 lines. If not yet written, the 
lines will be blank.  
Use the ▲/▼/◄/► buttons and the 
ENTER

 or INPUT button to select and 
enter characters. To erase 1 character 
at one time, press the RESET button or 
press the ◄ and INPUT button at the 
same time. Also if you move the cursor 
to DELETE or ALL CLEAR on screen 
and press the ENTER or INPUT button, 
1 character or all characters will be 
erased. The MY TEXT can be input up 
to 24 characters on each line.
(3) 
 To change an already inserted 
character, press the ▲/▼ button to move 
the cursor to one of the first 3 lines, and 
use the ◄/► buttons to move the cursor 
on the character to be changed.
After pressing the ENTER or INPUT button, the character is selected. 
Then, follow the same procedure as described at the item (2) above.
(4) 
 To finish entering text, move the cursor to the OK on screen and press 
the ►,  ENTER or INPUT button. 

To revert to the previous MY TEXT 
without saving changes, move the cursor to the CANCEL on screen and 
press the ◄, ENTER or INPUT button.
• The MY TEXT WRITING function is available only when the MY TEXT 
PASSWORD function is set to OFF.
CLONING LOCKThe CLONING operation under OPTION _SERVICE menu is not available if 
ON is selected. 
						

							80
Presentation tools
Presentation tools
The PC-LESS Presentation reads image and audio data from the storage media 
inserted into the USB TYPE A port and displays the image in the following modes.
The PC-LESS Presentation can be started by selecting the USB TYPE A port as 
the input source.
This feature allows you to make your presentations without using your computer .
PC-LESS Presentation
- Thumbnail mode (81)
- Full Screen mode (
85)
- Slideshow mode (
87)
[Supported storage media] • USB memory (USB memory type, USB hard disk and USB card reader type)
• USB readers (adapters) that have more than one USB slot may not 
work (if the adapter is acknowledged as multiple devices connected).
• USB devices with security software may not work.
• Be careful when inserting or removing a USB device. (
13, 83)
NOTE
• NTFS is not supported.
NOTE
[Supported format]
• FAT12, FAT16 and FAT32
The projector has the following convenient tools that enable on-screen 
presentations easily and quickly:
- PC-LESS Presentation (
below )
- 
 Drawing function
  
 Drawing function enables you to draw on the projector’s screen with USB 
mouse or tablets connected to the  USB TYPE A ports. For details, refer to the 
manual for peripheral equipment.
- USB Display (
90)