Dukane Imagepro 8928 Projector Users Manual

21
1.Make sure that the power cord is firmly and 
correctly connected to the projector and the 
outlet.
Turning on the power
2.Make sure that the POWER indicator is 
steady orange (
115). Then remove the 
lens cover.
3.Press STANDBY/ON button on the 
projector or the remote control.
The projection lamp will light up and  POWER  
indicator will begin blinking in green. When the  
power is completely on, the indicator will stop blinking and light in steady 
green (
115).
Power on/off
To display the...

22
Power on/off
►A strong light is emitted when the projector’s power is on.  
Do not look into the lens of the projector or look inside of the projector through 
any of the projector’s openings.
►Do not touch around the lamp cover and the exhaust vents during use or just 
after use, since it is too hot. WARNING
1.Press the STANDBY/ON button on the projector or the remote control.  
The message “Power off?” will appear on the screen for about 5 seconds.
Turning off  the power
2.Press the STANDBY/ON...

23
Operating
1.
Adjusting the volume
Use the VOLUME +/VOLUME - buttons to adjust the volume.
A dialog will appear on the screen to aid you in adjusting the 
volume. If you do not do anything, the dialog will automatically 
disappear after a few seconds.
●  When 
 is selected for current picture input port, the volume 
adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu 
(
49).
●  Even if the projector is in the standby mode, the volume is adjustable when 
both of the following conditions...

24
1.Press INPUT button on the projector. 
Each time you press the button, the projector switches its 
input port from the current port as below.
Selecting an input signal
●  While ON is selected for AUTO SEARCH item in OPTION menu (56), the 
projector will keep checking the ports in above order repeatedly till an input 
signal is detected.
● It may take several seconds to project the images from the USB TYPE B port.
               COMPUTER IN1  COMPUTER IN2  LAN 
    VIDEO...

25
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
MY SOURCE / 
DOC. CAMERA button
1.Press the MY SOURCE / DOC. CAMERA button on 
the remote control. The input signal will be changed 
into the signal you set as MY SOURCE (
59).
●  This function also can use for document camera. Select the  input port that connected the document camera.
Operating
1.Press SEARCH  button on the remote control.
The...

26
Operating
Selecting an aspect ratio
● ASPECT button does not work when no proper signal is inputted.
● NORMAL mode keeps the original aspect ratio setting.
●  The display will be dark for a split second while switching the Aspect, but this is not a malfunction.
  For a computer signal
8755N/8928/8931W/8937:
NORMAL  
  
4:3  
  
16:9  
  
16:10
       
8928/8930 : 
NORMAL  
  
4:3  
  
16:9  
  
16:10  
  NATIVE
   For a video signal, s-video signal or component video signal...

27
Operating
Adjusting the projector’s elevator
When the place to put the projector is slightly uneven 
to the left or right, use the elevator feet to place the 
projector horizontally. 
Using the feet can also tilt the projector in order to 
project at a suitable angle to the screen, elevating the 
front side of the projector within 14 degrees.
This projector has 2 elevator feet and 2 elevator buttons. 
An elevator foot is adjustable while pushing the elevator 
button on the same side as it.
1. 
Holding...

28
Operating
1.Press POSITION button on the remote control when no menu is 
indicated.
The “POSITION” indication will appear on the screen.
Adjusting the position
2.Use the ▲/▼/◄/► cursor buttons to adjust the picture position.
When you want to reset the operation, press  RESET button on 
the remote control during the operation.
To complete this operation, press POSITION  button again. Even if 
you do not do anything, the dialog will automatically disappear 
after a few seconds.
●  
When this function is...

29
Operating
1.Press KEYSTONE button on the remote 
control. A dialog will appear on the screen 
to aid you in correcting the distortion.
Correcting the keystone distortions
2.Use the ▲/▼ cursor buttons to select AUTO or MANUAL 
operation, and press the ► button to perform the following.
(1)  AUTO executes automatic vertical keystone correction. 
(2)  MANUAL displays a dialog for keystone correction. Use the ◄/► buttons for adjustment.
To close the dialog and complete this operation, press 
KEYSTONE...

30
Operating
1.
Using the magnify feature
2.
MAGNIFY
ON/OFF button
VIDEODOC.CAMERA
KEYSTONE
ASPECT
SEARCHBLANK
MUTE
MY BUTTON
POSITION ESC MENU
RESET
COMPUTER MY SOURCE/
AUTOMAGNIFYPAGE
DOWN
ON
OFF
FREEZEUP
ー
＋VOLUME
1 2
ENTER
3.
4.
Press the MAGNIFY ON button on the remote control. 
The picture will be magnifi ed, and the MAGNIFY dialog 
will appear on the screen. When the 
MAGNIFY 
ON button is pressed for the fi rst time after the 
projector is turned on, the picture will be zoomed 
by 1.5 times. On...