Dukane Liquid Crystal Projector 28A8046 Users Manual

							ENGLISH-19
ENGLISH
TROUBLESHOOTING TROUBLESHOOTING
OSD Message
The messages as described below may appear on the screen at power ON. Take the appropriate
measures when such messages appears.
Table 9. OSD Messages
MessageContents
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
*1)
The lamp will reach the end of its life in 300 hours.
Power is switched OFF automatically when the lamp
reaches the end of its life. Prepare a new lamp for
installation.
Always reset the lamp timer after replacing the lamp.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL TURN OFF
AFTER 
**hr.*1)
The lamp will reach the end of its life in **hours.
Power will be switched OFF automatically in **hours.
Replace the lamp as shown in P.17~18 “Lamp”.
Always reset the lamp timer after replacing the lamp.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL 
TURN OFF
AFTER 0 hr.The lamp has reached the end of its life. Power will be
switched OFF in a few minutes.
Switch power OFF immediately and replace the lamp as
shown in P.17~18 “Lamp”.
Always reset the lamp timer after replacing the lamp.
NO INPUT IS DETECTED
ON ***No input signal found.
Check signal input connections and signal sources.
SYNC IS OUT OF RANGE
ON ***
The horizontal or vertical frequency of the input signal is
not within the specified range.
Check the specifications of the equipment and the signal
source.
CHECK THE AIR FLOW
The internal temperature has risen.
Switch power OFF, and wait 20 minutes until the
equipment cools.
Check the following and Switch power ON again.
• Are the ventilation openings blocked ?
• Is the air filter dirty ?
• Is the ambient temperature in excess of 35°C ?
*1) This message is cleared automatically after approximately three minutes, and appears
every time power is switched ON.NOTE 
						

							ENGLISH-20
T T T T
R R R R
O O O O
U U U U
B B B B
L L L L
E E E E
S S S S
H H H H
O O O O
O O O O
T T T T
I I I I
N N N N
G G G G
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Indicators Message
The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Take the
appropriate measures.
Table 10. Indicators Message
POWER
indicatorLAMP
indicator
TEMP
indicatorContents
Lights
orangeTurns offTurns offThe Standby mode has been set.
Blinks
greenTurns offTurns offWarming up. Please wait.
Lights
greenTurns offTurns offON. Normal operation possible.
Blinks
orangeTurns offTurns offCooling. Please wait.
Blinks red--Cooling. Please wait. 
The error is found. Take the appropriate measures when the
POWER indicator ceases blinking 
Blinks
/Lights redLights
redTurns off
Lamp is not lit.
The interior of the equipment may be too hot. Switch power OFF,
wait 20 minutes until the equipment cools, and check whether the
ventilation openings are  blocked, whether the air filter is dirty, or
whether the ambient temperature exceeds 35 °C. And switch
power ON again. Replace the lamp if the same problem occurs.
Blinks
/Lights redBlinks
redTurns off
Lamp or lamp cover is not found, or hasn’t been fitted in correctly.
Switch power OFF, and wait for 45 minutes until the equipment
cools. Check fitting of the lamp and lamp cover, and switch power
ON again. Contact your dealer if the same problem occurs again.
Blinks
/Lights redTurns offBlinks
redThe cooling fan is not operating.
Switch power OFF, and wait for 20 minutes until the equipment
cools. Check for foreign matters in the fan, and switch power ON
again. Contact your dealer if the same problem occurs again.
Blinks
/Lights redTurns offLights red
The interior of the equipment is too hot. *2)
Switch power OFF, and wait for 20 minutes until the equipment
cools. Check whether the ventilation openings are  blocked,
whether the air filter is dirty, or whether the ambient temperature
exceeds 35 °C. Then switch power ON again. Contact your dealer if
the same problem occurs again.
Lights
greenBlinks
redBlinks
redThe interior of the equipment is too cool.
Check whether the ambient temperature is below 0°C. Contact your
dealer if the same problem occurs when the ambient temperature is
0~35°C.
*2) When the internal temperature becomes excessive power is switched OFF
automatically for safety reasons, and the indicator is extinguished. Set the power switch to [
O] and
wait for 20 minutes until the equipment has cooled sufficiently.
NOTE 
						

							ENGLISH-21
ENGLISH
T T T T
R R R R
O O O O
U U U U
B B B B
L L L L
E E E E
S S S S
H H H H
O O O O
O O O O
T T T T
I I I I
N N N N
G G G G
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Symptom
Before requesting repair, check in accordance with the following chart. If the situation cannot be
corrected, then contact your dealer.
Table 11. Symptom
SymptomPossible causeRemedyPage
The power is not
turned on.
The main power switch is not
turned on.Turn on the main power switch.
7,8The power cord is
disconnected.Plug the power cord into an AC
power outlet.
No video or audio.The input is not correctly set.Use the projector or remote control
transmitter to set.9
No signal input.Connect correctly.6,7
Video is present but
no audio.
The projector is not correctly
connected.Connect correctly.6,7
The volume is set to minimum.Press VOLUME  on the remote
control or display the menu screen
and adjust the volume.10,14
Mute is turned on.Press the MUTE button.10
Audio is present but
no video.
The projector is not correctly
connected.Connect correctly.6,7
The brightness is set to
minimum.Select BRIGHT with the MENU
button and the press the  button.11
The slide lens door is still
closed.Open the slide lens door.8
Colors are pale and
color matching is
poor.Color density and color
matching are not correctly
adjusted.Adjust the video.11
Images are dark.
Brightness and contrast are not
correctly adjusted.Adjust the video.11
The lamp is nearing the end of
its service life.Replace with a new lamp.16,17
Images are blurred.Focus or H PHASE is out of
adjustment.Adjust the focus or H PHASE.8,11 
						

							ENGLISH-22
SPECIFICATIONS SPECIFICATIONS
Table 12. Specifications
•
This specifications are subject to change without notice.NOTE
ItemSpecification
Product nameLiquid crystal projector
Liquid
crystal
panelPanel size1.8 cm (0.7 type)
Drive systemTFT active matrix
Pixels480,000 pixels (800 horizontal x 600 vertical)
LensZoom lens F=2.0 ~ 2.3  f=18 ~ 21 mm
Lamp150 W UHB
Speaker1.2 W
Power supplyAC100 ~ 120V, 2.7A / AC220 ~ 240V, 1.3A
Power consumption240 W
Temperature range0 ~ 35°C (Operating)
Size289 (W) x 84 (H) x 215 (D) mm
Weight (mass)2.4 kg
RGB
signal
inputRGB IN
Video: Analog 0.7Vp-p, 75Ωterminator (positive)
H/V. sync.: TTL level (positive/negative)
Composite sync.: TTL level
D-sub 15-pin shrink jack
AUDIO IN200mVrms, 47 kΩ(max. 3.0Vp-p)
Stereo mini jack
Video
signal
input
VIDEO1.0Vp-p, 75Ωterminator
RCA jack
S-VIDEOBrightness signal: 1.0Vp-p, 75Ωterminator
Color signal: 0.3Vp-p (burst signal), 75Ωterminator
Mini DIN 4-pin jack
COMPONENT
VIDEOY1.0 Vp-p, 75 ΩTerminator (Positive)
CB/CR0.7 Vp-p, 75 ΩTerminator (Positive)
PB/PR0.7 Vp-p, 75 ΩTerminator (Positive)
AUDIOL200mVrms, 47 kΩ(max. 3.0Vp-p)
RCA jack
R
Control
functionsCONTROLD-sub 15-pin shrink plug
Optional PartsLamp: DT00401
Air Filter: MU01461
* For others, consult your dealer. 
						

							ENGLISH-23
ENGLISH
WARRANTY AND AFTER-SERVICE WARRANTY AND AFTER-SERVICE
If a problem occurs with the equipment, first refer to the P.20 “TROUBLESHOOTING” section and
run through the suggested checks. If this does not resolve the problem contact your dealer or service
company. They will tell you what warranty condition is applied. 
						

							Pin NoSignalPin NoSignalPin NoSignal
1Video input Red9-
15
RGB IN 1:  SCL(DDC)
2Video input Green10GroundRGB IN 2:   -
3Video input Blue11-RGB OUT:   -
4-
12
RGB IN 1: SDA(DDC)
5GroundRGB IN 2:   -
6Ground RedRGB OUT:   -
7Ground Green13H. sync./ Composite sync.
8Ground Blue14Vertical sync
TECHNICAL - 1
TECHNICAL TECHNICAL
TECHNICAL
Dimension Diagram
289
84
52.5
74.5
215
60
Unit : mm
2. Mini Din 4-pin Connector (S-VIDEO)
Pin NoSignal
1Color:0.286Vp-p (NTSC, burst signal),75Ωterminator
0.3Vp-p (PAL/SECAM, burst signal),75Ωterminator
2Brightness:1.0Vp-p, 75Ωterminator
3Ground
4Ground
Signal Connector Pin Assignment
1. D-sub 15-pin Shrink Connector (RGB IN)
1 2 3
4 5
6
7 8 9
10
11 12 13
14 15 
						

							TECHNICAL - 2
T T T T
E E E E
C C C C
H H H H
N N N N
I I I I
C C C C
A A A A
L L L L(
( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Example of computer signal
Resolution 
H × ×
VfH (kHz)fV (Hz)RatingSignal modeDisplay
mode
720 ×40037.985.0VESATEXTZoom in
640 ×48031.559.9VESAVGA (60Hz)Zoom in
640 ×48035.066.7Mac13modeZoom in
640 ×48037.972.8VESAVGA (72Hz)Zoom in
640 ×48037.575.0VESAVGA (75Hz)Zoom in
640 ×48043.385.0VESAVGA (85Hz)Zoom in
800 ×60035.256.3VESASVGA (56Hz)
800 ×60037.960.3VESASVGA (60Hz)
800 ×60048.172.2VESASVGA (72Hz)
800 ×60046.975.0VESASVGA (75Hz)
800 ×60053.785.1VESASVGA (85Hz)
832 ×62449.774.5Mac16modeZoom out
1024 ×76848.460.0VESAXGA (60Hz)Zoom out
1024 ×76856.570.1VESAXGA (70Hz)Zoom out
1024 ×76860.075.0VESAXGA (75Hz)Zoom out
1024 ×76868.785.0VESAXGA (85Hz)Zoom out
1152 ×86467.575.0VESASXGA (75Hz)Zoom out
1280 ×96060.060.0VESASXGA (60Hz)Zoom out
1280 ×102464.060.0VESASXGA (60Hz)Zoom out
•Some computers may have multiple display screen modes. Use of some of these modes
will not be possible with this projector.
• Be sure to check jack type, signal level, timing and resolution before connecting this projector to a
computer.
• Depending on the input signal, full-size display may not be possible in some cases. Refer to the
number of display pixels above.
• The image might be something wrong with computer by computer on the digital RGB mode. In
this case, it is recommended to reduce the resolution and / or reflesh rate.NOTE 
						

							TECHNICAL - 3
TECHNICAL
T T T T
E E E E
C C C C
H H H H
N N N N
I I I I
C C C C
A A A A
L L L L(
( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Initial set signals
The following signals are used for the initial settings.
The signal timing of some computer models may be different. In such case, refer to adjust the
V.POSIT and H.POSIT of the menu.
DATA
HSYNCDATA
VSYNCDisplay interval c
Back porch b
Sync aFront porch d
Display interval c
Back porch b
Sync aFront porch d
Computer /
SignalHorizontal signal timing (µs)
abcd
TEXT2.03.020.31.0
VGA (60Hz)3.81.925.40.6
Mac 13mode2.13.221.22.1
VGA (72Hz)1.33.820.31.0
VGA (75Hz)2.03.820.30.5
VGA (85Hz)1.62.217.81.6
SVGA (56Hz)2.03.622.20.7
SVGA (60Hz)3.22.220.01.0
SVGA (72Hz)2.41.316.01.1
SVGA (75Hz)1.63.216.20.3
SVGA (85Hz)1.12.714.20.6
Mac 16mode1.13.914.50.6
XGA (60Hz)2.12.515.80.4
XGA (70Hz)1.81.913.70.3
XGA (75Hz)1.22.213.00.2
XGA (85Hz)1.02.210.80.5
1152×864 (75Hz)1.22.410.70.6
1280×960 (60Hz)1.02.911.90.9
1280×1024 (60Hz)1.02.311.90.4
Computer /
SignalVertical signal timimg (lines)
abcd
TEXT3424001
VGA (60Hz)23348010
Mac 13mode3394803
VGA (72Hz)3284809
VGA (75Hz)3164801
VGA (85Hz)3254801
SVGA (56Hz)2226001
SVGA (60Hz)4236001
SVGA (72Hz)62360037
SVGA (75Hz)3216001
SVGA (85Hz)3276001
Mac 16mode3396241
XGA (60Hz)6297683
XGA (70Hz)6297683
XGA (75Hz)3287681
XGA (85Hz)3367681
1152×864 (75Hz)3328641
1280×960 (60Hz)3369601
1280×1024 (60Hz)33810241 
						

							TECHNICAL - 4
T T T T
E E E E
C C C C
H H H H
N N N N
I I I I
C C C C
A A A A
L L L L(
( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Connection to the Mouse Control
1. PS/2, ADB or Serial Mouse
(1) Turn off the projector and computer, and connect the two units with the appropriate cable. For
PS/2 mouse control (for IBM and compatible), use the enclosed mouse cable. For others, consult
your dealer.
(2) Disconnect the USB cable from the projector if it is connected. Then turn on the projector.
(3) Turn on the computer.
(4) 
Start the mouse function. If the mouse has not been started, reboot the computer (soft reboot or
reboot buttons). Refer to the descriptions of “DISC PAD” and “MOUSE/RIGHT button” of page 4.
2. USB Mouse
(1) Connect the projector and computer with a suitable commercially available USB cable. Consult
your dealer to get the cable, if you need.
(2) Start the mouse function. Refer to the descriptions of “DISC PAD” and “MOUSE/RIGHT
button” of page 4.
• Before connecting, read the instruction manuals of the devices to be connected. 
• In the case of notebook type computers with an internal pointing device, the mouse control
function will not work unless the internal pointing device is disabled. In such case, disable the
internal pointing device and change the BIOS setting to select an external mouse before the
operations described in (1) to (4) above. 
Also, some computers may not have a utility program to operate a mouse. 
Refer to the computer hardware manual for detail.
NOTE
PS/2 Mouse
2
1
4
3
6
5
2
1
4
3
6
5
8
7
10
9
12
11
14
13
15
CLK
D ATA
SEL0
RTS
GND+5VD ATA
GND
+5V
CLK
21
43
65
Mouse jack 
Mini DIN 6-pin Projector
Computer
123
4
5
6
78
910
11 12
13
14
15
CONTROL Terminal
D-sub 15-pin shrink jack