Dukane Imagepro 8911 Portable Lcd Projector Users Manual

							
9

Setting up
About the fi lter cover for bottom-up use
WARNING  ►Do not replace the fi lter cover during use or immediately 
after use. While the projector connects with a power supply, or the projector is 
in a high temperature state, handling could cause an electric shock, a fi re, a 
burn and/or malfunction to the projector.Before handling, make sure the power 
switch is off and the power cord is not plugged in, then wait at least 45 minutes.
When the projector is installed bottom up, please use the accessory fi lter cover 
for bottom-up use. It is higher than usual fi lter cover, to keep the space for intake 
ventilation. Please change in the following procedure.
1. After making sure that the projector is cool adequately, slowly turn the 
projector so that the lens-side is facing up. Please be careful for a projector 
not to fall. While the projector is placed lens-side up, hold the projector .
2.Unhooking the fi lter cover’s claws, pull the fi lter cover in the direction of the 
arrow to remove it.
3. Replace the fi lter cover for bottom-up use and snap it back into place.
4. Slowly turn the projector so that the top is facing up.
Filter cover’s claws
To set
Filter cover’s claws
Filter cover 
To remove
Filter cover for bottom-up use 
						

							10
Setting up
Connecting your devices
CAUTION  ►Turn off all devicesy
prior to cony
Qecting them t\
o the projecty
Rr. 
Attempting toy
connect a liy
Ye device to y
Whe projector \
may generate \
extremely 
loud noises or other abnormalities that may result in malfunction and/or damage 
to the devicey
and/or projey
Ftor.
►Use the accey
Vsory cable oy
U a designated\
-type cable y
Ior the connec\
tion. 
Some cables hy
Dve to be usey
G with core sy
Ht. A too long cay
Ele may causey
a 
certain pictuy
Ue degradationy
 Please consy
Xlt with youry
dealer for dy
Htails. For 
cables that hy
Dve a core ony
Oy at one endy
 connect they
core to the \
projector.
►Make sure thy
Dt you connecy
W devices to y
Whe correct po\
rt. Incorrecty
connection 
may result in\
 malfunction y
Dnd/or damage \
to the devicey
and/or projey
Ftor. 
NOTE  • Whenever attey
Ppting to conn\
ect a laptop \
computer to ty
Ke projector, be sure 
to activate ty
Ke laptop’s RGB externay
O image output\
 (set the la\
ptop to CRT display or y
Wo 
simultaneous y
/CD and CRT displayyf)\
RUGHWDLOVRQ\
KRZWKLVLV\
GRQHSOHDVH\
UHIHU to the 
instruction my
Dnual of the y
Forresponding y
Oaptop computey
U.
• Secure the scy
Uews on the cy
Rnnectors and \
tighten.
• Some computery
V may have muy
Otiple displayy
screen modes.\
 Use of somey
of these 
modes will noy
W be possible \
with this proy
Mector.
• For some y
5GB signal mod\
es, the optiy
Rnal Mac adapt\
er is necessay
Uy.
• When the i\
mage resolutiy
Rn is changed \
on a computer, depending y
Rn an input, \
automatic adjy
Xst function m\
ay take some \
time and may \
not be compley
Wed. In this \
case, 
you may not y
Ee able to sey
H a check boxy
to select “y

						

							
11

Y
VIDEO
RGB IN1RGB IN2
DVI-D
RGB OUT CONTROLAUDIO-IN
REMOTE
 
CONTROL
US
B
DC OUT
S-VIDEO
LAN
COMPONENT VIDE
O
CB/PBCR/PR
R-AUDIO IN-L AUDIO-OU
T
Y
VIDEO
RGB IN1
RGB IN2
DVI-D
RGB OUT CONTROLAUDIO-IN
REMOTE
 
CONTROL
US
B
DC OUT
S-VIDEO
LAN
COMPONENT VIDE
O
CB/PBCR/PR
R-AUDIO IN-L AUDIO-OU
T
Y
VIDEO
RGB IN1
RGB IN2
DVI-D
RGB OUT CONTROL
AUDIO-IN
REMOTE
 
CONTROL
USBDC OUT
S-VIDE
O
LAN
COMPONENT VIDEO
CB/PBCR/PR
R-AUDIO IN-L AUDIO-OU
T
Y
VIDEO
RGB IN
1 RGB IN2
DVI-D
RGB OU T CONTROLAUDIO-IN
REMOTE
 
CONTROL
US
B
DC OUT
S-VIDEOLANCOMPONENT VIDE
O
CB/PBCR/PR
R-AUDIO IN-L AUDIO-OU
T
RGB IN2
RGB OUT

Setting up
Examples of connection with a computer 
Audio outUSB(A)RS-232CDVI out
DVI cable
Stereo mini audio cable 
* AUDIO IN  is linked to  RGB IN1/2 
and DVI-D.
RGB outAudio out
Stereo mini audio cable 
RGB cable
RGB in
RGB cable
Audio inAudio in
Stereo mini audio cable 
USB cable
RS-232C cable
Connecting to a monitor (output)
Connecting to a speaker with amplifi er (output) 
						

							
12

Y
VIDEO
RGB IN1RGB IN2
DVI-D
RGB OUT CONTROL
AUDIO-IN
REMOTE
 
CONTROL
US
B
DC OUT
S-VIDE
O
LAN
COMPONENT VIDE
O
CB/PBCR/PR
R-AUDIO IN-L AUDIO-OU
T
Y
VIDEO
RGB IN1
RGB IN2
DVI-D
RGB OUT CONTROL
AUDIO-IN
REMOTE
 
CONTROL
US
B
DC OUT
S-VIDE
O
LAN
COMPONENT VIDE
O
CB/PBCR/PR
R-AUDIO IN-L AUDIO-OU
T
Y
VIDEO
RGB IN1
RGB IN2
DVI-D
RGB OUT CONTRO
L
AUDIO-IN
REMOTE
 
CONTROL
US
B
DC OUT
S-VIDE
O
LAN
COMPONENT VIDE
O
CB/PBCR/PR
R-AUDIO IN-L AUDIO-OU
T
Y
VIDEO
RGB IN1
RGB IN2
DVI-D
RGB OUT CONTRO
L
AUDIO-IN
REMOTE
 
CONTROL
US
B
DC OUT
S-VIDE
O
LAN
COMPONENT VIDE
O
CB/PBCR/PR
R-AUDIO IN-L AUDIO-OU
T

Setting up
Examples of connection with a VCR/DVD player
Audio (L) out
Video out
Audio cable 
Audio/Video cable Audio/Video cable 
Audio (L) outAudio (L) out
S-Video out
S-Video cable 
RGB out
Audio (L) out  
Component video out
RGB cable Component video out
Component video cable 
Y
CB/PB
CR/PR
Audio cable 
Audio (R) out
Audio (R) out
LAN cable (CAT-5)LAN cable (CAT-5)
LAN port
Y
CB/PB
CR/PR
Audio (R) out  
Component video cable  
						

							
13

Setting up
Connecting power supply
WARNING  ►Please use extra caution when connecting the power cord as 
incorrect or faulty connections may result in fi re and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, contact 
your dealer to newly get correct one.
• Only plug the power cord into an outlet rated for use with the power cord's 
specifi ed voltage range.
• Never modify the power cord. Never attempt to defeat the ground connection 
of the three-pronged plug.
1. Connect the connector of the power cord to the AC inlet of the projector.
2. Firmly plug the power cord's plug into the outlet. 
AC inlet
Connectorof the power cord 
						

							
14

Putting batteries

WARNING
  
►
Always handle the batteries with care and use them only as 

directed. Improper use may result in battery explosion, cracking or leakage, 

which could result in fi re, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries specifi ed. Do not use batteries of different 

types at the same time. Do not mix a new battery with used one. 

• 
Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

• 
Do not allow a battery in a fi re or water. Keep batteries in a dark, cool and dry place.

• 
If you observe a leakage of a battery, wipe out the fl ower and then replace a battery. 

If the fl ower adheres your body or clothes, rinse well with water immediately.

1. 
Remove the battery cover. 

Slide back and remove the battery cover in the direction of the arrow .

2. 
I
nsert the batteries.

 Align and insert the two AA batteries according to their plus and minus   

terminals as indicated in the remote control.

3. 
Close the battery cover.

Replace the battery cover in the direction of the arrow and snap it back into place.

Remote control
Laser pointer
This remote control has a laser pointer in place of a fi nger or rod. The laser beam works 
and theLASER INDICATOR lights while the LASER button is pressed.
WARNING  ►The laser pointer of the remote control is used in place of a 
fi nger or rod. Never look directly into the laser beam outlet or point the laser 
beam at other people. The laser beam can cause vision problems.
CAUTION  ►Use of controls or adjustments or performance of procedures 
other than those specifi ed herein may result in hazardous radiation exposure.
Remote control
STANDBY/ONVIDEOUPDOWN
BLANK
ASPECTPUSH
LASERINDICATOR
LASER
RGB
ENTER
ONOFF
ESCPOSITIONMAGN
IFYMUTEKEYST ONEFREEZEONE TOUCHAUTO PA
GE
MENURESETVOL
UME 
						

							
15

Remote control
Using the remote control
CAUTION  ►Be careful in handling the remote control.
• Do not drop or otherwise expose the remote control to physical impact.
• Do not get the remote control wet or place it on wet objects. Doing so may 
result in malfunction.
• Remove the batteries from the remote control and store them in a safe place if 
you won’t be using the remote control for an extended period. 
• Replace the batteries whenever the remote control starts to malfunction. 
• When strong lights, such as direct sunlight or light from an extremely close 
range (such as from an inverter fl uorescent lamp), hit the projector’s remote 
sensor, the remote control may cause to function. Adjust the direction of the 
projector to keep light from directly hitting the projector’s remote sensor.
The remote control works with the projector’s remote sensor.
• The range of the remote sensor is 3 meters with a 60- degree range (30 degrees 
to the left and right of the remote sensor).
• Also a remote signal refl ected in the screen etc. may be available. If it is diffi cult 
to send a remote signal to the sensor directly, please try.
•  Since  the  remote  control  uses  infrared  light  to  send  signals  to  the  projector 
(Class1  LED),  be  sure  to  use  the  remote  control  in  an  area  free  from  obstacles 
that could block the remote control’s output signal to the projector.
•  You  can  use  the  remote  control  as  a  wired  remote  control,  by  connecting  the 
REMOTE CONTROLports of the main unit and remote control via an audio cable 
(3.5 dia. stereo mini cable with plugs).
30º30ºapprox. 3 meters 
						

							
16

STANDBY/ONVIDEOUPDOWNBLANK
ASPECTPUSH
LASERINDICATOR
LASER
RGB
ENTER
ONOFF
ESCPOSITIONMAGNIFYMUTEKEYSTONEFREEZEONE TOUCH
AUTO PA
GE
MENURESETVOLUME

ST
ANDBY/ON
INPU
T KEYS TONE
RESE
TMENU
POWER T E M P L A M P

Power on/off
Power on/off
WARNING  ►When the power is on, a strong light is emitted. Do not look 
into the lens or vents of the projector.
NOTE  • Turn the power on/off in right order. Please power on the projector 
before the connected devices. Power off the projector after the connected devices.
Power switch
STANDBY/ON button
POWER indicator
Turning on the power
1. Make sure that the power cord is fi rmly and correctly 
connected to the projector and outlet.  
2. Remove the lens cap, and set the power switch to the 
ON position. 
The power indicator will light to solid orange. Then wait 
several seconds because buttons may not function for 
these several seconds. 
3. Press the STANDBY/ON button on the projector or remote control. 
The projector lamp will light up and the POWER indicator will begin blinking 
green. When the power is completely on, the indicator will stop blinking light 
green.
To display the picture, select an input signal according to the section "Selecting an 
input signal" (17).
Turning off  the power
1. Press the STANDBY/ON button on the projector or 
remote control.  
The message "Power off?" will appear on the screen for 
approximately 5 seconds.
2. Press the STANDBY/ON button on the projector or 
remote control again while the message is visible.
The projector lamp will go off, and the POWER indicator 
will begin blinking orange. 
Then the POWER indicator will stop blinking and light to 
solid orange when the lamp cooling is complete.
3. Make sure that the power indicator lights to solid orange, set the power switch 
to the OFF position. The POWER indicator will go off. Attach the lens cap.
Power off ?
POWER
(Solid orange)
POWER
(Blinking green)
POWER
(Solid green)
POWER
(Blinking orange)
POWER
(Solid orange) 
						

							
17

Operating
Operating
Adjusting the volume
1. Press the VOLUME button on the remote control.
A dialog will appear on the screen to aid you in adjusting 
the volume.
2. Use the cursor buttons ▲/▼ to adjust the volume.
To close the dialog and complete the operation, press the VOLUME button 
again. Even if you don’t do anything, the dialog will automatically disappear 
after a few seconds. 
Temporarily muting the sound
1. Press the MUTE button on the remote control. 
A dialog will appear on the screen indicating that you have 
muted the sound. 
To restore the sound, press the MUTE or VOLUME button. 
Even if you don’t do anything, the dialog will automatically disappear after a few 
seconds.
Selecting an input signal
1. Press the INPUT button on the projector. 
Each time you press the button, the projector switches its input 
port as below.
             RGB IN1          RGB IN2          DVI-D
          VIDEO  S-VIDEO  COMPONENT VIDEO
1. Press the RGB button on the remote control to select an 
input port for RGB signal.
Each time you press the button, the projector switches its 
RGB input port as below.
RGB IN1  RGB IN2  DVI-D
● When the TURN ON is selected to the item AUTO SEARCH of OPTION menu 
(38), the projector checks the current selected port at fi rst. If no input is 
detected at the port, projector will check other ports in above order.
1. Press the VIDEO button on the remote control to select an 
input for video signal. 
Each time you press the button, the projector switches its 
video input port as below. 
COMPONENT VIDEO  S-VIDEO  VIDEO 
   
● When the TURN ON is selected to the item AUTO SEARCH of OPTION menu 
(38), the projector checks the current selected video port at fi rst. If no input is 
detected at the port, projector will begin to check other ports in above order .detected at the port, projector will begin to check other ports in above order.
STANDBY/ONVIDEO
UP
DOWN
BLANK
ASPECT
PUSH
LASERINDICATOR
LASER
RGB
ENTER
ON
OFF
ESC
POSITION
MAGNIFY
MUTE
KEYSTONE
FREEZE
ONE TOUCH
AUTO PA
GE
MENURESET
VOLUME
MUTE
STANDBY/ONVIDEO
UP
DOWN
BLANK
ASPECT
PUSH
LASERINDICA
TOR
LASER
RGB
ENTER
ON
OFF
ESC
POSITION
MAGNIFY
MUTE
KEYSTONE
FREEZE
ONE TOUCH
AUTO PA
GE
MENURESET
VOLUME
STANDBY/ONVIDEO
UP
DOWN
BLANK
ASPECT
PUSH
LASERINDICA
TOR
LASER
RGB
ENTER
ON
OFF
ESC
POSITION
MAGNIFY
MUTE
KEYSTONE
FREEZE
ONE TOUCH
AUTO PA
GE
MENURESET
VOLUME
UP
STANDBY/ONVIDEO
UP
DOWN
BLANK
ASPECT
PUSH
LASERINDICA
TOR
LASER
RGB
ENTER
ON
OFF
ESC
POSITION
MAGNIFY
MUTE
KEYSTONE
FREEZE
ONE TOUCH
AUTO PA
GE
MENURESET
VOLUME
ST
ANDBY/ON
INPU
T KEYS TONE
RESE
TMENU
POWER T E M P L A M P
             RGB IN1     
          VIDEO 
             RGB IN1                  RGB IN1     
ONE TOUCH 
						

							
18

Operating
Adjusting the zoom and focus
1. Use the zoom knob to adjust the screen size. 
2. Use the focus ring to focus the picture.
Adjusting screen with ONE-TOUCH
1. Press the ONE TOUCH button on the remote control. This 
activates the following functions at one time.
Signal search: Projector will cycle through its input ports in 
order to fi nd any input signal. The search is started from the 
current port. Then when an input is found, the projector will 
stop searching and display the image. If no signal is found, the projector will 
return to the state selected before the operation. 
RGB IN1  RGB IN2  DVI-D  COMPONENT VIDEO  S-VIDEO  VIDEO
   
Auto adjust: Projector automatically adjusts the picture position and size in 
RGB mode, and automatically selects the signal mode in VIDEO input (29).
Automatic keystone distortion correction: Projector automatically corrects 
vertical keystone distortion due to the (forward/backward) setup angle by itself. 
This is only performed if ONE TOUCH of the OPTION menu is set to TURN ON 
(38).
Selecting an aspect ratio
1. Press the ASPECT button on the remote control.  
Each time you press the button, the projector switches the mode for aspect 
ratio in turn. 
At a RGB/DVI signal
NORMAL  4:3  16:9
  
At a video signal/no signal 
4:3  16:9  SMALL
  
● The NORMAL mode keeps the original aspect ratio of the signal.
● At a HDTV signal of 1125i (1080i) or 750p (720p) of COMPONENT VIDEO 
input, only 16:9 mode can be selected.
● Performing the automatic adjustment initializes the aspect ratio setting.
Zoom knobFocus ring
STANDBY/ONVIDEO
UP
DOWN
BLANK
ASPECT
PUSH
LASERINDICATOR
LASER
RGB
ENTER
ON
OFF
ESC
POSITION
MAGNIFY
MUTE
KEYSTONE
FREEZE
ONE TOUCH
AUTO PA
GE
MENURESET
VOLUME
STANDBY/ONVIDEO
UP
DOWN
BLANK
ASPECT
PUSH
LASERINDICA
TOR
LASER
RGB
ENTER
ON
OFF
ESC
POSITION
MAGNIFY
MUTE
KEYSTONE
FREEZE
ONE TOUCH
AUTO PA
GE
MENURESET
VOLUME