Dukane Projector 6645WA User Manual

							100
10.	Drag	the	selected	[	•	]	mark	to	the	point	you	wish	to	correct	
and drop it.
•	 When	you	click	somewhere	within	the	project	image	area,	the	
nearest [ •	]	mark	will	go	to	the	position	where	the	mouse	cur-
sor is.
11. Repeat Step 9 and 10 to correct the distortion of the projected 
image.
12. After completing, right-click the mouse.
 The green frame and the mouse pointer will disappear from the 
projected image area. This will complete the correction.
13.	Click	the	“X”	(close)	button	on	the	“4-point	Correction”	window.
	 The	“4-point	Correction”	window	will	disappear	and	the	4-point	
correction	will	take	effect.
14.	Click	the	“		”	button	on	the	control	window	to	exit	the	GCT.
TIP:
•	 After	performing	the	4-point	correction,	you	can	save	the	4-point	correction	data	to	the	projector	by	clicking	“File”	→	“Export	to	
the	projector…”	on	the	“4-point	Correction”	window.
•	 See	the	Help	of	Image	Express	Utility	Lite	for	operating	“4-point	Correction”	window	and	other	functions	than	GCT.	(→	page	96,	
97)
7. User Supportware  
						

							101
❹ Controlling the Projector over a LAN (PC Control Utility Pro 4/
Pro 5)
Using	the	utility	software	“PC	Control	Utility	Pro	4”	and	“PC	Control	Utility	Pro	5”	available on the Dukane web site
the	projector	can	be	controlled	from	a	computer	over	a	LAN.
PC	Control	Utility	Pro	4	is	a	program	compatible	with	Windows.	(→	this	page)
PC	Control	Utility	Pro	5	is	a	program	compatible	with	Mac	OS.	(→	page	104)
Control Functions
Power	On/Off,	signal	selection,	picture	freeze,	picture	mute,	audio	mute,	adjusting,	error	message	notification,	
event	schedule.
Screen	of	PC	Control	Utility	Pro	4
This	section	provides	an	outline	of	preparation	for	use	of	PC	Control	Utility	Pro	4/Pro	5.	For	information	on	how	to	use	
PC	Control	Utility	Pro	4/Pro	5,	see	Help	of	PC	Control	Utility	Pro	4/Pro	5.	(→	page	103, 105)
Step	1:	Install	PC	Control	Utility	Pro	4/Pro	5	on	the	computer.
Step	2:	Connect	the	projector	to	a	LAN.
Step	3:	Start	PC	Control	Utility	Pro	4/Pro	5.
•	 To	run	PC	Control	Utility	Pro	4	on	Windows	8.1,	Windows	8	and	Windows	XP,	“Microsoft	.NET	Framework	Version	
2.0”	is	required.	The	Microsoft	.NET	Framework	Version	2.0,	3.0	or	3.5	is	available	from	Microsoft’s	web	page.	
Download	and	install	it	on	your	computer.
TIP:
•	 With	PC	Control	Utility	Pro	4,	control	is	also	possible	by	RS-232C	serial	communications	connected	to	the	projector’s	PC	CONTROL	
terminal.
Using on Windows
Step 1: Install PC Control Utility Pro 4 on the computer
NOTE:
•	 To	install	or	uninstall	the	program,	the	Windows	user	account	must	have	[Administrator]	privilege.
•	 Exit	all	running	programs	before	installation.	If	another	program	is	running,	the	installation	may	not	be	completed.
7. User Supportware  
						

							102
	 Read	“END	USER	LICENSE	AGREEMENT”	carefully.
4	 If	you	agree,	click	“I	accept	the	terms	in	the	license	agreement”	and	then	click	“Next”.
•	 Follow	the	instructions	on	the	installer	screens	to	complete	the	installation.
•	 When	the	installation	is	complete,	you	will	return	to	the	menu	window.
TIP:
•	Uninstalling	PC	Control	Utility	Pro	4
To	uninstall	PC	Control	Utility	Pro	4,	do	the	same	procedures	stated	as	in	“Uninstalling	Virtual	Remote	Tool”.	Read	“Virtual	Remote	
Tool”	as	“PC	Control	Utility	Pro	4”	(→	page	109)
Go to the Dukane or NEC website for the latest software. 
Visit  www.dukaneav.com and go to the Service page for downloads and links. 
http://www.dukane.com/av/service/downloads.asp.
Or visit URL: http://www.nec-display.com/dl/en/index.html 
 
1.       Download – PC Control Utility Pro 4 
 
2.       Go to Next 
 
3.       Review license Agreement.
7. User Supportware  
						

							103
Step 2: Connect the projector to a LAN.
Connect	the	projector	to	the	LAN	by	following	the	instructions	in	“Connecting	to	a	Wired	LAN”	(→	page	82)	and	“Con-
necting	to	a	Wireless	LAN	(Optional:	NP05LM	series)”	(→	page	83).
Step 3: Start PC Control Utility Pro 4
Click	“Start”	→	“All	programs”	or	“Programs”	→	“NEC	Projector	User	Supportware”	→	“PC	Control	Utility	Pro	4”	→ 
“PC	Control	Utility	Pro	4”.
NOTE:	
•	 For	the	Schedule	function	of	the	PC	Control	utility	Pro	4	to	work,	you	must	have	your	computer	running	and	not	in	standby/
sleep	mode.	Select	“Power	Options”	from	the	“Control	Panel”	in	Windows	and	disable	its	standby/sleep	mode	before	running	the	
scheduler.
[Example]	For	Windows	7:
Select	“Control	Panel”	→	“System	and	Security”	→	“Power	Options”	→	“Change	when	the	computer	sleeps”	→	“Put	the	computer	
to	sleep”	→	“Never”.	
NOTE:	
•	 When	[NORMAL]	is	selected	for	[STANDBY	MODE]	from	the	menu,	the	projector	cannot	be	turned	on	via	the	network	(wired	LAN/
wireless	LAN)	connection.
TIP:
Viewing	the	Help	of	PC	Control	Utility	Pro	4
•	 Displaying	the	Help	file	of	PC	Control	Utility	Pro	4	while	it	is	running.
	 Click	“Help	(H)”	→	“Help	(H)	…”	of	window	of	PC	Control	Utility	Pro	4	in	this	order.
 The pop-up menu will be displayed.
•	 Displaying	the	help	file	using	the	Start	Menu.
	 Click	“Start”	→	“All	programs”	or	“Programs”	→	“NEC	Projector	User	Supportware”	→	“PC	Control	Utility	Pro	4”	→ 
“PC	Control	Utility	Pro	4	Help”.
 The Help screen will be displayed.
7. User Supportware  
						

							104
Using on Mac
Step 1: Install PC Control Utility Pro 5 on the computer
1.	Go to the projector website at: Dukaneav.com.
2.	Locate the projector model.
 
3.	Locate the	Mac	OS	X	fdownloads.
4.	 Double-click	“PC	Control	Utility	Pro	5.pkg”.
 The installer will start.
5.	 Click	“Next”.
	 “END	USER	LICENSE	AGREEMENT”	screen	will	be	displayed.
6.	 Read	“END	USER	LICENSE	AGREEMENT”	and	click	“Next”.
 The confirmation window will be displayed
7.	 Click	“I	accept	the	terms	in	the	license	agreement”.
 Follow the instructions on the installer screens to complete the installation.
Step 2: Connect the projector to a LAN
Connect	the	projector	to	the	LAN	by	following	the	instructions	in	“Connecting	to	a	Wired	LAN”	(→	page	82)	and	“Con-
necting	to	a	Wireless	LAN	(Optional:	NP05LM	series)”	(→	page	83).
Step 3: Start PC Control Utility Pro 5
1. Open your Applications folder in OS X.
2.	 Click	the	“PC	Control	Utility	Pro	5”	folder.
3.	 Click	the	“PC	Control	Utility	Pro	5”	icon.
 PC Control Utility Pro 5 will start.
NOTE:	
•	 For	the	Schedule	function	of	the	PC	Control	utility	Pro	5	to	work,	you	must	have	your	computer	running	and	not	in	sleep	mode.	
Select	“Energy	Saver”	from	the	“System	Preferences”	in	Mac	and	disable	its	sleep	mode	before	running	the	scheduler.
•	 When	[NORMAL]	is	selected	for	[STANDBY	MODE]	from	the	menu,	the	projector	cannot	be	turned	on	via	the	network	(wired	LAN/
wireless	LAN)	connection.
7. User Supportware  
						

							105
TIP:
Uninstalling a software program
1.	 Put	the	“PC	Control	Utility	Pro	5”	folder	to	the	Trash	icon.
2.	 Put	the	configuration	file	of	PC	Control	Utility	Pro	5	to	the	Trash	icon.
•	 The	configuration	file	of	PC	Control	Utility	Pro	5	is	located	in	“/Users//Application	Data/NEC	
Projector	User	Supportware/PC	Control	Utility	Pro	5”.
Viewing	the	Help	of	PC	Control	Utility	Pro	5
•	Displaying	the	Help	file	of	PC	Control	Utility	Pro	5	while	it	is	running.	
•	 From	the	menu	bar,	click	“Help”	→	“Help”	in	this	order.	
 The Help screen will be displayed.
•	Displaying	the	Help	using	the	Dock	
1.	 Open	“Application”	folder	in	OS	X.
2.	 Click	the	“PC	Control	Utility	Pro	5”	folder.
3.	 Click	the	“PC	Control	Utility	Pro	5	Help”	icon.
 The Help screen will be displayed.	
7. User Supportware  
						

							106
❺ Using the Computer Cable (VGA) to Operate the 
Projector (Virtual Remote Tool)
Available on the Dukane website.
This	will	help	you	perform	operations	such	as	projector’s	power	on	or	off	and	signal	selection	via	the	computer	cable	
(VGA),	serial	cable,	or	LAN	connection.	Only	via	serial	connection	it	is	also	used	to	send	an	image	to	the	projector	
and	register	it	as	the	logo	data	of	the	projector.	After	registering	it,	you	can	lock	the	logo	to	prevent	it	from	changing.
Control Functions
Power	On/Off,	signal	selection,	picture	freeze,	picture	mute,	audio	mute,	Logo	transfer	to	the	projector,	and	remote	
control	operation	on	your	PC.
Virtual	Remote	screenToolbar
This	section	provides	an	outline	of	preparation	for	use	of	Virtual	Remote	Tool.
For	information	on	how	to	use	Virtual	Remote	Tool,	see	Help	of	Virtual	Remote	Tool.	(→	page	111)
Step	1:	Install	Virtual	Remote	Tool	on	the	computer.	(→	page	107)
Step	2:	Connect	the	projector	to	the	computer.	(→	page	109)
Step	3:	Start	Virtual	Remote	Tool.	(→	page	110)
TIP:
•	 Virtual	Remote	Tool	can	be	used	with	a	LAN	and	a	serial	connection.	USB	connection	is	not	supported	by	Virtual	Remote	Tool.
•	 For	update	information	on	Virtual	Remote	Tool,	visit	our	website:	
	 http://www.nec-display.com/dl/en/index.html
7. User Supportware  
						

							107
NOTE:
•	 When	[COMPUTER]	is	selected	from	your	source	selection,	the	Virtual	Remote	screen	or	the	toolbar	will	be	displayed	as	well	as	
your	computer	screen.
•	 Use	the	supplied	computer	cable	(VGA)	to	connect	the	COMPUTER	IN	terminal	directly	with	the	monitor	output	terminal	of	the	
computer	to	use	Virtual	Remote	Tool.
	 Using	a	switcher	or	other	cables	than	the	supplied	computer	cable	(VGA)	may	cause	failure	in	signal	communication.
	 VGA	cable	terminal:
	 Pin	Nos.	12	and	15	are	required	for	DDC/CI.
•	 Virtual	Remote	Tool	may	not	work	depending	on	your	computer’s	specifications	and	version	of	graphic	adapters	or	drivers.
•	 To	run	Virtual	Remote	Tool	on	Windows	8.1	and	Windows	8,	“Microsoft	.NET	Framework	Version	2.0”	is	required.	The	Microsoft	
.NET	Framework	Version	2.0,	3.0	or	3.5	is	available	from	Microsoft’s	web	page.	Download	and	install	it	on	your	computer.
•	 Logo	data	(graphics)	that	can	be	sent	to	the	projector	with	Virtual	Remote	Tool	has	the	following	restrictions:	
	 (Only	via	serial	connection)
-	 File	size:	Less	than	768	KB
-	 Image	size	(resolution):	
	P502H/P452H:	Horizontal	1920	×	vertical	1080	dots	or	less
	P502W/P452W:	Horizontal	1280	×	vertical	800	dots	or	less
TIP:
•	 The	projector’s	COMPUTER	IN	terminal	supports	DDC/CI	(Display	Data	Channel	Command	Interface).	DDC/CI	is	a	standard	
interface	for	bidirectional	communication	between	display/projector	and	computer.
•	 With	the	Virtual	Remote	Tool,	control	is	possible	with	both	network	(wired/wireless	LAN)	and	serial	connections.
Step 1: Install Virtual Remote Tool on the computer
NOTE:
•	 To	install	Virtual	Remote	Tool,	the	Windows	user	account	must	have	“Administrator”	privilege.	
•	 Exit	all	running	programs	before	installing	Virtual	Remote	Tool.	If	another	program	is	running,	the	installation	may	not	be	com-
pleted.	
2.  Go to the Dukane or NEC website for the latest Mac software. 
Visit:  www.dukaneav.com and go to the Service  page for downloads and links.
http://www.dukane.com/av/service/downloads.asp 
Or visit URL: http://www.nec-display.com/dl/en/index.html 
 
3.     Download - Projector → Virtual Remote Tool
6650HDA/6645HDA:
    6650WA/6645WA: 
7. User Supportware  
						

							108
3	 Click	“Next”.
	 “END	USER	LICENSE	AGREEMENT”	screen	will	be	displayed.
	 Read	“END	USER	LICENSE	AGREEMENT”	carefully.
4	 If	you	agree,	click	“I	accept	the	terms	in	the	license	agreement”	and	then	click	“Next”.
•	 Follow	the	instructions	on	the	installer	screens	to	complete	the	installation.
•	 When	the	installation	is	complete,	you	will	return	to	the	menu	window.
7. User Supportware  
						

							109
TIP:
Uninstalling	Virtual	Remote	Tool
Preparation:
Exit	Virtual	Remote	Tool	before	uninstalling.	To	uninstall	Virtual	Remote	Tool,	the	Windows	user	account	must	have	
“Administrator”	privilege	(Windows	8.1,	Windows	8,	Windows	7	and	Windows	Vista)	or	“Computer	Administrator”	
privilege	(Windows	XP).
•	For	Windows	8.1,	Windows	8,	Windows	7	and	Windows	Vista
1	 Click	“Start”	and	then	“Control	Panel”.
 The Control Panel window will be displayed.
2	 Click	“Uninstall	a	program”	under	“Programs”
	 The	“Programs	and	Features”	window	will	be	displayed.
3	 Select	Virtual	Remote	Tool	and	click	it.
4	 Click	“Uninstall/Change”	or	“Uninstall”.
	 •	When	the	“User	Account	Control”	windows	is	displayed,	click	“Continue”.
 Follow the instructions on the screens to complete the uninstallation.
Step 2: Connect the projector to the computer
1	 Use	the	supplied	computer	cable	(VGA)	to	connect	the	COMPUTER	IN	terminal	of	the	projector	directly	
with the monitor output terminal of the computer.
2	 Connect	the	supplied	power	cord	to	the	AC	IN	of	the	projector	and	the	wall	outlet.
 The projector is in the standby condition.
COMPUTER IN
AC	InputSupplied computer cable (VGA)
→ To wall outlet Power cord (supplied)
TIP:
•	 When	Virtual	Remote	Tool	starts	for	the	first	time,	“Easy	Setup”	window	will	be	displayed	to	navigate	your	connections.
7. User Supportware