Dukane Imagepro 8909 Liquid Crystal Projector Users Manual

							ItemDescription
VOLUMEVolume Adjustment :Press the VOLUME / button.
MUTE (*)Set/Clear Mute Mode :Press the MUTE button. No sound is heard in the
MUTE mode.
AUTO
Automatic Adjustment at RGB Input :Press the AUTO button. Horizontal
position(H.POSIT), vertical position (V.POSIT),clock phase (H.PHASE), and
horizontal size(H.SIZE) are automatically adjusted. Use with the window at
maximum size in the application display.
Automatic Adjustment at Video Input :Press the AUTO button. A signal
type appropriate for the input signal is selected automatically. Valid only
when AUTO is set for VIDEO on the menu.
• This operation requires approximately ten seconds. It may not function correctly
with some input signals.
BLANK
ON/OFFSet/Clear Blank Mode:Press the BLANK button. No image is displayed in
the Blank mode. The screen color is as set in BLANK on the Image menu.
MENU
ON/OFF (
*)
Menu Display Start/Stop:Press the MENU button.• The menu display is terminated automatically after approximately ten seconds of
inactivity.
MENU
SELECT
Select Menu Type:Press the MENU SELECT button. Allows the user to
select the normal menu or the single menu. Only the selected item is
displayed on the single menu, and other items are displayed with the 
and  buttons as with the normal menu.
• Valid only when the Setup menu is used. Push the MENU SELECT button after
selecting items such as BRIGHTNESS.
• The MENU SELECT button may operate as the mouse control button. Refer to
page 4.
Normal menu Single menu
P.IN P.
MODESelect Mode of P.IN P. Display :Press the PinP button.
Small
→Large→P.IN P.off (→Small)
• Valid only at RGB IN 1, RGB IN 2 or DIGITAL input.
ZOOMAdjust Screen Size :Press the ZOOM  /  button.
FOCUSAdjust Focus :Press the FOCUS  /  button.
ENGLISH-11
ENGLISH
ENGLISH-11
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Items indicated by (*) may be used from the control panel.
Table 3. Basic Operation (continued)
CONTRAST-2
BRIGHT
CONTRAST
V POSIT
H POSIT
H PHASE
H SIZE
COLOR BAL R
COLOR BAL B
ASPECT0
-2
+1 
0
0 100
100
800SETUP INPUT OPT.IMAGE(MENU SELECT) 
						

							ENGLISH-12ENGLISH-12
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Setup MenuThe following adjustments and settings are possible
when SETUP is selected at the top of the menu. Part
of the Setup menu differs between RGB input and
video input. Select an item with the  and
buttons, and start operation. Use the Single menu to
reduce menu size (see Table 3, MENU SELECT).
Table 4. Setup Menu
VIDEO
S-VIDEO
COMPONENT VIDEO RGB IN 1
RGB IN 2
DIGITAL
BRIGHT
CONTRAST
V POSIT
H POSIT
H PHASE
H SIZE
COLOR BAL R
COLOR BAL B
ASPECT0
-2
+1 
0
0 100
100
800SETUP INPUT OPT.IMAGEBRIGHT
CONTRAST
SHARPNESS
COLOR
TINT
COLOR BAL  R
COLOR BAL  B
ASPECT0
+1
+1
0
0
0
0SETUP INPUT OPT.IMAGE
ItemDescriptionRGB IN 1
RGB IN 2DIGTALVIDEOS-VIDEOCOMPONENT
BRIGHTAdjustment: Dark ↔Light ✔✔✔
CONTRASTAdjustment:Weak ↔Strong ✔✔✔
V POSITAdjustment:Down ↔Up ✔--
H POSITAdjustment:Left ↔Right ✔--
H PHASEAdjustment:Left ↔Right 
• Adjust to eliminate flicker.✔--
H SIZE
Adjustment:Small ↔Large • The image may not be displayed correctly if the horizontal
size is excessive. In such cases, press the RESET button,
and initialize the horizontal size.✔--
SHARPNESSAdjustment:Soft ↔Clear --✔
COLORAdjustment:Light ↔Dark --✔
TINTAdjustment:Red ↔Green • Valid only when NTSC or NTSC 4.43 signal is received.--✔
COLOR BAL RAdjustment:Light ↔Dark ✔✔✔
COLOR BAL BAdjustment:Light ↔Dark ✔✔✔
ASPECT
Select Image Aspect Ratio :4:3[ ] ↔
16:9[ ]
Select Position of Image:
Press the  button while 16:9[ ] is selected.
Center
→Down →Up (→Center )
✔✔-
Select Image Aspect Ratio:
4:3[ ] ↔16:9[ ] ↔4:3 small[ ]
Select Position of Image :
Press the  button while 16:9[ ] / 4:3 small[ ]
is selected.
Center
→Down→Up (→Center )• 4:3 small may not be displayed correctly with some input
signals.
--✔ 
						

							ENGLISH-13
ENGLISH
ENGLISH-13
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Input MenuThe following functions are available when INPUT is selected on the
menu. Select an item with the and buttons, and start or stop
operation with the and buttons. The function indicated (**) are
effective on video input mode only, not on RGB input mode, except in
the P.IN P. window on RGB input mode.
Table 5. Input Menu
EXECUTE
CANCELAUTO
RGB
VIDEO
VIDEO NR
Progressive
BLACK SETUP INPUT OPT.IMAGE
ItemDescription
AUTO
Automatic Adjustment at RGB Input: Select the EXECUTE with the
button.Horizontal position (H.POSIT), vertical position (V.POSIT), clock
phase (H.PHASE), and horizontal size (H.SIZE) are automatically adjusted.
Use with the window at maximum size in the application display.
Automatic Adjustment at Video Input: Select the EXECUTEwith the 
button. A signal type appropriate for the input signal is selected
automatically when 
EXECUTEis selected automatically. Valid only when
AUTO is set for VIDEO on the menu.
• This operation requires approximately 10 seconds. It may not function correctly with
some input signals. Pressing the AUTO button in this case may correct this problem.
• This function is the same as for the AUTO function in Basic operation.
RGB
Displays RGB Input Frequency:Displays the horizontal and vertical sync
signal frequencies for RGB input.
• Valid only at RGB input.
VIDEO (**)
Select Video Signal Type:Select the signal type with the  and 
buttons. Select NTSC, PAL, SECAM, NTSC4.43, M-PAL, or N-PAL as
appropriate for the input signal. The selection of AUTO enables and
executes the function AUTO (Automatic Adjustment at Video Input), except
for the N-PAL input.
• Use this function when the image becomes unstable (eg. the image becomes
irregular, or lacks color) at VIDEO/S-VIDEO input.
• Automatic Adjustment requires approximately ten seconds. It may not function
correctly with some input signals. Pressing the AUTO button in this case may correct
this problem except for the N-PAL input.
• For the COMPONENT VIDEO input, this function is not effective and the signal type
is distinguished automatically. Refer to the item HDTV of the OPT. Menu for the
signal of HDTV.
VIDEO NR
(**)
Set/Clear Noise Reduction Mode:Select the TURN ON / TURN OFF with
the  / button. When the TURN ON is selected, the NR mode is active
and the noise on screen of the video input will be reduced.
Progressive
(**)
Select Progressive Mode:Select the mode suitable for the input signal
with the  and  buttons. The TV mode and the CINEMA mode convert
the interlaced video signal into the progressive signal. The CINEMA mode is
adptable 2-3 Pull-Down system to the conversion.
• Use this function to raise resolution, at the interlaced video input except HDTV
signal.
BLACK(**)
Set/Clear Black Enhancement Mode:Select the TURN ON / TURN OFF
with the  / button. When the TURN ON is selected, the black
enhancement mode is active and the contrast ratio of the screen for the
video input will be raised by making black level darker. 
						

							ENGLISH-14ENGLISH-14
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Image Menu
The following adjustments and settings are available when IMAGE is
selected on the menu. Select an item with the and buttons, and 
start operation.
Table 6. Image Menu
KEYSTONE
BLANK
MIRROR
START UP
P. IN P.+1 SETUP INPUT OPT.IMAGE
ItemDescription
KEYSTONE
Keystone Adjustment:
Reduce size of bottom of image ↔Reduce size of top of image • When this function is activated, the image may not be displayed correctly with
some input signals.
BLANKSelect Blank Screen Color:Select color with the  and  buttons.• The image is cleared when the BLANK mode is set with BLANK ON, or when there
is no signal, and the entire screen is displayed in the selected color.
MIRROROperation Start/Stop:Press the  or  button.
Select Mirror Status:Select mirror status with  and  buttons.
START UP
Operation Start/Stop:Press the  or  button.
Setup Initial Screen Display:Select TURN ON with the  button.
Clear Initial Screen Display:Select TURN OFF with the  button.• Note that if TURN OFF is selected the blank screen is displayed in blue when there
is no signal.
P. IN P.
Operation Start/Stop:Press the or button.
Select Position of P. in P. Display :Press the or button.
↔↔↔(↔)
• Valid only at RGB IN 1, RGB IN 2 or DIGITAL input. 
						

							ENGLISH-15
ENGLISH
ENGLISH-15
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Options Menu
The following adjustments and settings are available when OPT. is
selected on the menu. Select an item with the and buttons, and
start operation. The function indicated (**) are effective on video input
mode only, not on RGB input mode, except in the P.IN P. window on
RGB input mode.
Table 7. Options Menu
VOLUMEMENU COLORLANGUAGE
AUTO OFF
SYNC ON G
HDTV16
SETUP INPUT OPT.IMAGE
ItemDescription
VOLUMEVolume Adjustment:Reduce VOLUME ↔Increase VOLUME 
MENU COLORSelect Menu Background Color:Select with the  and  buttons.
LANGUAGEOperation Start/Stop:Press the  or  button.
Select Menu Display Language:Select with the  and  buttons.
AUTO OFF
Operation Start/Stop:Press the  or  button.
Set AUTO OFF:Set 1~99 minutes with the  and  buttons. The
system automatically enters the standby mode when a signal is not
received for the set time.
Clear AUTO OFF:Select STOP (0 min.) with the  button. When
STOP is selected the system does not enter the standby mode even if
no signal is received.
SYNC ON G
Operation Start/Stop:Press the  or  button.
SYNC ON G Valid:Select TURN ON with the  button.
SYNC ON G Invalid:Select TURN OFF with the  button.• May not be displayed correctly with some input signals when SYNC ON G is
valid. In such cases, remove the signal connector so that no signal is received,
set SYNC ON G to invalid, and reconnect the signal.
HDTV(**)Select HDTV mode:Select the 1035i mode or 1080i mode suitable for
the input signal with the  /  button.  
						

							ENGLISH-16ENGLISH-16
O O O O
P P P P
E E E E
R R R R
A A A A
T T T T
I I I I
O O O O
N N N N
S S S S
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
No Signal Menu
The same adjustments and settings are available as with the Image and
Options menus when the MENU button is pressed during display of the
“NO INPUT IS DETECTED ON ***” or “SYNC IS OUT OF RANGE
ON ***” message while no signal is received.
Table 8. No Signal Menu
VOLUME
KEYSTONE
BLANK
MIRROR
START UP
MENU COLORLANGUAGE
AUTO OFF
SYNC ON G16
+1
ItemDescription
VOLUME
Volume Adjustment:Reduce VOLUME ↔Increase VOLUME • When this function is used, audio input is automatically switched to video. The
audio input can be switched by moving the DISK PAD left and right during the
display of the volume adjustment bar. The volume adjustment bar is displayed by
pressing VOLUME  or VOLUME  button.
KEYSTONEKeystone Adjustment:Reduce the size of bottom of image ↔
Reduce the size of top of image 
BLANK
Select Blank Screen Color:Select the color with the  and 
buttons.
• When the blank mode is set with BLANK ON, by absence of a signal, or by
input of a non-standard signal, the image is cleared and the complete screen is
displayed in the selected color.
MIRROROperation Start/Stop:Press the  or  button.Select Mirror Status:Select the mirror status with the  and 
buttons.
START UP
Operation Start/Stop:Press the  or  button.Setup Initial Screen Display:Select the TURN ON with the  button.Clear Initial Screen Display:Select the TURN OFF with the  button.• Note that if TURN OFF is selected the blank screen is displayed in blue when
there is no signal.
MENU COLORSelect Menu Background Color:Select the color with the  and 
buttons.
LANGUAGE
Operation Start/Stop:Press the  or  button.Select Menu Display Language:Select the language with the  and
buttons.
AUTO OFF
Operation start/stop:Press the  or  button.Set AUTO OFF:Set 1~99 minutes with the  and  buttons. The
system automatically enters the standby mode when a signal is not
received for the set time.
Clear AUTO OFF:Select the STOP (0 min.) with the  button. When
the STOP is selected the system does not enter the standby mode even
if no signal is received.
SYNC ON G
Operation Start/Stop:Press the  or  button.SYNC ON G Valid:Select the TURN ON with the  button.SYNC ON G Invalid:Select the TURN OFF with the  button.• May not be displayed correctly with some input signals when the SYNC ON G
is valid. In such cases, remove the signal connector so that no signal is received,
set the SYNC ON G to invalid, and reconnect the signal. 
						

							ENGLISH-17
ENGLISH
ENGLISH-17
MAINTENANCE MAINTENANCE
Lamp
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
Contact your dealer before replacing the lamp.
For the optional lamp, see the item “Option Parts” of the Table 12.
Before replacing the lamp, switch power OFF, remove the power cord from the power outlet, and
wait approximately 45 minutes until the lamp has cooled. The lamp may explode if handled at high
temperatures.
Lamp Life
Projector lamps have a finite life. The image will become darker, and hues will become weaker,
after a lamp has been used for a long period of time. 
Replace the lamp if the LAMP indicator is red, or the CHANGE THE LAMP message appears
when the projector is switched ON. See Table 9 of P.20 and Table 10 of P.21.
•The LAMP indicator is also red when the lamp unit reaches high temperature. Before
replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again.
If the LAMP indicator is still red, replace the lamp.NOTE
Lamp
Front
glasss Reflector
WARNING• For disposal of used lamp, treat
according to the instruction of community
authorities.
• Since the lamp is made of glass, do not apply shock
to it and do not scratch it.
• Also, do not use old lamp. This could also cause
explosion of the lamp.
• If it is probable that the lamp has exploded (explosive
sound is heard), disconnect the power plug from the
power outlet and ask your dealer to replace lamp. The
lamp is covered by front glass , but, in rare cases, the
reflector and the inside of the projector may be
damaged by scattered broken pieces of glass, and
broken pieces could cause injury when being handled.
• Do not use the projector with the lamp cover removed. 
						

							ENGLISH-18ENGLISH-18
M M M M
A A A A
I I I I
N N N N
T T T T
E E E E
N N N N
A A A A
N N N N
C C C C
E E E E
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Replacing the Lamp
1. Switch the projector OFF, remove the power cord from the
power outlet, and wait at least 45 minutes for the unit to cool.
2. Prepare a new lamp.
3. Check that the projector has cooled sufficiently, and gently
turn it upside down.
4. Loosen the screw as shown in the diagram, and remove the
lamp cover.
5. Loosen the two screws, and gently remove the lamp while
holding the grips. Touching the inside of the lamp case may
result in uneven coloring.
6. Install the new lamp and tighten the two screws firmly. Also
steadily push the opposite side of the screwed lamp into the
unit.
7. Replace the lamp cover in position and tighten the screw
firmly.
8. Gently turn the projector right-side up.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp. When the lamp has been replaced after the LAMP
indicator is red, or the CHANGE THE LAMP message is displayed, complete the following
operation within ten minutes of switching power ON. The power will be turned off automatically in
over 10 minutes.
1. Switch power ON, and press the RESET button, for approximately three seconds. The ‘LAMP
xxxx hr’ message will appear on the lamp timer on the bottom of the screen.
2. Press the MENU button on the remote control transmitter, or the RESET button on the control
panel, while the lamp timer is displayed. The ‘LAMP xxxx 
→0 CANCEL’ message will
then appear.
3. Press the  and select 0, and wait until the timer display is cleared.
•Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always
when replacing the lamp. The message functions will not operate  properly if the lamp timer is not
reset correctly.NOTE
CAUTION• Ensure that screws are tightened
properly. Screws not tightened fully may result
in injury or accidents.
• Do not use the projector with the lamp cover
removed. 
						

							ENGLISH-19
ENGLISH
ENGLISH-19
M M M M
A A A A
I I I I
N N N N
T T T T
E E E E
N N N N
A A A A
N N N N
C C C C
E E E E
       
( ( ( (
c c c c
o o o o
n n n n
t t t t
i i i i
n n n n
u u u u
e e e e
d d d d
) ) ) )
Air Filter Maintenance
The air filter should be cleaned as described below at intervals of approximately 100 hours.
1. Switch the projector power supply OFF, and remove the power cord from the power outlet.
2. Clean the air filter with a vacuum cleaner.
Other Maintenance
Maintenance Inside the Equipment
For safety reasons, ensure that the equipment is cleaned and checked by the dealer once every two
years. Maintaining the equipment by yourself is dangerous.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Cabinet and Remote control transmitter
Gently wipe with a soft cloth. If dirt and stains etc. are not easily removed, use a soft cloth
dampened with water, or water and a neutral detergent, and wipe dry with a soft, dry cloth.
CAUTION• Switch power OFF and remove the power cord from the power
outlet before beginning maintenance work. Please read the separate “SAFETY
INSTRUCTIONS” thoroughly to ensure that maintenance is performed correctly.
• Do not use detergents or chemicals other than those noted above (e.g. benzene
or thinners).
• Do not use cleaning sprays.
• Do not rub with hard materials, or tap the equipment.
CAUTION• Switch power OFF and remove the power cord from the power
outlet before beginning maintenance work. Please read the separate “SAFETY
INSTRUCTIONS” thoroughly to ensure that maintenance is performed correctly.
• Replace the air filter if contamination cannot be removed, or if it is damaged.
Contact your dealer in such case. For the optional air filter, see the item “Option
Parts” of the Table 12. 
• Do not use the equipment with the air filter removed.
• When the air filter is clogged with dust etc. the power supply is switched OFF
automatically to prevent the temperature rising inside the projector. 
						

							ENGLISH-20ENGLISH-20
TROUBLESHOOTING TROUBLESHOOTING
OSD Message
The messages as described below may appear on the screen at power ON. Take the appropriate
measures when such a message appears.
Table 9. OSD Messages
MessageContents
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
*1)
The message shown at left appears after the lamp has
been used for more than 1300 hours.
The lamp is approaching the end of its life.
Power is switched OFF automatically when the lamp
reaches the end of its life. Prepare a new lamp for
installation.
Always reset the lamp timer after replacing the lamp.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL TURN OFF
AFTER 
**hr.*1)
The lamp will reach the end of its life in **hours.
Power will be switched OFF automatically in 
**hours.
Replace the lamp as shown in P.17~18 “Lamp”.
Always reset the lamp timer after replacing the lamp.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL 
TURN OFF
AFTER 0 hr.The lamp has reached the end of its life. Power will be
switched OFF in a few minutes.
Switch power OFF immediately and replace the lamp as
shown in P.17~18 “Lamp”.
Always reset the lamp timer after replacing the lamp.
NO INPUT IS DETECTED
ON ***No input signal found.
Check signal input connections and signal sources.
SYNC IS OUT OF RANGE
ON ***
The horizontal or vertical frequency of the input signal is
not within the specified range.
Check the specifications of the equipment and the signal
source.
*1) This message is cleared automatically after approximately three minutes, and appears
every time power is switched ON.NOTE