Dukane Imagepro 8781 Portable Lcd Projector Users Manual

0

Turning off  the power
. Press the STANDBY/ON button on the projector 
or the remote control.
The message "Power off?" will appear on the 
screen for about 5 seconds.
2. Press the STANDBY/ON button again while the 
message appears. 
The projector lamp will go off, and the POWER 
indicator will begin blinking in orange. Then the 
POWER indicator will stop blinking and light in 
steady orange when the lamp cooling is complete.
3. Make sure that the POWER indicator lights in 
steady...


ENGLISH

Replacing the lamp
A lamp has finite product life. Using the lamp for long periods of time could cause 
the pictures darker or the color tone poor. Note that each lamp has a different 
lifetime, and some may burst or burn out soon after you start using them. 
Preparation of a new lamp and early replacement are recommended. To prepare 
a new lamp, contact to your dealer and tell the lamp type number.

Type number : 456-8755G
. Turn the projector off, and unplug the power cord....

2

 HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE
WARNING  ►The projector uses a high-pressure mercury glass lamp. The 
lamp can break with a loud bang, or burn out, if jolted or scratched, handled 
while hot, or worn over time. Note that each lamp has a different lifetime, and 
some may burst or burn out soon after you start using them. In addition, when 
the bulb bursts, it is possible for shards of glass to fly into the lamp housing, 
and for gas containing mercury to escape from the projector’s...

3
ENGLISH

Please check and clean the air filter periodically. When the indicators or a 
message prompts you to clean the air filter, comply with it as soon as possible. 
Replace the air filter when it is damaged or too soiled. To prepare a new air filter, 
contact to your dealer and tell the air filter type number.
Type number : MU04951
When you replace the lamp, please replace the air filter. An air filter of specified 
type will come together with a replacement lamp for this projector .
....

4

. Turn the projector off, and unplug the power cord. Allow the projector to cool sufficiently.
2. After making sure that the projector has cooled adequately, pull the SD card slot cover forward, pushing slightly its edge up, and remove it from the projector.
3. Remove the battery case. Hold the battery case gutter by finger nail or other thing and pull out the battery case slowly from the battery slot. While the projector is installed upside down, such as a ceiling mount, please remember...

5
ENGLISH

Using the CD manual
The other manuals for this product are written into the included CD-ROM titled 
“User’s Manual (detailed)”. Before using the CD-ROM, please read the following 
to ensure the proper use. 
 System requirements
The system for using the CD-ROM requires the following. 
  Windows®:   OS:Microsoft® Windows® 98, 98SE, NT4.0, Me, 2000/XP, or 
later
  CPU:Pentium® processor 133MHz / Memory:32MB or more
  Macintosh®: OS:Mac OS 10.2 or later
  CPU:Power PC® / Memory:32MB or more...

6

Regulator y notices
Declaration of Conformity
Trade name   HITACHI
Model Number  CP-X308
Responsible Party  Hitachi America, Ltd.
Address  900 Hitachi way, Chula Vista, A 91914-3556  U.S.A.
Telephone Number  +1 -800-225-1741
This device complies with part 15 of the FCC Rules. Operation is subject to the following 
two conditions: (1) This device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired...

7
ENGLISH

Information for users applicable in European Union countries
1. The manufacturer (Gemtek) hereby declare that this equipment (wireless network card), model SD-Link11g is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
2. This symbol on the product or on its packaging means that your electrical and electronic equipment should be disposed at the end of life separately from your household wastes. There are separate collection systems for...

8

Specifications
ItemSpecifications
Product nameLiquid crystal projector
Liquid Crystal Panel
Panel size1.6 cm (0.63 type)
Drive systemTFT active matrix
Pixels786,432 pixels (1024 horizontal x 768 vertical)
LensZoom lens   F=1.7 ~ 1.9   f = 19.5~ 23.4 mm   (approximately)
Lamp220W UHB
Audio output7 W
Power supplyAC 100-120V/3.8A, AC220-240V/1.6A
Power consumption350W
Temperature range5 ~ 35°C (Operating)
Size340 (W) x 117 (H) x 270 (D) mm   *Excluding protrusionsPlease refer to the following...

19
HSILGNE
Warranty and after-service
If an abnormal operation (such as smoke, strange odor or excessive sound) should occur, 
stop using the projector immediately . Otherwise if a problem occurs with the projector, 
first refer to the “T roubleshooting” of the “Operating Guide” in the CD  and run through the 
suggested checks. 
If this does not resolve the problem, please contact to your dealer or service compan
y.  They 
will tell you what warranty condition is applied.
Please check the following web...