Dukane Imagepro 8784 Projector Users Manual

							
4

ItemDescription
SERVICE(continued)
AUTO ADJUSTUsing the ▲/▼ buttons enables/disables the automatic adjustment. When DISABLE is selected, the automatic adjustment feature is disabled, although rough adjustment is automatically performed depending on the basic setting.
FINE ó FAST ó DISABLE      
FINE: Finer tuning including H.SIZE adjustment.
FAST: 
 Faster tuning, setting H.SIZE to prearranged data for the 
input signal.
• Depending on conditions, such as input image, signal cable to the projector, environment around the projector, etc., the automatic adjustment may not work correctly.  In such a case, please choose DISABLE to disable the automatic adjustment, and make adjustment manually.
GHOST
1.  Select a color element of ghost using the ◄/► 
buttons. 
2. 
 Adjust the selected element using the ▲/▼ buttons to disappear ghost.
FILTER MESSAGEUse the ▲/▼ button to set the timer for the interval to show the message for cleaning up the air filter. 
50h ó 100h ó 200h ó 300h ó TURN OFF
After selecting “50h”, “100h”, “200h”, or “300h”, the message “REMINDER *** HRS PASSED AFTER THE LAST FILTER CHECK” will appear after the timer reaches the interval time set by the menu (60). When the “TURN OFF” is chosen, the air filter cleaning message will not appear.
• Please check and clean the air filter periodically, even if there is no message. If the air filter becomes to be blocked by dust or others, the internal temperature will rise, which could cause malfunction, or reduce the lifetime of the projector.• It is recommended to choose “100h” in general. Please be careful with the operating environment of the projector and the condition of the air filter, especially when the “200h”, “300h” or “TURN OFF” is chosen. 
OPTION Menu (continued)
OPTION Menu
#761#&,756(+0
&+5#$.(#56



)*156
4 )$
(+.64/55#)
JJ
JJ67401((
(continued on next page) 
						

							
4

ItemDescription
SERVICE(continued)
KEY LOCKUsing  the  ▲/▼  buttons  turns  on/off  the  key  lock  feature.  When TURN  ON  is  selected,  the  buttons  on  the  projector  except  the STANDBY/ON button are locked.TURN ON ó TURN OFF• Please use to avoid a mischief and touching accidentally. This function does not have any effect on the remote control.
REMOTE FREQ.Use the ▲/▼ button to change the Projector's remote sensor setting.
1:NORMAL ó 2:HIGH
Items with a checkmark are on. The factory default setting is for both 1:NORMAL and 2:HIGH to be on.  If the remote control does not function correctly set this to either only 1 or only 2 (13).Neither can be turned off at the same time.
INFORMATIONSelecting this item displays a dialog titled “INPUT INFORMATION”. It shows the information about the current input.
INPUT-INFORMATIONCOMPUTER1024x768 @60FRAME LOCK
INPUT-INFORMATIONS-VIDEOPALAUTO
INPUT-INFORMATIONCOMPUTER576i @50
• The “FRAME LOCK” message on the dialog means the frame lock function is working. 
• This item can't be selected for no signal and sync out.
FACTORY RESETSelecting RESET using the button ▲ performs this function. By this function, all the items in all of menus will collectively return to the initial setting. Note that the items LAMP TIME, FILTER TIME, LANGUAGE, MIU and SECURITY are not reset.
RESET  CANCEL
OPTION Menu (continued)
OPTION Menu
(continued on next page)
4/16(43
014/#.*+)*
064:œ:¥:«:œ:© 
						

							
43

ItemDescription
SECURITY
This projector is equipped with security functions.User registration is required before using the security functions.Please contact your local dealer.
1. Using Security Features
1.1 Inputting the PASSWORD
1.1-1  Use the ▲/▼ buttons on the OPTION menu to select SECURITY and press the ► button. The ENTER PASSWORD box will be displayed.The factory default PASSWORD is 2805. This PASSWORD can be changed (1.2 Changing the PASSWORD). • It is strongly recommended the factory default PASSWORD to be changed as soon as possible.
1.1-2 
 Use the ▲/▼/◄/► buttons to enter the 
registered PASSWORD. Move the cursor to the right side of the ENTER PASSWORD BOX and press the ► button to display the SECURITY menu.  If an incorrect PASSWORD is input the ENTER PASSWORD BOX will be displayed again. If incorrect PASSWORD is input 3 times the projector will turn off. Afterwards the projector will turn off every time an incorrect PASSWORD is input.
1.2 Changing the PASSWORD
1.2-1  Use the ▲/▼ buttons on the SECURITY menu to select SECURITY PASSWORD CHANGE and press the ► button to display the ENTER NEW PASSWORD BOX.
1.2-2 
 
Use the ▲/▼/◄/► buttons to enter the new 
PASSWORD.
1.2-3 
 
Move the cursor to the right side of the 
ENTER NEW PASSWORD BOX and press the ► button to display the NEW PASSWORD AGAIN BOX, enter the same PASSWORD again. 
1.2-4 
 
Move the cursor to the right side of the NEW 
PASSWORD AGAIN BOX and press the ► button and the NOTE NEW PASSWORD BOX will be displayed for about 20 seconds, please make note of the PASSWORD during this time.  Pressing the ENTER button will close the NOTE NEW PASSWORD BOX.• Please do not forget your PASSWORD.
OPTION Menu (continued)
OPTION Menu
5%74+6;0642#55914&
0:6

37+6
5%74+6;
5%74+6;2#55914&%*#0)/[5ETGGP2#55914&67401((2+0.1%-67401((64#05+6+10&6%61467401((
5%74+6;064092#55914&
0:6

37+6
5%74+6;092#55914&#)#+0
1-

%#0%.
5%74+6;016092#55914&
:+6

064
(continued on next page) 
						

							
44

ItemDescription
SECURITY(continued)
1.3 If you have forgotten your PASSWORD
1.3-1  Follow the procedure in 1.1-1 to display the ENTER PASSWORD BOX.
1.3-2 
 
While the ENTER PASSWORD BOX is 
displayed, press and hold the RESET button for about 3 seconds or press and hold the INPUT and ► buttons on the projector for about 3 secondsThe 10-digit Inquiring Code will be displayed. • If there is no key input for about 55 seconds while the Inquiring Code is displayed the menu will close. If necessary repeat the process from 1.3-1.
1.3-3   Contact your dealer with the 10-digit Inquiring Code. Your PASSWORD 
will be sent after your user registration information is confirmed.
2. Using the MyScreen PASSWORD Function
The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten.
2.1 Turning on the MyScreen PASSWORD 
Function
2.1-1  Use the ▲/▼ buttons on the SECURITY menu to select MyScreen PASSWORD and press the ► button to display the MyScreen PASSWORD on/off menu.
2.2 Setting the PASSWORD
2.2-1  Display the MyScreen on/off menu using the procedure in 2.1-1.
2.2-2 
 
Use the ▲/▼ buttons on the MyScreen 
PASSWORD on/off menu to select TURN ON.The ENTER PASSWORD BOX (small) will be displayed.
2.2-3   Use the ▲/▼/◄/► buttons to enter the 
PASSWORD.  Move the cursor to the right side of the ENTER PASSWORD BOX (small) and press the ► button to display the CHECK PASSWORD BOX, enter the same PASSWORD again.
5%74+6;2#55914&

+PSWKTKPI%QFG
OPTION Menu (continued)
OPTION Menu
/[5ETGGP0642#55914&
0:6

37+6
/[5ETGGP%*%-2#55914&
0:6

37+6
/[5ETGGP2#55914&
67401067401((
(continued on next page) 
						

							
45

ItemDescription
SECURITY(continued)
2.2-4  Move the cursor to the right side of the CHECK PASSWORD BOX and press the ► button to display the PASSWORD for about 20 seconds, please make note of the PASSWORD during this time. Pressing the ENTER button will return to MyScreen PASS WORD on/off menu.When a PASSWORD is set for MyScreen:
• The MyScreen registration function (and menu) will be unavailable.
• The MyScreen Lock function (and menu) will be unavailable.
• The START UP setting will be locked on MyScreen (and the menu will be unavailable).Turning the MyScreen PASSWORD off will allow normal operation of both  functions.
• Please do not forget your MyScreen PASSWORD.
2.3 Turning the PASSWORD off
2.3-1  Follow the procedure in 2.1-1 to display the MyScreen PASSWORD on/off menu.
2.3-2 
 
Select TURN OFF to display the ENTER PASSWORD BOX (large). 
Enter the registered PASSWORD and the screen will return to the MyScreen on/off menu.If an incorrect PASSWORD is input the menu will close. If necessary repeat the process from 2.3-1.
2.4 If you have forgotten your PASSWORD
2.4-1   Follow the procedure in 2.1-1 to display the MyScreen PASSWORD on/off menu.
2.4-2 
 
Select TURN OFF to display the ENTER 
PASSWORD BOX (large). The 10-digit Inquiring Code will be displayed inside the BOX.
2.4-3 
 
Contact your dealer with the 10-digit Inquiring 
Code. Your PASSWORD will be sent after your user registration information is confirmed.
3. Using the PIN LOCK FunctionPIN LOCK is a function which prevents the projector from being used unless a registered Code is input.3.1 Registering the PIN Code
3.1-1   Use the ▲/▼ buttons on the SECURITY menu to select PIN LOCK and press the ► button or the ENTER button to display the PIN LOCK on/off menu.
0:637+6
+PSWKTKPI%QFG         
/[5ETGGP0642#55914&
OPTION Menu (continued)
OPTION Menu
/[5ETGGP%1/2.6
064:+6
2+0.1%-
67401067401((
(continued on next page) 
						

							
46

ItemDescription
SECURITY(continued)
3.1-2  Use the ▲/▼ buttons on the PIN LOCK on/off menu to select TURN ON and the PIN BOX will be displayed. 
3.1-3 
 
  Input a 4 part PIN Code using the ▲, ▼, 
◄, ►, COMPUTER/STORAGE and INPUT buttons.A CONFIRMATION BOX will appear. Reenter the same PIN Code. This will complete the PIN Code registration.• If there is no key input for about 55 seconds while the PIN BOX or the CONFIRMATION BOX are displayed the menu will close. If necessary repeat the process from 3.1-1.Afterwards, anytime the projector is restarted after AC power is turned off the PIN BOX will be displayed. Enter the registered PIN Code.The projector can be used after entering the registered PIN Code. If an incorrect PIN Code is input the PIN BOX will be displayed again.If an incorrect PIN Code is input 3 times the projector will turn off. Afterwards the projector will turn off every time an incorrect PIN Code is input. The projector will also turn off if there is no key input for about 5 minutes while the PIN BOX is displayed.This function will activate only when the projector is started after  AC power is turned off.
• Please do not forget your PIN Code.
3.2 Turning Off the PIN LOCK Function
3.2-1  Follow the procedure in 3.1-1 to display the PIN LOCK on/off menu. Use the ▲/▼ buttons to select TURN OFF and the PIN BOX will be displayed.Enter the registered PIN Code to turn the PIN LOCK function off.If an incorrect PASSWORD is entered the menu will close.
3.3 If you have forgotten your PIN Code
3.3-1  While the PIN BOX is displayed, press and hold the RESET button for 3 seconds or press and hold the INPUT and ► buttons for 3 seconds. The 10-digit Inquiring Code will be displayed.• If it passes for about 5 minutes after the PIN BOX is displayed the projector will turn off.
3.3-2 
 Contact your dealer with the 10-digit Inquiring Code. Your PASSWORD 
will be sent after your user registration information is confirmed.
OPTION Menu (continued)
OPTION Menu
2+0$1:
%1/2764
+PRWV2+0%QFG
2+0$1:

%QPHKTOCVKQP%1/2764
2+0$1:

+PSWKTKPI%QFG
(continued on next page) 
						

							
47

ItemDescription
SECURITY(continued)
4. Using the Transition Detector Function
While the Transition Detector function is ON, when power switch is started to supply to the projector, it might react as below.• Transition Detector alarm shown below might appear on screen, if the projector has been moved or re-installed.• Transition Detector alarm might appear on screen, if the MIRROR setting has been changed.• Keystone adjustment feature has been prohibited as long as the Transition Detector function is ON.
4.1 Turning On the Transition Detector Function
4.1-1  Use the ▲/▼ buttons on the SECURITY menu to select TRANSITION DETECTOR and press the ► or the ENTER button to display the TRANSITION DETECTOR on/off menu. Select TURN ON and the current angle and mirror setting will be recorded.• This feature may not function properly if the projector is not in a stable position when TURN ON is selected.
4.1-2  If this function is set to TURN ON when the vertical angle of the projector or mirror setting at which the projector is turned on is different than the previously recorded the Transition Detector Alarm will be displayed and the projector will not display the input signal.
Set the Transition Detector off in the SECURITY menu to display the input signal.
If the Transition Detector ALARM is displayed for about 5 minutes the lamp will turn off. This function will activate only when the projector is started after turning off the AC power.
4.2 Setting the Transition Detector PASSWORD
4.2-1  Use the ▲/▼ buttons on the SECURITY menu to select TRANSITION DETECTOR and press the ► or the ENTER button to display the TRANSITION DETECTOR on/off menu.
4.2-2 
 
Use the ▲/▼ buttons on the TRANSITION 
DETECTOR on/off menu to select TURN ON. The ENTER PASSWORD BOX (small) will be displayed.
4.2-3  Use the ▲/▼/◄/► buttons to enter a PASSWORD. Move the cursor to the right side of the ENTER PASSWORD BOX (small) and press the ► button to display the CHECK PASSWORD BOX, enter the same PASSWORD again.
4.2-4   Move the cursor to the right side of the CHECK PASSWORD BOX and press the ► button to display the PASSWORD for about 20 seconds, please make note of the PASSWORD during this time.Pressing the ENTER button will return to the TRANSITION DETECTOR on/off menu.• Please do not forget your Transition Detector PASSWORD.
OPTION Menu (continued)
OPTION Menu
64#05+6+10&6%614
67401067401((
2+0$1:
64#05+6+10&6%61410  6JGRTQLGEVQTJCUDGGPVTCPUHGTTGFHTQORTGXKQWUN[KPUVCNNGFRQUKVKQP+H[QWYKUJVQJCXGCUSWCTGKOCIGQPUETGGPCICKPFKUCDNG6TCPUKVKQP&GVGEVQTQP/GPW
64#05+6+10&6%6140642#55914&
0:6

37+6
64#05+6+10&6%614%*%-2#55914&
0:6

37+6
64#05+6+10&6%614%1/2.6
:+6

064
(continued on next page) 
						

							
48

ItemDescription
SECURITY(continued)
4.3 Setting the Transition Detector off
4.3-1  Follow the procedure in 4.1-1 to display the TRANSITION DETECTOR on/off menu.
4.3-2 
 
Select TURN OFF to display the ENTER PASSWORD BOX (large). 
Enter the registered PASSWORD and the screen will return to the TRANSITION DETECTOR on/off menu. If an incorrect PASSWORD is input the menu will close. If necessary repeat the process from 4.3-1.
4.4 If you have forgotten your PASSWORD
4.4-1   Follow the procedure in 4.1-1 to display the TRANSITION DETECTOR on/off menu.
4.4-2 
 
Select TURN OFF to display the ENTER 
PASSWORD BOX (large). The 10-digit Inquiring Code will be displayed inside the BOX.
4.4-3   Contact your dealer with the 10-digit Inquiring Code. Your PASSWORD will be sent after your user registration information is confirmed.
OPTION Menu (continued)
OPTION Menu
0:637+6
+PSWKTKPI%QFG         
64#05+6+10&6%6140642#55914& 
						

							
49

(continued on next page)
ItemDescription
LIVE MODE
Selecting this item sets the projector onto the “Live Mode”. On the “Live Mode”, the projector displays the images from the PC via Network, supported by “MIU Live Viewer”. ( 1.1 Live Mode of the User’s Manual - Network Functions)In the Live Mode, the message “Waiting for connection” will be displayed until the “MIU Live Viewer” start to send computer screen image.
PC-LESSPRESENTATION
Selecting this item displays the PC-LESS PRESENTATION menu.Using the menu is able to make the projector display the images stored in SD Memory Card or USB memory, and realizes a presentation without 
PC. ( 1.2 PC-LESS Presentation of the User’s Manual - Network Functions)
MIU Menu
/07=%1/2764?
2+%674
5.%6

+/#)
5672+0276
126+10/+7#5;/07
5%40
.+8/1&2%.5524506#6+105672G5*16+0(14/#6+10548+%
MIU Menu
Remember that incorrect network settings on this projector 
may cause trouble on the network. Be sure to consult with 
your network administrator before connecting to an existing 
access point on your network.
Select “MIU” from the main menu to access the following 
functions. 
Select an item using the ▲/▼ cursor buttons on the 
projector or remote control, and press the ► cursor button 
on the projector or remote control, or ENTER button on 
the remote control to execute the item. Then perform it 
according to the following table.
See the User’s Manual - Network Functions for details of 
MIU operation.
NOTE  • The factory default setting for DHCP is OFF. If your network has 
DHCP enabled, and needs to set IP ADDRESS, SUBNET MASK and DEFAULT 
GATEWAY automatically, please set DHCP to ON. ( 2.5.2 Network Settings 
of the User’s Manual - Network Functions)
• If you are not utilizing SNTP ( 2.5.7 Date/Time Settings of the User’s 
Manual - Network Functions), then you must set the DATE AND TIME (51) 
during the initial installation.
2%.5524506#6+106*7/$0#+.5.+&5*19&+4%64;&+52.#;5+
						

							
50

(continued on next page)
ItemDescription
SETUP
Selecting this item displays the MIU SETUP menu.
Use the ▲/▼ buttons to select an item, and the ► or ENTER button on the remote control to perform the item.
DHCP (Dynamic Host Configuration Protocol)
Use the ▲/▼ buttons to turn DHCP on/off.
ON ó OFF
Select OFF when the network does  not have DHCP enabled.
• When the “DHCP” setting changes to “ON”, it takes a little time to obtain IP address from DHCP server.• Auto IP function will be assigned an IP address if the projector could not obtain an IP address from server even if DHCP is “ON”.
IP ADDRESS
Use the ▲/▼/◄/► buttons to enter the IP ADDRESS. This function can only be used when DHCP is set to OFF.
• The IP ADDRESS is the number that identifies this projector on the network. You cannot have two devices with the same IP ADDRESS on the same network.• The IP ADDRESS “0.0.0.0” is prohibited.
SUBNET MASK
Use the ▲/▼/◄/► buttons to enter the same SUBNET MASK used by your PC. This function can only be used when DHCP is set to OFF.
• The SUBNET MASK ”0.0.0.0” is prohibited.
DEFAULT GATEWAY
Use the ▲/▼/◄/► buttons to enter the DEFAULT GATEWAY (a node on a computer network that serves as an access point to another network) address.This function can only be used when DHCP is set to OFF.
&*%2101((
 /+75672&*%210+2#&&45557$06/#5-&(#7.6)#69#;
#0&6+/6+/&+((40%
/1&%*
06914-/1&52&0%4;26+10
MIU Menu
MIU Menu (continued)

+2#&&455

255.255.0
SUBNET MASK
255.
0.0.0
DEFAULT GATEWAY
0.