Dukane Imagepro 8930 Projector Users Manual

							71
NETWORK menu
ItemDescription
WIRELESS 
INFORMATION "Selecting this item displays the WIRELESS_INFORMATION dialog 
for viewing the wireless LAN settings." Use the ▲/▼ buttons to 
switch the page.
The first page shows the wireless LAN settings. The second and 
subsequent pages display the signal information of wireless LAN 
connection devices.
• For details of PASSCODE, refer to the manual for “LiveViewer”
. 
• Nothing (blank) is shown in the PROJECTOR NAME  (
74)
 and 
SSID  (70)
 field until you setup those items. Only the first 16  
characters of the PROJECTOR NAME.
• IP ADDRESS, SUBNET MASK and DEFAULT GATEWAY indicate 
“0.0.0.0” in the following condition.
(1) The USB wireless adapter is not inserted into the projector.
(2) DHCP is ON and the projector does not get address from DHCP 
server.
• Nothing (blank) is shown in the CH and SPEED fields if the USB 
wireless adapter is not inserted.
• The actual performance and setting will be shown in the CH field, 
instead of the setting value in the WIRELESS SETUP menu.
• An icon is displayed to the left of the SSID of the device connected 
to the projector.
(continued on next page) 
						

							72
NETWORK menu
ItemDescription
WIRED SETUP Selecting this item displays the WIRED 
SETUP menu for the wired LAN.
Use the ▲/▼ buttons to select an item, 
and the ► or ENTER button on the remote 
control to perform the item.
DHCP  
(Dynamic Host  Configuration  Protocol) Use the ▲/▼ buttons to turn DHCP on/off.
ON  ó OFF
Select OFF when the network does not have 
DHCP enabled. To save the setting, press the ► 
button.
• When the “DHCP” setting changes to “ON”, it 
takes a little time to obtain IP address from DHCP 
server.
• Auto IP function will be assigned an IP address if 
the projector could not obtain an IP address from 
server even if DHCP is “ON”.
IP ADDRESS Use the ▲/▼/◄/► buttons to enter the IP 
ADDRESS. 
This function can only be used when DHCP is set 
to OFF.
• The IP ADDRESS is the number that identifies 
this projector on the network. You cannot have two 
devices with the same IP ADDRESS on the same 
network.
• The IP ADDRESS “0.0.0.0” is prohibited.
SUBNET  MASK Use the ▲/▼/◄/► buttons to enter the same 
SUBNET MASK used by your computer. 
This function can only be used when DHCP is set 
to OFF.
• The SUBNET MASK “0.0.0.0” is prohibited.
DEFAULT 
GATEWAY Use the ▲/▼/◄/► buttons to enter the DEFAULT 
GATEWAY (a node on a computer network that 
serves as an access point to another network) 
address.
This function can only be used when DHCP is set 
to OFF.
DNS SERVER Use the ▲/▼/◄/► buttons to input the DNS 
server address. 
The DNS server is a system to control domain 
names and IP addresses on the Network. 
(continued on next page) 
						

							73
NETWORK menu
ItemDescription
WIRED SETUP (continued) TIME 
DIFFERENCE Use the ▲/▼ buttons to enter the TIME 
DIFFERENCE. 
Set the same TIME DIFFERENCE as the one 
set on your computer. If unsure, consult your IT 
manager. 
Use the ► button to return to the menu after 
setting the TIME DIFFERENCE.
• When this item is set, the same item in the 
WIRELESS SETUP menu is overwritten with the 
same setting (

68).
DATE AND  TIME Use the ▲/▼/◄/► buttons to enter the Year (last 
two digits), Month, Date, Hour and Minute.
• When this item is set, the same item in the 
WIRELESS SETUP menu is overwritten with the 
same setting (

69).
• The projector will override this setting and retrieve 
DATE AND TIME information from the Time server 
when SNTP is enabled.  (Date/Time Settings in 
the Network Guide)
• This setting will be reset if the projector is turned 
off while STANDBY MODE in the SETUP menu 
is set to SAVING (
 48), or when the AC power is 
turned off.
WIRED 
INFORMATION Selecting this item displays the WIRED INFORMATION dialog for 
viewing the wired LAN settings.
• For details of PASSCODE, refer to the manual for “LiveViewer”.
• Only the first 16 characters of the PROJECTOR NAME are dis-
played.
• IP ADDRESS, SUBNET MASK and DEFAULT GATEWAY indicate 
“0.0.0.0” when DHCP is ON and the projector has not gotten address 
from DHCP server.
(continued on next page) 
						

							74
NETWORK menu
ItemDescription
PROJECTOR  NAME (1)  
Use the ▲/▼ buttons on the 
NETWORK menu to select the 
PROJECTOR NAME and press 
the ► button. The PROJECTOR 
NAME dialog will be displayed.
(2)    The current PROJECTOR NAME will be displayed on the first 3 
lines. Particular projector name is pre-assigned by default.
Use the ▲/▼/◄/► buttons and the  ENTER or INPUT button to 
select and enter characters.
To erase 1 character at one time, press the  RESET button or 
press the ◄ and INPUT button at the same time. Also if you 
move the cursor to DELETE or ALL CLEAR on screen and 
push the ENTER or INPUT button, 1 character or all characters 
will be erased.The PROJECTOR NAME can be input up to 64 
characters.
(3)    To change an already inserted 
character, press the ▲/▼ button 
to move the cursor to one of the 
first 3 lines, and use the ◄/► 
buttons to move the cursor on the 
character to be changed. After 
pressing the  ENTER or INPUT 
button, the character is selected. 
Then, follow the same procedure 
as described at the item (2) above.
(4)    To finish entering text, move the cursor to the OK on screen and 
press the ►, ENTER or INPUT button. To revert to the previous 
PROJECTOR NAME without saving changes, move the cursor 
to the CANCEL on screen and press the ◄, ENTER or INPUT 
button.
(continued on next page) 
						

							75
NETWORK menu
ItemDescription
MY IMAGE Selecting this item displays the MY 
IMAGE menu. 
Use the application to transfer the im-
age data. It can be downloaded from 
the Hitachi web site.
Use the ▲/▼ buttons to select an item which is a still image by the 
MY IMAGE (My Image Function in the Network Guide) and the ► 
or ENTER button to display the image.
• The item without image stored cannot be selected.
• The image names are each displayed in 16 characters or less.
To switch the image displayed 
Use the ▲/▼ buttons.
To return to the menu Press the ◄ button on the remote control.
To erase the image displayed and its source file in the projector.(1)   Press the RESET button on the remote 
control while displaying an image to display 
the MY IMAGE DELETE menu. 
(2)   Press the ► button to perform to erase. 
To stop erasing, press the ◄ button.
AMX D.D.
(AMX Device  Discovery)
Use the ▲/▼ buttons to turn the AMX Device Discovery on/off.
ON  ó OFF
When ON is selected, the projector can be detected by  controllers 
of AMX connected to the same network. For the details of AMX 
Device Discovery, visit the AMX web site. URL: http://www.amx.com/  (as of Dec. 2011)
(continued on next page) 
						

							76
NETWORK menu
ItemDescription
PRESENTATION Selecting this item displays the PRESENTATION menu.
Use ▲/▼ buttons to select one of the following items, then press ► 
or ENTER button to use the function.
• To use Network Presentation, an exclusive application, "LiveViewer" 
is required. It can be installed from the bundled application CD. 
You can also download the latest version and relevant information 
from the Hitachi website (http://www.hitachi-america.us/digitalmedia 
or http://www.hitachidigitalmedia.com).For details of Network 
Presentation and instructions to install the "LiveViewer", refer to the 
manual for "LiveViewer".
QUIT 
PRESENTER  MODE
If you set a computer to the Presenter mode while 
its image is projected, the projector is occupied by 
the computer and access from any other computer is 
blocked.
Use this function to quit the Presenter mode and 
allow other computers to access the projector.
Select this item to display a dialog.
Press ► button to choose OK in the dialog.  
The Presenter mode is cancelled and a message is 
displayed indicating the result.
• To make Presenter mode setting, use “LiveViewer”.
For details, refer to the manual for "LiveViewer".
MULTI PC MODE
If you set one or more computers to the Multi PC 
mode on “LiveViewer” and send their images to the 
projector, you can select the display mode on the 
projector from two options below. 
-  Single PC mode: displays the image of the selected 
computer on full screen.
-   Multi PC mode: displays the images sent from up to 
four computers on screen that is divided into quarter 
sections.
Select this item to display a dialog. 
Use the dialog to change the display mode as 
explained below.
• To change from Multi PC mode to Single PC mode, 
select one of computers in the dialog using the 
▲/▼/◄/► buttons and press the  ENTER or INPUT 
button.
Press the ► button to choose OK, and then press 
ENTER or INPUT again. The image for the selected 
computer is displayed on full screen.
(continued on next page)
(continued on next page) 
						

							77
NETWORK menu
ItemDescription
PRESENTATION (continued) MULTI PC 
MODE
(continued) • To change from Single PC mode to Multi PC mode, 
press ► button to choose OK in the dialog and press 
the ENTER or INPUT button.
The display mode is changed.
• 
For details on how to switch the 
display mode to Multi PC mode 
on your computer, refer to the 
manual for 
“LiveViewer”.• The Presenter mode setting of the selected 
computer becomes valid when the display mode is 
changed to Single PC mode.  
Also, the Presenter mode setting  
becomes invalid when the  
display mode is changed to Multi  
PC mode, regardless the setting  
on the computers.
For details, refer to the manual for “LiveViewer” .
DISPLAY 
USER NAME Selecting this item displays the user name. This 
function helps you identify from which computer the 
current image is sent.
• You can set user names for each computer on 
“LiveViewer”. For details, refer to the manual for 
“LiveViewer”
.
SERVICE Executing this item restarts and initializes the network functions.
Choose the NETWORK RESTART EXECUTE using the button ►.
Then use the button ► to execute.
Network will be once cut off when choose restart.
If DHCP is selected on, IP address may be changed.
After selecting NETWORK RESTART EXECUTE, NETWORK menu 
may not be controlled approx. 30 seconds. 
						

							78
SECURITY menu
(continued on next page) This projector is equipped with security functions.
From the SECURITY menu, items shown in the table 
below can be performed.
To use SECURITY menu: User registration is required 
before using the security functions.
Enter to the SECURITY menu
1.  Press the ► button. The ENTER PASSWORD box will be displayed.  
2. 
 Use the ▲/▼/◄/► buttons to enter the registered password. 
    The factory default password is as follows.
  
               
    This password can be changed 
( below). Move the cursor to
    the right side of the ENTER PASSWORD box and press 
    the ► button to display the SECURITY menu. • It is strongly recommended the factory default password to be 
changed as soon as possible.
• If an incorrect password is input, the ENTER PASSWORD box 
will be displayed again. If incorrect password is input 3 times, the 
projector will turn off. Afterwards the projector will turn off every time 
an incorrect password is input.
3. 
 Items shown in the table below can be performed.
If you have forgotten your password(1)  While the ENTER PASSWORD box is displayed, press and hold the 
RESET button on the remote control for about 3 seconds or press 
and hold the  INPUT button for 3 seconds while pressing the ► 
button on the projector.
(2) 
 The 10 digit Inquiring Code will be displayed. Contact your dealer   
with the 10 digit Inquiring Code. Your password will be sent after your user registration information 
is confirmed.
• If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will 
close. If necessary, repeat the process from (1). 
 
Item Description
SECURITY 
PASSWORD  CHANGE
(1)  Use the ▲/▼ buttons on the SECURITY menu 
to select SECURITY PASSWORD CHANGE 
and press the ► button to display the ENTER 
NEW PASSWORD box.
(2) 
 Use the ▲/▼/◄/► buttons to enter the new password.
(3)  Move the cursor to the right side of the 
ENTER NEW PASSWORD box and press the 
► button to display the NEW PASSWORD 
AGAIN box, enter the same password again. 
(4) 
 Move the cursor to the right side of the NEW 
PASSWORD AGAIN box and press the ► 
button and the NOTE NEW PASSWORD box 
will be displayed for about 30 seconds, please 
make note of the password during this time.
Pressing the ENTER button on the remote control or ► button on the 
projector will close the NOTE NEW PASSWORD box.
• Please do not forget your password.
SECURITY menu
8755N, 8928, 8930, 8937:  3892
8929W, 8931W: 2292 
						

							79
SECURITY menu
ItemDescription
MyScreen 
PASSWORD
The MyScreen PASSWORD function can be used to prohibit access to the 
MyScreen function and prevent the currently registered MyScreen image 
from being overwritten.
1 Turning on the MyScreen PASSWORD1-1   Use the ▲/▼ buttons on the SECURITY menu to 
select MyScreen PASSWORD and press the ► 
button to display the MyScreen PASSWORD on/
off menu.
1-2   Use the ▲/▼ buttons on the MyScreen 
PASSWORD on/off menu to select ON. 
The ENTER NEW PASSWORD box (small) 
will be displayed.
1-3   Use the ▲/▼/◄/► buttons to enter the 
password. Move the cursor to the right side 
of the ENTER NEW PASSWORD box (small) 
and press the ► button to display the NEW 
PASSWORD AGAIN box, enter the same 
PASSWORD again.
1-4   Move the cursor to the right side of the 
NEW PASSWORD AGAIN box and press 
the ► button to display the NOTE NEW 
PASSWORD box for about 30 seconds, 
please make note of the password during 
this time. 
Pressing the ENTER button on the remote control or ► button on the 
projector will return to MyScreen PASSWORD on/off menu.
When a password is set for MyScreen:
• The MyScreen registration function (and menu) will be unavailable.
• The MyScreen Lock menu will be unavailable.
• The START UP setting will be locked on MyScreen (and the menu will be 
unavailable).
Turning the MyScreen PASSWORD off will allow normal operation of these 
functions.
• Please do not forget your MyScreen PASSWORD.
2 Turning off the MyScreen PASSWORD2-1   Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off 
menu.
2-2 
  Select OFF to display the ENTER 
PASSWORD box (large). Enter the registered 
password and the screen will return to the 
MyScreen PASSWORD on/off menu.
If an incorrect PASSWORD is input, the menu will 
close. If necessary, repeat the process from 2-1.
3 If you have forgotten your password3-1   Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off 
menu.
3-2   Select OFF to display the ENTER PASSWORD box (large). The 10 digit 
Inquiring Code will be displayed inside the box.
3-3   Contact your dealer with the 10 digit Inquiring Code. Your password will 
be sent after your user registration information is confirmed.
(continued on next page)
ENTER NEW PASSWORD 
box (small)
ENTER PASSWORD box  (large) 
						

							80
SECURITY menu
ItemDescription
PIN LOCK
PIN LOCK is a function which prevents the projector from being used unless 
a registered Code is input.
1 Turning on the PIN LOCK1-1   Use the ▲/▼ buttons on the SECURITY menu to 
select PIN LOCK and press the ► button or the 
ENTER button to display the PIN LOCK on/off 
menu.
1-2   Use the ▲/▼ buttons on the PIN LOCK on/
off menu to select ON and the Enter PIN 
Code box will be displayed. 
1-3   Input a 4 part PIN code using the ▲/▼/◄/►, 
COMPUTER or INPUT button. 
The PIN Code again box will appear. Reenter 
the same PIN code. This will complete the PIN 
code registration.
• If there is no key input for about 55 seconds  
while the Enter PIN Code box or the PIN Code again box is displayed, 
the menu will close. If necessary, repeat the process from 1-1.
Afterwards, anytime the projector is restarted after AC power  is turned off 
the Enter PIN Code box will be displayed. Enter the registered PIN code.
The projector can be used after entering the registered PIN code. If an 
incorrect PIN code is input, the Enter PIN code box will be displayed again.
If an incorrect PIN code is input 3 times, the projector will turn of f. Afterwards 
the projector will turn off every time an incorrect PIN code is input. The 
projector will also turn off if there is no key input for about 5 minutes while 
the Enter PIN code box is displayed.
This function will activate only when the projector is started after  AC power 
is turned off.
• Please do not forget your PIN code.
2 Turning off the PIN LOCK2-1   Follow the procedure in 1-1 to display the PIN LOCK on/off menu. 
2-2   Use the ▲/▼ buttons to select OFF and the Enter PIN Code box will be 
displayed. 
Enter the registered PIN code to turn the PIN LOCK function off.
If an incorrect PIN code is input 3 times, the projector will turn of f. 
3 If you have forgotten your PIN code3-1  While the Enter PIN code box is displayed, press and hold the  RESET 
button for three seconds or press and hold the  INPUT button for 3 
seconds while pressing the ► button on the projector. 
The 10 digit Inquiring Code will be displayed.
• If there is no key input for about 5 minutes 
while the Inquiring Code is displayed, the 
projector will turn off.
3-2   Contact your dealer with the 10 digit Inquiring Code. Your PIN code will 
be sent after your user registration information is confirmed.
(continued on next page)