Dukane Imagepro 8801a Lcd Projector Users Manual

							13
1Remove the battery
cover
Push the knob while lifting
up the battery cover in the
direction of the arrow.
Insert the batteries
Align and insert the two AA
batteries (that came with the
projector) according to their plus
and minus terminals (as indicated
in the remote control).
Close the battery
cover
Replace the battery cover
in the direction of the arrow
and snap it back into place.
• The remote control works with both the
projectors front and rear remote sensors.
• The range of the remote sensor on the front and
back is 3 meters with a 60-degree range (30
degrees to the left and right of the remote sensor).
• Since the remote control uses infrared light to send
signals to the projector (Class 1 LED), be sure to
use the remote control in an area free from
obstacles that could block the remote controls
output signal to the projector.
approximately
3 metersapproximately
3 meters
30 degrees30 degrees30 degrees30 degrees
23
USING THE REMOTE CONTROL
CAUTIONPrecautions to observe in regards to the batteries
Always handle the batteries with care and use them only as directed. Improper use may result in
battery cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.
• Keep the battery away from children and pets.
• 
Be sure to use only the batteries specified for use with the remote control. Do not mix new batteries with used ones.
• When inserting batteries, verify that the plus and minus terminals are aligned correctly (as indicated in the remote control).
• When you dispose the battery, you should obey the law in the relative area or country.
Precautions to observe when using the remote control
• Do not drop or otherwise expose the remote control to physical impact.
• 
Do not get the remote control wet or place it on wet objects. Doing so may result in malfunction.
• Remove the batteries from the remote control and store them in a safe place if you
wont be using the remote control for an extended period. 
• Replace the batteries whenever the remote control starts to malfunction.
• 
When strong light, such as direct sunlight or light from an extremely close range (such as from an
inverter fluorescent lamp), hits the projectors remote sensor, the remote control may cease to function.
Adjust the direction of the projector to keep light from directly hitting the projectors remote sensor.
ATTENTION
Putting batteries into the remote control unit
Operating the remote control
• Only use the accompanying remote control. Using other remote controls (even of similiar models) to control the
CP-X385W may result in unexpected operation.
$19&/7	4
 
 
 
 1.
 
 
						

							14
1Make sure that the power cord is firmly and
correctly connected to the projector and outlet
2Turn on the projectors power
Set the power switch to [ | ] (ON). The projector will go
to STANDBY mode and the POWER indicator will light to
solid orange.
3Press the STANDBY/ON button (control
panel or remote control) 
• The projector begins warming up and the POWER
indicator blinks green.
• The POWER indicator stops blinking and
lights to solid green once the projectors
power is completely on.
4Remove the lens cap
The picture is projected.
POWER-indikator
STANDBY/ON

STANDBY/ONLASERBLANK
RGBVIDEO
TURNING ON THE POWER
Control panel
Precautions 
Connect all devices to be used to the projector prior to turning on the power.™
WARNINGWhen the power is ON, a strong light is emitted. Do not look into the
lens.
Turn the
power on/off in
right order.
• Power on the
projector before the
computer or video
tape recorder.
• Power off the
projector after the
computer or video
tape recorder.
NOTE
på/av-bryter
$19&/7	4
 
 
 
 1.
 
 
						

							RGB
15
6Use the zoom ring to adjust the
screen size
7Use the focus ring to focus the
picture
5
If selecting RGB input
Press the RGB button
Press this button to toggle between the
devices connected to RGB IN 1 and 2.
As illustrated below, each time you
press the RGB button, the projector
switches between RGB IN 1 and 2.
Select the signal you wish to project.
If selecting video input
Press the VIDEO button
Press this button to toggle between the
devices connected to VIDEO IN, S-
VIDEO IN and COMPONENT VIDEO. As
illustrated below, each time you press
the VIDEO button, the projector
switches between VIDEO IN, S-VIDEO
IN and COMPONENT VIDEO. Select the
signal you wish to project.
Using the remote control
Press the INPUT button
As illustrated below, each time you
press the INPUT button, the projector
switches between its input signal
ports. Select the signal you wish to
project.
Using the projectors control panel
VIDEO
RGB IN 1 RGB IN 2 VIDEO IN
S-VIDEO IN COMPONENT VIDEO
VIDEO IN S-VIDEO IN
COMPONENT VIDEO
RGB IN 1 RGB IN 2
INPUT
Selecting an Input Signal
$19&/7	4
 
 
 
 1.
 
 
						

							16
STANDBY/ONLASERBLANK
RGBVIDEO
AUTO
MENU
ENTER
KEYSTONE
RESET
FREEZE ASPECT
ESC
MAGNIFY
POSITION
OFF ONVOLUME
MUTE
1Press the STANDBY/ON button (control
panel or remote control)
The message Power off? will appear on the screen for approximately 5 seconds. 
3Check that the POWER indicator stops
blinking and lights to solid orange.
Switch the power switch to [O] (OFF).
4Confirm that the POWER indicator has
gone off and then attach the lens cap.
When the projector has completed powering down, the
POWER indicator will go off.
STANDBY/ON
TURNING OFF THE POWER
Control panel
2Press the STANDBY/ON button again
(control panel or remote control)
Press the STANDBY/ON button again while the Power off?
message is visible. The projector lamp goes off and starts cooling
down. The POWER indicator blinks orange while the lamp cools
down. (Pressing the STANDBY/ON button while the POWER
indicator is blinking orange has no effect.)
The system goes into the STANDBY mode after cooling
down and the POWER indicator stops blinking
orange and then lights to solid orange.
STANDBY/ON
• Except in
emergencies, follow
the above-
mentioned
procedure for
turning power off.
NOTE
POWER-indikator
på/av-bryter
$19&/7	4
 
 
 
 1.
 
 
						

							17
STANDBY/ONLASERBLANK
RGBVIDEO
AUTO
MENU
ENTERKEYSTONE
RESET
FREEZE ASPECT
ESC
MAGNIFY
POSITION
OFF ONVOLUME
SEARCH
MUTE
1Press the VOLUME button
As illustrated on the right, a dialog will
appear on the screen to aid you in adjusting
the volume.
1Press the MUTE button
As illustrated on the right, a dialog will appear on the
screen indicating that you have muted the sound.  Press
the VOLUME button to close the dialog.  (Even if you dont
do anything, the dialog will automatically disappear after
a few seconds.)
Press the MUTE button again to restore the sound.
2Press the , buttons to adjust
the volume
Press the VOLUME button again to close the dialog and
complete this operation.  (Even if you dont do anything, the
dialog will automatically disappear after a few seconds.)
Press this to increase the volume
Press this to decrease the volume
VOLUME
MUTE
AUTO
MENU
ENTERKEYSTONE
RESET
FREEZE ASPECT
ESC
MAGNIFY
POSITION
OFF ONVOLUME
SEARCH
MUTE
16
VOLUME
16
VOLUME
16
VOLUME
ADJUSTING THE VOLUME
TEMPORARILY MUTING THE SOUND
$19&/7	4
 
 
 
 1.
 
 
						

							18
STANDBY/ONLASERBLANK
RGBVIDEO
AUTO
MENU
ENTERKEYSTONE
RESET
FREEZE ASPECT
ESC
MAGNIFY
POSITION
OFF ONVOLUME
SEARCH
MUTE
1Press the POSITION button
As illustrated on the right, a dialog will appear on the screen
to aid you in adjusting the position.
2Use the , , , buttons to adjust
the position
When you want to initialize the position, press the RESET
button during adjustment.
Press the POSITION button again to close the dialog and
complete this operation.  (Even if you dont do anything, the
dialog will automatically disappear after a few seconds.)
This function is only available for RGB IN 1/2 input.
ADJUSTING THE POSITION
POSITION
POSITION
Control panel
$19&/7	4
 
 
 
 1.
 
 
						

							19
The automatic adjustment operation requires approximately 10 seconds. Also, please
note that it may not function correctly with some input signals.
NOTE
1
USING THE AUTOMATIC ADJUSTMENT FEATURE
Press the AUTO button
Horizontal position (H. POSIT), vertical position (V.
POSIT), clock phase (H. PHASE) and horizontal size (H.
SIZE) are automatically adjusted.
Make sure that the application window is set to its
maximum size prior to attempting to use this feature.
Dark pictures may still be incorrectly adjusted. Use a
bright screen when adjusting.
The signal type best suited for the respective input
signal is selected automatically.
This feature is available only if VIDEO is set to AUTO in
the INPUT menu.
Automatic Adjustment for RGB Input
Automatic Adjustment for Video Input
STANDBY/ONLASERBLANK
RGBVIDEO
AUTO
MENU
ENTER
KEYSTONE
RESET
FREEZE ASPECT
ESC
MAGNIFY
POSITION
OFF ONVOLUME
SEARCH
MUTE
AUTO
$19&/7	4
 
 
 
 1.
 
 
						

							20
• This function may not be work well with some types of input signals.
• The adjustable range for correcting keystone distortions will vary with the type of
input signal.
NOTE
CORRECTING KEYSTONE DISTORTIONS
1Press the KEYSTONE button
As illustrated on the right, a dialog will appear
on the screen to aid you in correcting the
distortion. 
2Use the , buttons to select the
direction of distortion to correct ( / )
3Use the,buttons to correct the
distortion
Press the KEYSTONE button again to close the dialog and
complete this operation.  (Even if you dont do anything, the
dialog will automatically disappear after a few seconds.)
STANDBY/ONLASERBLANK
RGBVIDEO
AUTO
MENU
ENTERKEYSTONE
RESET
FREEZE ASPECT
ESC
MAGNIFY
POSITION
OFF ONVOLUME
SEARCH
MUTE
KEYSTONEKEYSTONE
16
KEYSTONE
Control panel
$19&/7	4
 
 
 
 1.
 
 
						

							21
The projector will automatically exit from MAGNIFY mode if either the INPUT SELECT,
AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the input signals state.
NOTE
•The projector will automatically exit from FREEZE mode if either the POSITION, VOLUME, MUTE, AUTO,
BLANK ON/OFF or MENU ON/OFF feature is used, or, if there is a change in the input signals state.
•If the projector continues projecting the same image for a long time (i.e. you forget to exit FREEZE mode),
the image might possibly remain as an afterimage. Do not leave the projector in FREEZE mode for too long.
NOTE
USING THE MAGNIFY FEATURE
FREEZING THE SCREEN
1Press the MAGNIFY (ON) button
The projector enters MAGNIFY mode.
2Press the POSITION button, then use the,,
,
buttons to select the area to enlarge and then
press the POSITION button again to confirm your
selection
3Press the,buttons to zoom in and
out of the selected area.
Press the MAGNIFY (OFF) button to exit MAGNIFY mode
and restore the screen to normal. (The projector will also
automatically exit MAGNIFY mode if there is a change in the
input signals state.)
1Press the FREEZE button
The [II] icon appears and the screen will freeze at
the current image. Press the FREEZE button again
and the [  ] appears as the projector exits
FREEZE mode.
STANDBY/ONLASERBLANK
RGBVIDEO
AUTO
MENU
ENTERKEYSTONE
RESET
FREEZE ASPECT
ESC
MAGNIFY
POSITION
OFF ONVOLUME
SEARCH
MUTE
MAGNIFYMAGNIFYON
POSITIONPOSITION
ENTER
RESET
FREEZE ASPECT
ESC
MAGNIFY
POSITION
OFF ONVOLUME
SEARCH
MUTE
FREEZE
Û
$19&/7	4
 
 
 
 1.
 
 
						

							22
SIGNAL SEARCHING
SELECTING THE ASPECT RATIO
TEMPORARILY BLANKING THE SCREEN
1Press the SEARCH button
When you press the SEARCH button, the projector begins
searching for input signals. If it detects an input signal, the
search will cease and the projector will project the detected
signal. If the projector is unable to find an input signal at any of
its ports, it will return to the state it was in prior to the search.
1Press the ASPECT button
RGB IN 1, RGB IN 2, COMPONENT VIDEO
(HDTV signals : 1125i (1035i/1080i), 750p)
VIDEO IN, S-VIDEO IN, COMPONENT VIDEO
(Non-HDTV signals : 525i, 525p,625i)
RESET
FREEZE ASPECT
ESC
MAGNIFY
POSITION
OFF ONVOLUME
SEARCH
MUTE
SEARCHRGB IN 1 RGB IN 2 VIDEO IN
S-VIDEO IN
COMPONENT VIDEO
AUTO
MENU
ENTERKEYSTONE
RESET
FREEZE ASPECT
ESC
MAGNIFY
POSITION
OFF ONVOLUME
SEARCH
MUTE
ASPECT
4:316:9
4:3 16:9 SMALL
1STANDBY/ONLASERBLANK
RGBVIDEO
AUTO
Press the BLANK button
The input signal screen is shut off, and a blank screen
appears. You can set the blank screen using the menu
(from the SCREEN menu, select BLANK). Press the BLANK
button again to remove the blank screen, and return to the
input signal screen.
BLANK
$19&/7	4
 
 
 
 1.