Dukane Imagepro 8913h Projector Users Manual

							

ENGLISH

Please check and clean the air filter periodically. When the indicators or a message 
prompts you to clean the air filter, comply with it as soon as possible. The air filter has two 
kinds of filters inside. Replace the filters when they are damaged or too soiled. To prepare 
the new filters, contact to your dealer and tell the following type number.
Type number : MU05611
When you replace the lamp, please replace the air filter. 
An air filter of specified type will come together with a 
replacement lamp for this projector.
. Turn the projector off, and unplug the power cord. Allow 
the projector to sufficiently cool down.
2. Use a vacuum cleaner on and around the filter cover. 
3. Pull the filter cover knobs while lifting it, to take the filter 
unit off.
4. Use a vacuum cleaner for the filter vent of the projector 
and both sides of the filter unit.
If the filters are damaged or too soiled, replace them according 
to the following procedure number 5 to 7. Otherwise, please 
jump to the procedure number 8.
5. Pull the filter frame’s knob up while holding the filter 
cover to remove the filter frame, then take the filters out.
6. Set new filters where former filters were. Put the larger 
meshed filter into a filter cover first. Then put the finer 
meshed filter on the larger meshed one.
7. Put the filter frame back where it was.
8. Put the filter unit back into the projector.
9. Turn the projector on and reset the filter time using the  
FILTER TIME item in the EASY MENU. 
(1) Press the MENU button to display a menu. 
(2) Point at the FILTER TIME using the ▼/▲ button, then press the ► button. A dialog will appear.
(3) Press the ▲ button to select RESET on the dialog. It performs resetting the filter time.
Cleaning and replacing the air filter
WARNING  ►Before taking care of the air filter, make sure the power cable 
is not plugged in, then allow the projector to cool sufficiently.
►Use only the air filter of the specified type. Do not use the projector without the 
air filter or the filter cover. It could result in a fire or malfunction to the projector.
►Clean the air filter periodically. If the air filter becomes clogged by dust or the like, 
internal temperatures rise and could cause a fire, a burn or malfu nction to the projector.
NOTE  • Please reset the filter time only when you have cleaned or replaced 
the air filter, for a suitable indication about the air filter.
• The projector may display the message such as “CHECK THE AIR FLOW” or 
turn off the projector, to prevent the internal heat level rising. 
Filter cover
Filter cover knobs
Filter unit
 Filter cover
Filter frame
Filter (finer meshed)
Filter (larger meshed) 
						

							
2

Using the CD manual
The other manuals for this product are written into the included CD-ROM titled 
“User’s Manual (detailed)”. Before using the CD-ROM, please read the following 
to ensure the proper use. 
 System requirements
The system for using the CD-ROM requires the following. 
  Windows®:
   OS:Microsoft® Windows® 98, 98SE, NT4.0, Me, 2000/XP, or 
later
 
CPU:Pentium® processor 133MHz / Memory:32MB or more
  Macintosh®:
 
OS:Mac OS 10.2 or later
 
CPU:Power PC® / Memory:32MB or more
  CD-ROM drive:
 
4x CD-ROM drive
  Display: 
 
256 color / 640x480 dots resolution
  Applications:
 
 
Microsoft Internet Explorer4.0 and
 
Adobe Acrobat Reader 4.0 or later
 How to use the CD
1. Insert CD into PC’s CD-ROM drive.
  Windows®:  
 In a while, Web browser automatically starts. Start up 
window comes up.
  Macintosh®:
 
 (1) Double-click on the ”Projectors” icon appeared on the 
desktop screen.  
(2) When “main.html” file is clicked, Web browser will start 
and Initial window will appear.
2. 
 
Click the model name of your projector first, and then click language you want 
from the displayed list. The User’s manual (detailed) will open.
CAUTION  ►Only use the CD-ROM in a computer CD drive. The CD-
ROM is designed for PC use only. NEVER INSERT THE CD-ROM INTO A 
NON-COMPUTER CD PLAYER! Inserting the CD-ROM into an incompatible 
CD drive may produce a loud noise, which in turn MAY RESULT IN EAR AND 
SPEAKER DAMAGE! 
• After using CD-ROM, please put it into CD case and keep it. Please keep 
the CD neither in direct sunlight nor in a high temperature and high humidity 
environment.
NOTE  • The information in the CD-ROM is subject to change without notice.
• No responsibility is taken for any obstacle and defect to hardware and 
software of your PC as a result of the use of the CD-ROM.
• All or Any part of the information in the CD-ROM must not be copied, 
reproduced or republished without notice to our company. 
						

							
3
ENGLISH

Regulator y notices
Declaration of Conformity
Trade name   HITACHI
Model Number   CP-X201/CP-X301/CP-X401/CP-X450
Responsible Party
  Hitachi America, Ltd.
Address
  900 Hitachi way, Chula Vista, CA 91914-3556  U.S.A.
Telephone Number
  +1 -800-225-1741
This device complies with part 15 of the FCC Rules. Operation is subject to the following 
two conditions: (1) This device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired 
operation.
FCC Statement warning
WARNING: This equipment has been tested and found to comply with the limits fo r a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televisio n reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-  Reorient or relocate the receiving antenna.
-   Increase the separation between the equipment and receiver.
- 
 Connect the equipment into an outlet on a circuit different from that to which the receiver 
is connected.
- 
 
Consult the dealer or an experienced radio/TV technician for help.
INSTRUCTIONS TO USERS: This equipment complies with the requirements of FCC (Federal Communication Commission) equipment provided that the following conditions are met. Some cables have to be used with the core set. Use the accessory cable or a designated-type cable for the connection. For cables that have a core only at one end, connect the core to the projector.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
For the Customers in CANADA
NOTICE: This Class B digital apparatus complies with Canadian ICES-003.
(continued on next page) 
						

							
4

Information for users applicable in European Union countries
1. The manufacturer (Gemtek) hereby declare that this equipment (wireless network card), model SD-Link11g is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
2. This symbol on the product or on its packaging means that your electrical and electronic equipment should be disposed at the end of life separately from your household wastes. There are separate collection systems for recycling in EU. For more information, please contact the local authority or the dealer where you purchased the product.
Regulatory notices (continued)
0560! 
						

							
5

ENGLISH
Specifications
ItemSpecifications
Product nameLiquid crystal projector
Liquid Crystal Panel
Panel size1.6 cm (0.63 type)
Drive systemTFT active matrix
Pixels786,432 pixels (1024 horizontal x 768 vertical)
Lens
Zoom lens   8755H, 8912H           : F=2.3~2.5  f=18.9~22.6 
8913H                        : F=1.6~1.8  f=18.9~22.68916                          : F=1.6~1.8  f=18.9~22.6         (approximately)
Lamp 8912H, 8755H :          220W UHB
8913H, 8916          
                         230W UHB
Audio output7 W
Power supplyAC 100-120V/3.5A, AC220-240V/1.5A
Power consumption320W
Temperature range5 ~ 35°C (Operating)
Size340 (W) x 100 (H) x 270 (D) mm   *Excluding protrusionsPlease refer to the following figure.
Weight (mass)approx. 3.5 kg
Ports
Computer input portCOMPUTER IN1  
 
....................D-sub 15 pin mini x1COMPUTER IN2  
 
....................D-sub 15 pin mini x1Computer output portMONITOR OUT  
 
....................D-sub 15 pin mini x1Video input portCOMPONENT (Y, Cb/Pb, Cr/Pr)  
 
........................................RCA x3S-VIDEO   ..........mini DIN 4 pin x1VIDEO  .............................RCA x1
Audio input/output portAUDIO IN1   ...........Stereo mini x1AUDIO IN2  ...........Stereo mini x1AUDIO IN3  ......................RCA x2AUDIO OUT   .........Stereo mini x1OthersUSB  ..............................USB-B x1CONTROL   ............D-sub 9 pin x1
Optional parts
Lamp : 456-8755HAir filter : MU05611
 *For more information, contact to your dealer.
340
100112
270
[unit : mm] 
						

							
6

Warranty and after-ser vice
If an abnormal operation (such as smoke, strange odor or excessi ve sound) should occur, stop using the projector immediately. Otherwise if a problem occurs with the projector, first refer to the “Troubleshooting” of the “Operating Guide” in the CD and run through the suggested checks. If this does not resolve the problem, please contact to your dealer  or service company. They will tell you what warranty condition is applied.
Please check the following web address where you may find the latest information for this projector.
http://www.dukcorp/av
Trademark acknowledgment
• Mac, Macintosh, Power PC and Mac OS are registered trademarks of Apple Computer, Inc.• Pentium is a registered trademark of Intel Corporation.• Adobe and Acrobat are registered trademarks of Adobe Systems Incorporated.• Windows is a registered trademark of Microsoft Corporation.• VESA and SVGA are trademarks of the Video Electronics Standard Association.All other trademarks are the properties of their respective owners.
NOTE  • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in 
this manual.
• The reproduction, transfer or copy of all or any part of this document is not 
permitted without express written consent.