Dukane Imagepro 8916 Projector Users Manual

							


ENGLISH
Projector 
8755H/8916 
User's Manual (concise)
Thank you for purchasing this projector.
WARNING  ►Before using this product, be sure to read all manuals for this 
product. See “Using the CD manual”  (
 15) to read the manuals in the CD. 
After reading them, store them in a safe place for future reference.

Contents of package...........................
Preparations   .......................................2
  Fastening the lens cover   .................................2
  Loading batteries into the remote control   ........2
Arrangement  .......................................3
Connecting your devices   ....................4
Connecting power supply   ...................5
Turning on the power  ..........................5
Adjusting the projector’s elevator   .......6

Displaying the picture  .........................7
Turning off the power  ..........................8
Replacing the lamp  .............................9
Cleaning and replacing the air filter   ..
Using the CD manual  .......................  2
Regulatory notices  ............................  3
Specifications  ...................................  5
Warranty and after-service  ...............  6
Contents
Contents of  package
Your projector should come with the items 
shown below. Check that all the items are 
included. Contact to your dealer immediately 
if any items are missing.
(1) Remote control with two AA batteries 
(2) Power cord 
(3) RGB cable
(4) Audio/Video cable
(5) 
 Lens cover and Strap 
 
Lens cover is attached to the projector.
(6)  User’s manuals (Book x1, CD x1)
(7) Soft case
(8) Security label
NOTE  • Keep the original packing materials for future reshipment. Be sure 
to use the original packing materials when moving the projector. Use special 
caution for the lens.
( )
(2)
(3)
(4)
(6)
(7)
(8)
(5)VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTEMY BUTTONPOSITION1 2
ESCENTERMENURESET
COMPUTERMY SOURCE/AUTOMAGNIFYPAGE      UPVOLUMEDOWNoONOFF9×FREEZE 
						

							
2

Fastening the lens cover
To avoid losing the lens cover, please fasten the lens cover 
to the projector using the enclosed strap.
. Fix the strap to the strap hole of the lens cover. 
Thread one end of the strap through the strap hole of 
the lens cover and make the loop at the end, and let the 
other end of the strap through the loop. Not have a knot 
in the strap at either end.
2. Fix the strap to the strap hole of the projector. Thread 
the other end of the strap through the strap hole of the projector and make 
the loop there. Let the lens cover with the one end of strap through the loop.
Preparations
Loading batteries into the remote control
Please set the batteries to the remote control before using it. If the remote control 
starts to malfunction, try to replace the batteries. If you will not use the remote 
control for long period, remove the batteries from the remote control and store 
them in a safe place.
. Holding the hook part of the battery 
cover, remove it.
2. Align and insert the two AA batteries 
(HITACHI MAXELL, Part No.LR6 or R6P) 
according to their plus and minus terminals 
as indicated in the remote control.
3. Replace the battery cover in the direction 
of the arrow and snap it back into place.
WARNING  ►Always handle the batteries with care and use them only as 
directed. Improper use may result in battery explosion, cracking or leakage, 
which could result in fire, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specified. Do not use batteries of dif ferent 
types at the same time. Do not mix a new battery with used one. 
• Make sure the plus and minus terminals are correctly aligned when loading a battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery.
• Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry place.
• If you observe battery leakage, wipe out the leakage and then replace a battery.  
If the leakage adheres to your body or clothes, rinse well with water  immediately.
• Obey the local laws on disposing the battery. 
						

							
3
ENGLISH

On a horizontal surface
Suspended from the ceiling
• Keep a space of 30 cm or more between 
the sides of the projector and other objects 
such as walls.
• Consult with your dealer before a special 
installation such as suspending from a ceiling.
WARNING  ►Install the projector in a stable horizontal position.
►Place the projector in a cool place, and ensure that there is sufficient ventilation.
►Do not place the projector anyplace where it may get wet.
CAUTION  ►Avoid placing the projector in smoky, humid or dusty place.
►Position the projector to prevent light from directly hitting the projector’s 
remote sensor.
Arrangement
Refer to the illustrations and tables below to determine screen size and projection distance.
The values shown in the table are calculated for a full size screen: 1024×768
  a  Screen size (diagonal)
  b  Projection distance (±10%)
 c1 , c2  Screen height (±10%)
   Screen size(diagonal)
4 : 3 screen16 : 9 screen
  Projection distance Screen heightScreen height Projection distance Screen height Screen height min.max.min.max.inchmminchminchcminchcminchminchminchcminchcminch
300.80.934 .  4  4   652 .038 . 4539 5-10
40 .0  .246 .456552262 .350 .56  5 20-2-1
50 .3  .558 .870692783 .663 .9766425-2-1
60 .5  .8702. 84823294 .9762.39 7730-2-1
70 .82.  8 2.598963842.3892.7 079035-3-1
802.02.4932.8 2  043 252.6 023.   22  034 -3-1
902.32.7 053.2 26  2349 452.9 53.5 38  646-4-1

00
2.53.0  73.6 40  3754 563.2 273.9 53  295 -4-2

20
3.03.6  404.3 69  6565 873.9 534.7 84  546 -5-2

50
3.84.5  765.42 2068 2394.9 925.8230 9376-6-2
2005. 6.02357.2282274 0830 26.52567.8307257 0 -8-3
2506.47.52949.0353343 3538 58. 3209.8384322 27-10-4
3007.69.0352 0.84234   6246 89.8384 .746 386 52-12-5
babc1c1c2c2 
						

							
4

Connecting your devices
Be sure to read the manuals for devices before connecting them to the projector. 
Make sure that all the devices are suitable to be connected with this product, and 
prepare the cables required to connect. Please refer to the following illustrations 
to connect them.
WARNING  ►Do not disassemble or modify the projector and accessories.
►Be careful not to damage the cables, and do not use damaged cables.
CAUTION  ►Turn off all devices and unplug their power cords prior to 
connecting them to projector. Connecting a live device to the projector may 
generate extremely loud noises or other abnormalities that may result in 
malfunction or damage to the device and the projector.
►Use appropriate accessory or designated cables. Ask your dealer about non-
accessory cables which may be required a specific length or a ferrite core by 
the regulations. For cables with a core only at one end, connect the end with 
the core to the projector.
►Make sure that devices are connected to the correct ports. An incorrect 
connection may result in malfunction or damage to the device and the projector.
AUDIO OUTRGB OUTAUDIO OUTUSBRGB OUTRS-232C
RGB IN
      Y      CB/PB     CR/PRCOMPONENT VIDEO OUT L  R AUDO IN OUTVIDEO OUT L  R AUDO IN OUT L  R AUDO IN OUTS-VIDEO OUT
AUDIO IN
VCR/DVD player
Speakers(with an amplifier)
PC
Monitor 
						

							
5
ENGLISH

Connecting power supply
. Put the connector of the power cord into the 
AC inlet of the projector.
2. Firmly plug the power cord’s plug into the 
outlet. 
WARNING  ►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, contact 
to your dealer to newly get correct one.
• Only plug the power cord into an outlet whose voltage is matched to the power 
cord. The power outlet should be close to the projector and easily accessible. 
Remove the power cord for complete separation.
• Never modify the power cord. 
Turning on the power
. Make sure that the power cord is firmly and 
correctly connected to the projector and the 
outlet.
2. Remove the lens cover, and set the power 
switch to the ON position (marked “׀”).
3. Press the STANDBY/ON button on the 
projector or the remote control.
The projection lamp will light up and the POWER 
indicator will begin blinking in green. When the 
power is completely on, the indicator will stop 
blinking and light in steady green.
WARNING  ►A strong light is emitted when the projector’s power is on. Do not look into 
the lens of the projector or look inside of the projector through any of  the projector’s openings.
NOTE  • Please power on the projector prior to the connected devices.
• When the AUTO ON of the OPTION menu is set to the TURN ON, and the 
power was turned off by the power switch last time, turning the power switch on 
makes the projection lamp light on without pushing the STANDBY/ON button. 
For more information, please see the “Operating Guide” in the CD.
AC inletPower cord
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTEMY BUTTONPOSITION1 2
ESCENTERMENU
RESET
COMPUTERMY SOURCE/AUTOMAGNIFYPAGE      UPVOLUMEDOWNoONOFF9×FREEZE
STANDBY/ON buttonPOWER indicator
Power switch 
						

							
6

Adjusting the projector's elevator
When the place to put the projector is slightly uneven to 
the left or right, use the elevator feet to place the projector 
horizontally. 
Using the feet can also tilt the projector in order to project at a suitable angle to 
the screen, elevating the front side of the projector within 10 degrees.
This projector has 2 elevator feet and 2 elevator buttons. An elevator foot is 
adjustable while pushing the elevator button on the same side as it.
. Holding the projector, push the elevator buttons to loose the elevator feet.
2. Position the front side of the projector to the desired height.
3. Release the elevator buttons in order to lock the elevator feet.
4. After making sure that the elevator feet are locked, put the projector gently .
5. If necessary, the elevator feet can be manually twisted to make more precise 
adjustments. Hold the projector when twisting the feet.
To loose an elevator foot, push the 
elevator button on the same side as it.
CAUTION  ►Do not handle the elevator buttons without holding the 
projector, since the projector may drop down.
►Do not tilt the projector other than elevating its front within 10 degrees using 
the adjuster feet. A tilt of the projector exceeding the restriction could cause 
malfunction or shortening the lifetime of consumables, or the projector itself.
To finely adjust, twist the foot.
10° 
						

							
7
ENGLISH

Displaying the picture
. Activate your signal source. Turn the signal 
source on, and make it send the signal to 
the projector.
2. Use the VOLUME +/VOLUME - buttons to 
adjust the volume.  
To have the projector silent, press the MUTE 
button on the remote control.
3. Press the INPUT button on the projector.  
Each time you press the button, the 
projector switches its input port in turn.
You can also use the remote control to 
select an input signal. Press the VIDEO 
button for selecting an input signal from the 
COMPONENT (Y, Cb/Pb, Cr/Pr), VIDEO 
or S-VIDEO port, or the COMPUTER 
button for selecting an input signal from the 
COMPUTER IN1 or COMPUTER IN2.
4. Press the ASPECT button on the remote 
control. Each time you press the button, 
the projector switches the mode for aspect 
ratio in turn.
5. Use the zoom ring to adjust the screen 
size.
6. Use the focus ring to focus the picture.
INPUT button
VOLUME button
MUTE button
▲ cursor button
▼ cursor button
VIDEO button
COMPUTER button
ASPECT button
NOTE  • The ASPECT button does not work when no proper signal is inputted.
 • For the details of how to adjust the picture, please see the “Operating Guide” 
in the CD.
Focus ring
Zoom ring
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTEMY BUTTON
POSITION
1 2
ESCENTER
MENU
RESET
COMPUTERMY SOURCE/AUTOMAGNIFYPAGE      UPVOLUME
DOWNoONOFF9×FREEZE
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTEMY BUTTON
POSITION
1 2
ESCENTER
MENU
RESET
COMPUTERMY SOURCE/AUTOMAGNIFYPAGE      UPVOLUME
DOWNoONOFF9×FREEZE 
						

							
8

VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTEMY BUTTONPOSITION1 2
ESCENTERMENU
RESET
COMPUTERMY SOURCE/AUTOMAGNIFYPAGE      UPVOLUMEDOWNoONOFF9×FREEZE

Turning off  the power
. Press the STANDBY/ON button on the projector 
or the remote control.
The message "Power off?" will appear on the 
screen for about 5 seconds.
2. Press the STANDBY/ON button again while the 
message appears. 
The projector lamp will go off, and the POWER 
indicator will begin blinking in orange. Then the 
POWER indicator will stop blinking and light in 
steady orange when the lamp cooling is complete.
3. Make sure that the POWER indicator lights in 
steady orange, and set the power switch to the 
OFF position (marked “O”). Attach the lens cover.
Do not turn the projector on for about 10 minutes 
or more after turning it off. Turning the projector on 
again too soon could shorten the lifetime of some 
consumable parts of the projector.
WARNING  ►Do not touch around the lamp cover and the exhaust vents 
during use or just after use, since it is too hot.
►Remove the power cord for complete separation. The power outlet should be 
close to the projector and easily accessible.
NOTE  • Please power off the projector after any connected devices are powered off.
 • This projector has the AUTO OFF function that can make the projector turn off 
automatically. For more information, please see the “Operating Guide” in the CD.
STANDBY/ON buttonPOWER indicator
Power switch 
						

							
9
ENGLISH

Replacing the lamp
A lamp has finite product life. Using the lamp for long periods of time could cause 
the pictures darker or the color tone poor. Note that each lamp has a different 
lifetime, and some may burst or burn out soon after you start using them. 
Preparation of a new lamp and early replacement are recommended. To prepare 
a new lamp, contact to your dealer and tell the lamp type number.
Type number : 456-8755H
. Turn the projector off, and unplug the power cord. 
Allow the projector to cool for at least 45 minutes.
2. Prepare a new lamp. If the projector is mounted 
on a ceiling, or if the lamp has broken, also ask 
the dealer to replace the lamp.
In case of replacement by yourself, follow the following 
procedure.
3. Loosen the screw (marked by arrow) of the lamp 
cover and then slide the lamp cover to the side to 
remove it.
4. Loosen the 2 screws (marked by arrow) of the 
lamp, and slowly pick up the lamp by the handles. 
5. Insert the new lamp, and retighten firmly the 
2 screws of the lamp that are loosened in the 
previous process to lock it in place. 
6. Slide the lamp cover back in place and firmly 
fasten the screw of the lamp cover.
7. Turn the projector on and reset the lamp time 
using the LAMP TIME item in the OPTION menu. 
(1) Press the MENU button to display a menu. 
(2) Point at the Go to Advanced Menu … in the menu 
using the ▼/▲ button, then press the ► button.
(3) Point at the OPTION in the left column of the menu 
using the ▼/▲button, then press the ► button.
(4) Point at the LAMP TIME using the ▼/▲ button, then 
press the ► button. A dialog will appear.
(5) Press the ▲ button to select RESET on the dialog. It performs resetting the 
lamp time.
NOTE  • Please reset the lamp time only when you have replaced the lamp, 
for a suitable indication about the lamp.
CAUTION  ►Do not touch any inner space of the projector, while the lamp 
is taken out.
Lamp cover
Handles 
						

							
0

 HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE
WARNING  ►The projector uses a high-pressure mercury glass lamp. The 
lamp can break with a loud bang, or burn out, if jolted or scratched, handled 
while hot, or worn over time. Note that each lamp has a different lifetime, and 
some may burst or burn out soon after you start using them. In addition, when 
the bulb bursts, it is possible for shards of glass to fly into the lamp housing, 
and for gas containing mercury to escape from the projector’s vent holes.
►About disposal of a lamp: This product contains a mercury lamp; do not put 
it in a trash. Dispose of it in accordance with environmental laws. 
• 
 For lamp recycling, go to 
www.lamprecycle.org (in the US).
• 
 
For product disposal, contact your local government agency 
 
or www.eiae.org (in the US) or www.epsc.ca (in Canada).
For more information, contact to your dealer.
•  If  the  lamp  should  break  (it  will  make  a  loud  bang  when  it  does), 
unplug  the  power  cord  from  the  outlet,  and  make  sure  to  request  a 
replacement  lamp  from  your  local  dealer.  Note  that  shards  of  glass 
could damage the projector’s internals, or cause injury during handling, 
so please do not try to clean the projector or replace the lamp yourself.
•  If  the  lamp  should  break  (it  will  make  a  loud  bang  when  it  does), 
ventilate  the  room  well,  and  make  sure  not  to  breathe  the  gas  that 
comes out of the projector vents, or get it in your eyes or mouth.
• Before replacing the lamp, turn the projector off and unplug the power 
cord,  then  wait  at  least  45  minutes  for  the  lamp  to  cool  sufficiently. 
Handling the lamp while hot can cause burns, as well as damaging the lamp.
• Never unscrew except the appointed (marked by an arrow) screws.
•  Do  not  open  the  lamp  cover  while  the  projector  is  suspended  from 
a  ceiling.  This  is  dangerous,  since  if  the  lamp’s  bulb  has  broken,  the 
shards  will  fall  out  when  the  cover  is  opened.  In  addition,  working  in 
high  places  is  dangerous,  so  ask  your  local  dealer  to  have  the  lamp 
replaced even if the bulb is not broken.
•  Do  not  use  the  projector  with  the  lamp  cover  removed. At  the  lamp 
replacing,  make  sure  that  the  screws  are  screwed  in  firmly.  Loose 
screws could result in damage or injury.
• Use only the lamp of the specified type.
•  If  the  lamp  breaks  soon  after  the  first  time  it  is  used,  it  is  possible 
that  there  are  electrical  problems  elsewhere  besides  the  lamp.  If  this 
happens, contact to your local dealer or a service representative.
• Handle with care: jolting or scratching could cause the lamp bulb to bur st during use.
• Using the lamp for long periods of time, could cause it dark, not to light 
up  or  to  burst.  When  the  pictures  appear  dark,  or  when  the  color  tone 
is  poor,  please  replace  the  lamp  as  soon  as  possible.  Do  not  use  old 
(used) lamps; this is a cause of breakage. 
Disconnect the plug from the power outlet