Dukane Imagepro 8800a Liquid Crystal Projector Operating Guide

9
RGB  IN 12
CONTROL RGB  OUTS-VIDEO  IN
VIDEO  IN
AUDIO  IN
L
MONO
R
USB AUDIO
OUT AUDIO  IN
12
Names and functions of each part (continued)
Main power switchUsed to turn the power on and off.: OFF: ON
VIDEO IN jack
S-VIDEO IN jack
Mini DIN 4-pin connector
VIDEO IN jack
RCA jack
AUDIO L/R IN jack
RCA jack
AC IN jackUsed to connect the
accessory power cord.
RGB IN jackD-sub 15-pin shrink (1/2)
CONTROL jackD-sub 15-pin shrink
AUDIO OUT jack (RGB/VIDEO)Stereo mini jack
AUDIO IN jack (RGB)Stereo mini jack...

10
Names and functions of each part (continued)
Remote control transmitter
FOCUS buttonUsed to adjust the focus of the image on thescreen.  (Refer to page 13.)ZOOM b uttonUsed to adjust the size of the image . (Ref er topage 13.)
FREEZE b uttonUsed to tur n the freeze (still) image displa y on and off.
AUT O b uttonUsed to e xecute auto-adjust.*3
MA GNIFY b uttonUsed to magnify the displa yed image .
BLANK b uttonUsed to tur n blanking on and off .(Refer to page 20.)
*2With the P in P function, signals...

11
Names and functions of each part (continued)
Loading the batteriesLoading AA batteries into the remote control.
The laser pointer of the remote control is used in place of a fing er or rod.
Never look directly into the laser beam outlet or point the laser beam at
other people.
The laser beam can cause vision problems.
Warning
AVOID EXPOSURE-LASER RADIA TION IS EMITTED FROM THIS APER TURE
1Remove the battery
cover.
Push the knob while
lifting up the battery
cover .  
  
   
2Loading the batteries.
Mak...

12
Installation
Typical LCD Projector and Screen Installation
Using the adjusters
a. Distance from the LCD projector to the screen 
b. Distance from the lens center to the bottom ofthe screen (a,b : +/-10%).
The projection distances shown in the diagram to
the left are for full size (1024 x 768 dots.)
The LCD projector should normally be used 
level (the legs can point upward).
Positioning the projector sideways, or with the
lens pointing upward or downward can cause the
internal temperature to rise,...

13
Basic operations
To project
1Turn on the main power switch of the projector [ I: ON].
• The Power indicator lights orange.
2Press the STANDBY / ON button.
• The Power indicator will blink green and then light green.
• The green blinking indicates warmup.
• After the power is turned on, the lamp will be cooled for approximately 1 min. and the power cannot
be turned on even by pressing the STANDBY/ON button.
3Remove the lens cap.
4Use the ZOOM button to adjust the screen size.
5Use the FOCUS button to...

14
VIDEO
STANDBY/ON
RGB
POSITION LASER
MENU
RESET
MAGNIFY
FREEZE
OFFVOLUME
P in PMUTE
AUTOBLANKTIMER
Turning off the power
Plug & Play
Basic operations (continued)
1Press the STANDBY/ON button for approximately 1 sec.
• The Power indicator will blink orange, then the lamp will turn off. Approximately 1 sec. after that, the
lamp will light orange.
• After the power is turned off, the lamp will be cooled for approximately 1 min. and the power cannot
be turned off even by pressing the STANDBY/ON button.
•...

15
VIDEO
STANDBY/ON
RGB
POSITION
LASER
MENU
RESET
MA GNIFY
FREEZE
OFFVOLUME
P in PMUTE
AUT OBLANKTIMER
Freeze function
Basic operations (continued)
1Press the FREEZE button.
• The image being displayed will freeze.
•  The [     ] mark appears in the lo wer right corner of the screen when the Freeze function is on.
1Press the FREEZE button.
• The FREEZE function will be cancelled.
•  The [     ] mark will be displayed for approximately 3 sec. when the FRE\
EZE function is cancelled.
1
This function is...

16
1Press the MAGNIFY+button.
• The center part of the image will be displayed magnif ied approximately two times.
2Press the MAGNIFY +button.
• When this b utton is pressed, the image will be displayed e ven larger.
3Press the MAGNIFY –button.
• When this b utton is pressed, the image will be displayed e ven smaller.
4Press the POSITION button.
5Press the DISK PAD up,  down, left and right buttons.
• The magnif ied area will mo ve in accordance with the b utton pressed.
6Press the MAGNIFY OFF button....

VIDEO
STANDBY/ON
RGB
POSITION
LASER
MENURESET
MA GNIFY
FREEZE
OFFVOLUME
P in PMUTE
AUT OBLANKTIMER
FOCUSZOOM
MENU
17
Adjustments and functions
1Press the MENU (             ) buttons of the projector or the
MENU button of the remote control.
• The Menu screen will appear. (refer to page 18 - 21 for details.)
2of the projector or the 
button of the remote control to select the menu item to be 
•  The selected menu item will be displayed in orange.
3
1,3
1,2,3
1
2,3
3
Returning to the initial settings
•...

18
Adjustments and functions (continued)
RGB signal inputVideo signal input
VOLUMEBRIGHTCONTRASTV  POSITH  POSITH  PHASEH  SIZECOLOR BAL  RCOLOR BAL  B
100100
800
SETUPINPUTOPT .IMAGE
VOLUMEBRIGHTCONTRASTSHARPNESSCOLORTINTCOLOR  BAL  RCOLOR  BAL  B
SETUPINPUTOPT .IMAGE
•The menu cannot be displayed while the initial screen (“ No input is detected. ” or “Sync is
out of range. ”) is being displayed.
• Tint cannot be adjusted with PAL or SECAM video signal input.
•  Tint, color and sharpness cannot be...