Dukane Imagepro 8932 Lcd Projector Users Guide

21
To adjust the height of the projector, press and hold the elevator 
button, raise the projector to the desired height, then release the 
button to lock the foot into position. Rotate the leveling knob, if 
necessary, to adjust the angle of the projected image.
FIGURE 17
Adjusting the height of the projector
F
IGURE 18
Leveling knob
elevator button
elevator foot
LL
In outIn In L BNCBNC
RR R
A
0A
0
R s
R
G G
B B
leveling knob 

22
Using the Projector
Using the Remote Control
NOTE: If you can’t aim the
remote control at the projector so
that its signal is received 
— for
example, when using rear projection or in a large
auditorium
— connect it directly to
the projector with the optional remote control cable.
To control the computer ’s mouse from the projector ’s remote or  
keypad, you must connect either the USB connector on the M1 
computer cable to the computer (see page 12) or a type B USB  
mouse cable to your computer and...

23
Press anywhere on the edge of the disk mouse to move the cursor 
on the screen. You can move the cursor at any angle by pressing 
the corresponding edge of the disk. The mouse button on the top 
of the remote simulates your computer ’s right mouse button; the 
button on the bottom simulates your computer ’s left mouse but-
ton. When you press the disk mouse, the remote lights up. The 
light goes off about 10 seconds after you stop pressing buttons. 
To use the laser pointer, press and hold the laser...

24
Using the Projector
Using the Keypad and Remote Buttons
While the menus are displayed, the volume, source, and standby 
buttons on the keypad act as menu navigation buttons. See 
“Using the On-Screen Menus” on page 27 for details.
FIGURE 20
Keypad buttons
F
IGURE 21
Remote buttons
source
standbyvolume + volume -menu power
right mouse
button left mouse
button 

25
Brightness + or - (remote only)
Adjusting the brightness lightens or darkens the image.
To darken the image, press 
-.

To lighten the image, press 
+.
Freeze (remote only) 
The freeze button halts, or “freezes” the projected image. Use this 
button to freeze a frame of video (the video continues to run but 
the projected image is frozen). You can also freeze an image from 
a computer source on the screen, allowing you to perform other 
operations on the computer without the audience seeing them....

26
Using the Projector
Standby  
When you press standby, the display and audio turn off and a 
blank screen is displayed for 15 minutes. You can change the 
amount of time the projector stays in standby mode; see 
“Standby Time” on page 35 for details. While the projector is in 
standby, the keypad and remote buttons do not affect the projec-
tor and the LED lights orange.
If you press standby again within the standby time, the projec-
tor returns to normal operations immediately.
If you don’t press...

27
Using the On-Screen Menus
The projector
 has six drop-down menus that allow you to make 
image adjustments and change a variety of settings. Most of these 
adjustments aren’t available directly from the keypad. 
NOTE: Some menu items may be 
grayed out at certain times. This 
indicates the item is not applicable 
to your setup (for example, video 
standards do not apply to com-
puter sources) or the item is not 
enabled until another selection is 
made (for example, Manual Track-
ing is not available...

28
Using the Projector
Display Menu 
 
FIGURE 23
Display menu
Brightness
Adjusting the brightness changes the intensity of the image.
Press the left mouse button to darken the image.
Press the right mouse button to lighten the image.
Contrast
The contrast controls the degree of difference between the lightest 
and darkest parts of the picture. Adjusting the contrast changes 
the amount of black and white in the image.
Press the left mouse button to decrease the contrast.
Press the right mouse button...

29
Color
The color setting adjusts a video image from black and white to 
fully saturated color.
Press the left mouse button to decrease the amount of color in 
the image.
Press the right mouse button to increase the amount of color in 
the image.
Color Temperature
The Color Temperature setting adjusts the amount of red in the 
projected image. 
Press the left mouse button to decrease the amount of red in the 
image.
Press the right mouse button to increase the amount of red in 
the image.
Sharpness...

30
Using the Projector
Audio Menu
 
FIGURE 24
Audio menu
Vo l u m e
NOTE: Changing the volume
using the menu is the same as
changing it using the remote or
keypad.
Press the left mouse button to decrease the volume. 
Press the right mouse button to increase the volume.
Volume adjustments you make are saved for each source.
Tr e b l e
The treble setting controls the high frequencies of your audio 
source.
Press the left mouse button to decrease the treble. 
Press the right mouse button to increase the...