Dukane Imagepro 8910 Liquid Crystal Projector Users Manual
Have a look at the manual Dukane Imagepro 8910 Liquid Crystal Projector Users Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 615 Dukane manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
ENGLISH-21
ENGLISH
ENGLISH-21
T T T T
R R R R
O O O O
U U U U
B B B B
L L L L
E E E E
S S S S
H H H H
O O O O
O O O O
T T T T
I I I I
N N N N
G G G G
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Indicators Message
The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Take the
appropriate measures.
Table 10. Indicators Message
POWER
indicatorLAMP
indicator
TEMP
indicatorContents
Lights
orangeTurns offTurns offThe Standby mode has been set.
Blinks
greenTurns offTurns offWarming up. Please wait.
Lights
greenTurns offTurns offON. Normal operation possible.
Blinks
orangeTurns offTurns offCooling. Please wait.
Blinks red--Cooling. Please wait.
The error is found. Take the appropriate measures when the
POWER indicator ceases blinking
Blinks
/Lights redLights
redTurns off
Lamp is not lit.
The interior of the equipment may be too hot. Switch power OFF,
wait 20 minutes until the equipment cools, and check whether the
ventilation openings are blocked, whether the air filter is dirty, or
whether the ambient temperature exceeds 35 °C. And switch
power ON again. Replace the lamp if the same problem occurs.
Blinks
/Lights redBlinks
redTurns off
Lamp or lamp cover is not found, or hasn’t been fitted in correctly.
Switch power OFF, and wait for 45 minutes until the equipment
cools. Check fitting of the lamp and lamp cover, and switch power
ON again. Contact your dealer if the same problem occurs again.
Blinks
/Lights redTurns offBlinks
redThe cooling fan is not operating.
Switch power OFF, and wait for 20 minutes until the equipment
cools. Check for foreign matters in the fan, and switch power ON
again. Contact your dealer if the same problem occurs again.
Blinks
/Lights redTurns offLights red
The interior of the equipment is too hot.
Switch power OFF, and wait for 20 minutes until the equipment
cools. Check whether the ventilation openings are blocked,
whether the air filter is dirty, or whether the ambient temperature
exceeds 35 °C. Then switch power ON again. Contact your dealer if
the same problem occurs again.
Lights
greenBlinks
redBlinks
redThe interior of the equipment is too cool.
Check whether the ambient temperature is below 0°C. Contact your
dealer if the same problem occurs when the ambient temperature is
0~35°C.
When the internal temperature becomes excessive power is switched OFF automatically
for safety reasons, and the indicator is extinguished. Set the power switch to [
O] and wait for 20
minutes until the equipment has cooled sufficiently.
NOTE
$198 1.
ENGLISH-22ENGLISH-22
T T T T
R R R R
O O O O
U U U U
B B B B
L L L L
E E E E
S S S S
H H H H
O O O O
O O O O
T T T T
I I I I
N N N N
G G G G
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Symptom
Before requesting repair, check in accordance with the following chart. If the situation cannot be
corrected, then contact your dealer.
Table 11. Symptom
SymptomPossible causeRemedyPage
The power is not
turned on.
The main power switch is not
turned on.Turn on the main power switch.
8,9The power cord is
disconnected.Plug the power cord into an AC
power outlet.
No video or audio.
The input is not correctly set.Use the projector or remote control
transmitter to set.10
No signal input.Connect correctly.7,8
Video is present but
no audio.
The projector is not correctly
connected.Connect correctly.7,8
The volume is set to minimum.Press VOLUME on the remote
control or display the menu screen
and adjust the volume.11,15
Mute is turned on.Press the MUTE button.11
Audio is present but
no video.
The projector is not correctly
connected.Connect correctly.7,8
The brightness adjustment knob
is rotated fully clockwise.Select BRIGHT with the MENU
button and the press the button.12
The lens cap is still attached.Remove the lens cap.9
Colors are pale and
color matching is
poor.Color density and color
matching are not correctly
adjusted.Adjust the video.12
Images are dark.
Brightness and contrast are not
correctly adjusted.Adjust the video.12
The lamp is nearing the end of
its service life.Replace with a new lamp.17
WHISPER mode is set.Clear WHISPER mode.15
Video is blurred.Focus or H PHASE is out of
adjustment.Adjust the focus or H PHASE.9,12
$198 1.
ENGLISH ENGLISH-23 SPECIFICATIONS SPECIFICATIONS Table 12. Specifications • This specifications are subject to change without notice.NOTE ItemSpecification Product nameLiquid crystal projector Liquid crystal panelPanel size2.3 cm (0.9 type) Drive systemTFT active matrix Pixels786,432 pixels (1024 horizontal x 768 vertical) LensZoom lens F=1.7 ~ 2.1 f=36.8 ~ 47.8 mm Lamp250 W UHB Speaker1.0W+1.0W (stereo) Power supplyAC100 ~ 120V, 4.5A / AC220 ~ 240V, 1.9A Power consumption410W Temperature range0 ~ 35°C (Operating) Size360 (W) x 106 (H) x 256.5 (D) mm Weight (mass)4.3 kg RGB signal input RGB IN1Video: Analog 0.7Vp-p, 75Ωterminator (positive) H/V. sync.: TTL level (positive/negative) Composite sync.: TTL level D-sub 15-pin shrink jack 2 DVITMDS, DC: 150~1200 mV / AC: 1.56 Vp-p TTL Level (Positive/Negative) AUDIO IN RGB1200mVrms, 50 kΩ(max. 3.0Vp-p) Stereo mini jackDVI RGB2 Video signal input VIDEO IN1.0Vp-p, 75Ωterminator RCA jack S-VIDEO IN Brightness signal: 1.0Vp-p, 75Ωterminator Color signal: 0.286Vp-p (NTSC, burst signal),75Ωterminator 0.300Vp-p (PAL/SECAM, burst signal),75Ωterminator Mini DIN 4-pin jack COMPONENT VIDEOY1.0 Vp-p, 75 ΩTerminator (Positive) CB/CR0.7 Vp-p, 75 ΩTerminator (Positive) PB/PR0.7 Vp-p, 75 ΩTerminator (Positive) AUDIO INL200mVrms, 50 kΩ(max. 3.0Vp-p) RCA jack R Signal outputRGB OUT Video: Analog 0.7Vp-p, 75Ωoutput impedance (positive) H/V. sync.: TTL level (positive/negative) Composite sync.: TTL level D-sub 15-pin shrink jack AUDIO OUT200mVrms, output impedance 1 kΩ(max. 3.0Vp-p) Stereo mini jack Control functionsCONTROLD-sub 15-pin shrink plug USBUSB jack (B type) Optional PartsLamp: DT00471 Air Filter: NJ06131 * For others, consult your dealer. $198 1.
ENGLISH-24ENGLISH-24 WARRANTY AND AFTER-SERVICE WARRANTY AND AFTER-SERVICE If a problem occurs with the equipment, first refer to the P.20 “TROUBLESHOOTING” section and run through the suggested checks. If this does not resolve the problem contact your dealer or service company. They will tell you what warranty condition is applied. $198 1.
Pin NoSignalPin NoSignalPin NoSignal 1Video input Red9- 15 RGB IN 1: SCL(DDC) 2Video input Green10GroundRGB IN 2: - 3Video input Blue11-RGB OUT: - 4- 12 RGB IN 1: SDA(DDC) 5GroundRGB IN 2: - 6Ground RedRGB OUT: - 7Ground Green13H. sync./ Composite sync. 8Ground Blue14Vertical sync TECHNICAL - 1 TECHNICAL TECHNICAL TECHNICAL Dimension Diagram 6%*0 */6%*0 */$313$0.10/&/57*%&0 3(#*/ 3(#065 $0/530-%7*$#1#:36%*0065 64# -7*%&0*/47*%&0*/ 108.4 360 266 112.5 49.7 62.8 106256.5 Unit : mm 3. Mini Din 4-pin Connector (S-VIDEO) Pin NoSignal 1Color:0.286Vp-p (NTSC, burst signal),75Ωterminator 0.300Vp-p (PAL/SECAM, burst signal),75Ωterminator 2Brightness:1.0Vp-p, 75Ωterminator 3Ground 4Ground Signal Connector Pin Assignment 1. D-sub 15-pin Shrink Connector (RGB IN 1/RGB IN 2/RGB OUT) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Pin NoSignalPin NoSignalPin NoSignal 1T.M.D.S. Data 2 -11T.M.D.S. Data 1 / 3 Shield21- 2T.M.D.S. Data 2 +12-22T.M.D.S. Clock Shield 3T.M.D.S. Data 2 / 4 Shield13-23T.M.D.S. Clock + 4-14+5V Power24T.M.D.S. Clock - 5-15Ground (+5V, Analog H/V Sync.) 6DDC Clock16Hot-Plug Sense 7DDC Data17T.M.D.S. Data 0 - 8Analog V. Sync.18T.M.D.S. Data 0 + 9T.M.D.S. Data 1 -19T.M.D.S. Data 0 / 5 Shield 10T.M.D.S. Data 1 +20- 2. Digital Receptacle Connector (DVI) 1234 5678 9 101112 13141516 17 18 19 20 21 22 23 24 $198 1.
TECHNICAL - 2 T T T T E E E E C C C C H H H H N N N N I I I I C C C C A A A A L L L L( ( ( ( c c c c o o o o n n n n t t t t i i i i n n n n u u u u e e e e d d d d ) ) ) ) Example of computer signal • Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector. • Be sure to check jack type, signal level, timing and resolution before connecting this projector to a computer. • Depending on the input signal, full-size display may not be possible in some cases. Refer to the number of display pixels above. • The image may not be displayed correctly when the input sync. signal is Composite Sync. or Sync. on G. • The image might be something wrong with computer by computer on the DVI mode. In the case, it is recommended to reduce the resolution and / or reflesh rate.NOTE Resolution H × × VfH (kHz)fV (Hz)RatingSignal modeDisplay mode 640 ×35037.985.1VESAVGA-1Zoom in 640 ×40037.985.1VESAVGA-2Zoom in 720 ×40037.985.0VESATEXTZoom in 640 ×48031.559.9VESAVGA (60Hz)Zoom in 640 ×48035.066.7Mac13modeZoom in 640 ×48037.972.8VESAVGA (72Hz)Zoom in 640 ×48037.575.0VESAVGA (75Hz)Zoom in 640 ×48043.385.0VESAVGA (85Hz)Zoom in 800 ×60035.256.3VESASVGA (56Hz)Zoom in 800 ×60037.960.3VESASVGA (60Hz)Zoom in 800 ×60048.172.2VESASVGA (72Hz)Zoom in 800 ×60046.975.0VESASVGA (75Hz)Zoom in 800 ×60053.785.1VESASVGA (85Hz)Zoom in 832 ×62449.774.5Mac16mode 1024 ×76848.460.0VESAXGA (60Hz) 1024 ×76856.570.1VESAXGA (70Hz) 1024 ×76860.075.0VESAXGA (75Hz) 1024 ×76868.785.0VESAXGA (85Hz) 1152 ×86467.575.0VESASXGA (75Hz)Zoom out 1280 ×96060.060.0VESASXGA (60Hz)Zoom out 1280 ×102464.060.0VESASXGA (60Hz)Zoom out 1280 ×102480.075.0VESASXGA (75Hz)Zoom out $198 1.
TECHNICAL - 3 TECHNICAL T T T T E E E E C C C C H H H H N N N N I I I I C C C C A A A A L L L L( ( ( ( c c c c o o o o n n n n t t t t i i i i n n n n u u u u e e e e d d d d ) ) ) ) Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, refer to adjust the V.POSIT and H.POSIT of the menu. DATA HSYNCDATA VSYNCDisplay interval c Back porch b Sync aFront porch d Display interval c Back porch b Sync aFront porch d Computer / SignalHorizontal signal timing (µs) abcd VGA-1 (85Hz)2.03.020.31.0 VGA-2 (85Hz)2.03.020.31.0 TEXT2.03.020.31.0 VGA (60Hz)3.81.925.40.6 Mac 13mode2.13.221.22.1 VGA (72Hz)1.33.820.31.0 VGA (75Hz)2.03.820.30.5 VGA (85Hz)1.62.217.81.6 SVGA (56Hz)2.03.622.20.7 SVGA (60Hz)3.22.220.01.0 SVGA (72Hz)2.41.316.01.1 SVGA (75Hz)1.63.216.20.3 SVGA (85Hz)1.12.714.20.6 Mac 16mode1.13.914.50.6 XGA (60Hz)2.12.515.80.4 XGA (70Hz)1.81.913.70.3 XGA (75Hz)1.22.213.00.2 XGA (85Hz)1.02.210.80.5 1152×864 (75Hz)1.22.410.70.6 1280×960 (60Hz)1.02.911.90.9 1280×1024 (60Hz)1.02.311.90.4 1280×1024 (75Hz)1.11.89.50.1 Computer / SignalVertical signal timimg (lines) abcd VGA-1 (85Hz)36035032 VGA-2 (85Hz)3414001 TEXT3424801 VGA (60Hz)23348010 Mac 13mode3394803 VGA (72Hz)3284809 VGA (75Hz)3164801 VGA (85Hz)3254801 SVGA (56Hz)2226001 SVGA (60Hz)4236001 SVGA (72Hz)62360037 SVGA (75Hz)3216001 SVGA (85Hz)3276001 Mac 16mode3396241 XGA (60Hz)6297683 XGA (70Hz)6297683 XGA (75Hz)3287681 XGA (85Hz)3367681 1152×864 (75Hz)3328641 1280×960 (60Hz)3369601 1280×1024 (60Hz)33810241 1280×1024 (75Hz)33810241 $198 1.
TECHNICAL - 4 T T T T E E E E C C C C H H H H N N N N I I I I C C C C A A A A L L L L( ( ( ( c c c c o o o o n n n n t t t t i i i i n n n n u u u u e e e e d d d d ) ) ) ) Connection to the Mouse Control 1. PS/2, ADB or Serial Mouse (1) Turn off the projector and computer, and connect the two units with the appropriate cable. For PS/2 mouse control (for IBM and compatible), use the enclosed mouse cable. For others, consult your dealer. (2) Disconnect the USB cable from the projector if it is connected. Then turn on the projector. (3) Turn on the computer. (4) Start the mouse function. If the mouse has not been started, reboot the computer (soft reboot or reboot buttons). Refer to the descriptions of “DISC PAD” and “MOUSE/RIGHT button” of page 4. 2. USB Mouse (1) Connect the projector and computer with a suitable commercially available USB cable. Consult your dealer to get the cable, if you need. (2) Start the mouse function. Refer to the descriptions of “DISC PAD” and “MOUSE/RIGHT button” of page 4. • Before connecting, read the instruction manuals of the devices to be connected. • In the case of notebook type computers with an internal pointing device, the mouse control function will not work unless the internal pointing device is disabled. In such case, disable the internal pointing device and change the BIOS setting to select an external mouse before the operations described in (1) to (4) above. Also, some computers may not have a utility program to operate a mouse. Refer to the computer hardware manual for detail. NOTE PS/2 Mouse 2 1 4 3 6 5 2 1 4 3 6 5 8 7 10 9 12 11 14 13 15 CLK D ATA SEL0 RTS GND+5VD ATA GND +5V CLK 21 43 65 Mouse jack Mini DIN 6-pin Projector Computer 123 4 5 6 78 910 11 12 13 14 15 CONTROL Terminal D-sub 15-pin shrink jack $198 1.
TECHNICAL - 5 T T T T E E E E C C C C H H H H N N N N I I I I C C C C A A A A L L L L( ( ( ( c c c c o o o o n n n n t t t t i i i i n n n n u u u u e e e e d d d d ) ) ) ) TECHNICAL 1 2 3 4 1 2 3 4 +5V — DATA +DATA GND +5V — DATA +DATA GND 1 234 2 1 3 4 USB jack (B type) USB jack (A type)Projector USB cable Computer ADB Mouse 2 1 4 3 6 5 2 1 4 3 8 7 10 9 12 11 14 13 15 RTS GND+5VADB GND+5V ( POWER ON) D ATA 21 43 Mouse jack Mini DIN 4-pin Projector Computer 123 4 5 6 78 910 11 12 13 14 15 CONTROL Terminal D-sub 15-pin shrink jack Serial Mouse 2 1 4 3 6 5 2 1 4 3 6 5 8 7 10 9 8 7 9 12 11 14 13 15 RICD RD TD DTR GND DSR CTS RTS RTS GND SEL0 TD 2143 6 5 897 Mouse jack D-sub 9-pin Projector Computer 123 4 5 6 78 910 11 12 13 14 15 CONTROL Terminal D-sub 15-pin shrink jack USB Mouse $198 1.
TECHNICAL - 6 T T T T E E E E C C C C H H H H N N N N I I I I C C C C A A A A L L L L( ( ( ( c c c c o o o o n n n n t t t t i i i i n n n n u u u u e e e e d d d d ) ) ) ) RS-232C communication (1) Turn off the projector and computer power supplies and connect with the RS-232C cable. (2) Turn on the computer power supply and, after the computer has started up, turn on the projector power supply. 1 2 3 4 5 6 7 8 910 11 12 13 14 15 Control jack D-sub 15-pin shrink jack1234567891011121314 15RD TD GND SELO RTS 12345678 9 CD RD TD DTR GND DSR RTS CTS RI12345 67 8 9 RS-232C jack D-sub 9-pin Projector Computer Communications setting 19200bps, 8N1 1 Protocol Consist of header (7 bytes) + command data (6 bytes). 2 Header BE + EF + 03 + 06 + 00 + CRC_low + CRC_high CRC_low : Lower byte of CRC flag for command data. CRC_high : Upper byte of CRC flag for command data. 3 Command data byte_0byte_1byte_2byte_3byte_4byte_5 ActionTypeSetting code lowhighlowhighlowhigh Command data chart Action (byte_0 - 1) ActionClassificationContent 1SETChange setting to desired value. 2GETRead projector internal setup value. 4INCREMENTIncrement setup value by 1. 5DECREMENTDecrement setup value by 1. 6EXECUTERun a command. $198 1.