Dukane Imagepro 8945 Users Guide

41
SETTING
Lamp counter reset
Move pointer to Lamp counter reset and then
press SELECT button.  
Move arrow to
replaced lamp number (Lamp 1 or Lamp
2) and then press 
SELECT button.
USB
Projector mode
Select   when controlling a projector with computer.
NOTE:Before you control a projector by computer, install USB driver
(optionally sold parts) and set up computer following instruc-
tion in USB driver package. Contact your authorized dealer.
This Projector is equipped with USB port for interactive...

42
APPENDIX
OPERATING WIRELESS MOUSE
INSTALLATION
Wireless Remote Control Unit is not only able to operate this projector but also usable as a wireless mouse for most
Personal Computers.  POINT buttons and two CLICK buttons are used for wireless mouse operation.
This Wireless Mouse function is available only when PC mouse pointer is displayed on a projected screen.  When ON-
SCREEN MENU or any message / dialog box is displayed on screen instead of PC mouse pointer, this Wireless Mouse
function cannot be...

43
APPENDIX
E
AIR FILTER CARE AND CLEANING
Turn power off, and disconnect AC power cord from
an AC outlet.1
2
Air Filter prevents dust from accumulating on a surface of Projection Lens and Projection  Mirror.  Should Air
Filter become clogged with dust particles, it will reduce Cooling Fans effectiveness and may result in internal
heat build up and adversely affect life of  projector.
Clean Air Filter following steps below: 
3
4
CAUTION
Do not operate a projector with Air Filter
removed.  Dust may...

44
APPENDIX
LAMP MANAGEMENT
This Projector is equipped with 2 Projection Lamps to ensure brighter image and those lamps are controlled by Lamp
Management Function.  Lamp Management Function detects status of two lamps and shows status on screen or on LAMP
REPLACE indicator.  This function also automatically controls Lamp Mode when any of lamps is out for end of life or
malfunctions. 
Lamp Status Display
Lamp Status Display appears on screen when power switch is on or changed input position (input 1,...

45
APPENDIX
Check number of lamp to be replaced on Lamp Status 
Display.
Loosen 3 screws on Lamp Cover and remove Lamp Cover. 
(See right figure.)
1
3
Loosen 2 screws and pull out Lamp Assembly to be replaced 
by grasping handle.4
Turn off a projector and disconnect AC Power Cord.  Allow a 
projector to cool for at least 45 minutes.2
Replace Lamp Assembly with a new one and tighten 2 screws. 
Make sure that Lamp Assembly is set properly
6
Follow these steps to replace lamp assembly.
Replace Lamp Cover...

Check audio cable connection from audio input source.
Adjust audio source.
Press VOLUME (+) button.
Press MUTE button.
46
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check matters below once again.
1. Make sure you have connected a projector to your computer or video equipment as described in section CONNECTING
PROJECTOR  on pages 12 ~ 15.
2. Check cable connection.  Verify that all computer, video and power cord are properly connected.
3. Verify that all...

Check cable connection between a projector and your computer.
 Check mouse setting on your computer.
 Turn a projector on before turning on a computer.
47
APPENDIX
This symbol on the nameplate means the product is Listed by Underwriters\
 
Laboratories Inc.  It is designed and manufactured to meet rigid U.L. sa\
fety
standards against risk of fire, casualty and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (E\
C).
Remote Control Unit 
does not work.Check...

Accessories
48
APPENDIX
Specifications are subject to change without notice.
TECHNICAL SPECIFICATIONS
1.8 TFT Active Matrix type, 3 panels
Multi-media Projector
45.2 lbs (20.5 kg)
17.3 x 9.1 x 23.8 (439 mm x 230 mm x 605.6 mm) 
1280 x 1024  (28A9058) 1024 x 768 (28A8945) 
3,932,160 (1280 x 1024 ) 2,359,296  (1024 x 768) 3 panels
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
Up and Down
800 TV lines
INT. SP. Stereo (R and L), 3 watt RMS (T.H.D. 10%)
41 ˚F ~ 95  ˚F (5  ˚C ~ 35  ˚C)
14  ˚F ~ 140  ˚F (-10  ˚C...

49
APPENDIX
CONFIGURATIONS OF TERMINALS
Terminal : Mini DIN 8-PIN
Connect control port (PS/2, Serial or ADB port) on your computer to this terminal with Control Cable (supplied).
12
345876
Pin Configuration
CONTROL PORT CONNECTOR
-----
CLK
DATA
GND
-----
-----
GND
-----
R X D
-----
-----
GND
RTS
T X D
GND
GND
-----
ADB
-----
GND
-----
-----
-----
GND
PS/2SerialADB
1
2
3
4
5
6
7
8
DVI-I TERMINAL (DIGITAL/ANALOG) 
This terminal accepts only Digital (TMDS) or Analog (RGB) output signal. Connect display...

LEGAL INFORMATION
FIVE-YEAR LIMITED  WARRANTY 
This Dukane LCD projector is warranted to the original purchaser for a p\
eriod of 
five (5) years from the original purchase date - in normal use and ser\
vice -
against defects in material and workmanship. DUKANE CORPORA TION
EXPRESSLY DISCLAIMS  ALL OTHER W ARRANTIES OF MERCHANT ABILITY
AND FITNESS FOR A P AR TICULAR PURPOSE.
During the warranty period, Dukane Corporation will repair or replace (\
at the
manufacturers option) any such defective parts...