Dukane Imagepro 9015 D-ila Projector Instructions

11
ENGLISH
Controls and Features (cont.)
Connector Panel
1Y/C (S video) input terminal (Mini DIN 4 pin)
Connect this terminal to the S video output terminal of a
video deck, etc.
2VIDEO (composite video) input terminal (BNC)
Connect this terminal to the composite video output terminal
of a video deck, etc.
3Y,  PB/B-Y, PR/R-Y input terminals (BNC)
These are input terminals for component (Y, B-Y, R-Y)
signals or DTV-format (Y, P
B, PR) signals.
Device with component output terminals can be
connected.
*...

12
Controls and Features (cont.)
Connector Panel (Cont.)
9COMPUTER IN (computer input) -2 terminal (BNC)
These are input terminals for analog RGB signals, vertical
sync (V) signals, and horizontal sync (H) signals /
composite signals(Cs). Devices which have analog RGB
signal output terminals can be connected.
 * Input of external sync signals is automatically
detected.
Detection of H/V signals or Cs signals causes automatic
switch to external sync. The priority order is H/V > Cs.
Note
¥ DTV-format (480i,...

13
ENGLISH
Controls and Features (Cont.)
Remote Control Unit
1Remote controlÕs signal transmitter
2COMPUTER button
Use this button to select the devices connected to the
projectorÕs COMPUTER IN (computer input) -1 and -2 input
terminals. Each time you press the button, the selection
changes as follows:
COMPUTER 1
COMPUTER 2
3VIDEO button
Use this button to select the devices such as a video
connected to the projectorÕs AV IN (AV input) terminal. Each
time you press the button, the selection changes as...

14
Controls and Features (cont.)
Installing Batteries
Install batteries in the remote control. If the remote control has started to work erratically, replace the batteries.
1Open the back cover.
While pushing on the back cover, slide it in the direction
of the arrow.
2Install the batteries.
Place the two batteries (AAA/R03-size) supplied in the
remote control as illustrated below.
3Close the back cover.
Slide the back cover in the direction of the arrow until a
click is heard.
Precautions for using...

15
ENGLISH
Installing the Projector
Precautions for Installation
nWhen installing the projector, observe the followings:
¥ Do not use the projector placed on its side.
Avoid using the projector placed on its side. This could cause a malfunction.
¥ Use the projector within the installed angle.
Avoid using the projector inclined ±30° or more right-to-left or left-to-right. This could cause color variation or harm the lamp
life.
¥ Do not block the exhaust vents.
Do not use a cover which encloses the...

16
Installing the Projector (Cont.)
Projection Distance and Screen Size
nThe projectorÕs projection lens is a zoom lens of about 1.5 x. The screen size at the maximum enlargement is 1.5
times that of the minimum size.
nThe projection distance that can be focused is 2.5 to 20 m. Install the projector within this range.
Screen
Install the projector so the lower
edge of the projection screen is
at the same height as the lensÕ
center line.Screen with 4 : 3 aspect ratio
nChange of projection screen
according...

17
ENGLISH
Installing the Projector (Cont.)
Relationship between Projection Distances and Projection Screen Sizes
nFor 4 : 3 aspect ratio screens
8.2 ft (2.5 m) 42Ó (approx. 107 cm) 63Ó (approx. 160 cm)
9.84 ft (3.0 m) 51Ó (approx. 130 cm) 76Ó (approx. 193 cm)
13.12 ft (4.0 m) 68Ó (approx. 173 cm) 102Ó (approx. 259 cm)
16.4 ft (5.0 m) 86Ó (approx. 219 cm) 128Ó (approx. 325 cm)
19.68 ft (6.0 m) 103Ó (approx. 262 cm) 154Ó (approx. 391 cm)
22.96 ft (7.0 m) 120Ó (approx. 305 cm) 180Ó (approx. 457 cm)
26.24...

18
Installing the Projector (Cont.)
Effective Range and Distance of the Remote Control Unit
The operable distance of the remote control unit is about 10 m (32.8 ft\
) for direct reception. The remote control can be used by
having it reflected on the screen, etc. When you use the remote control \
by reflecting it at the screen, the total distance of A  + B
should be about 10 m (32.8 ft) or less. The operable angles of the remote control unit is 50 ° right to left, and 15 ° up and down.
The effective...

19
ENGLISH
Connecting to Various Devices
The following signals can be input to the projector:
nVideo signals
(1) Response to color systems
*
1 : Responds if Y/C output is available.
*
2 : Signifies that component signals (ÒY, PB, PR Ó / Ò Y, B-Y, R-YÓ / ÒG, B, R, H/CS, VÓ) conform to the signal timing (synchroniza-
tion and video period) of each color system. The color systems are used for convenience only.
(2) Response to double density (*1), high-vision signals
Color system
NTSC NTSC4.43 PAL SECAMInput...

20
YAUDIO
AUDIO OUT
REMOTEY/C
VIDEO
Y
P
B/B-Y
P
R/R-Y L
R
RS-232C
Memo
¥ When connecting a video device, use a TBC along with it, or one
which has a built-in TBC.
¥ Use of an extension cable to connect a video device and the
projector could cause video degradation.
¥ When a signal with much jitter is reproduced on a VCR or special-
effect playback is performed, the upper part of the picture or the
picture itself may be erased or distorted.
Connecting to Various Devices (Cont.)
Connecting to Video...