Dukane Imagepro 8767a Portable Lcd Projector Users Manual

							13
This section describes how to set up your projector and how to connect video and audio sources.
2. Installation and Connections

 Setting Up the Screen and the Projector
Selecting a Location 
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is
approximately 21" (0.53 m) measured diagonally when the projector is roughly 29 inches (0.73 m) from the wall or
screen. The largest the image can be is 300" (7.6 m) when the projector is about 393 inches (10 m) from the wall or
screen. Use the drawing below as a guide.Your projector is simple to set up and use.
But before you get started, you must first:
zSet up a screen and the projector.
xConnect your computer or video equip-
ment to the projector. See pages 
17 to
21.
cConnect the supplied power cable. See
page
22.
NOTE: Ensure that the power cable and any
other cables are disconnected before moving
the projector. When moving the projector or
when it is not in use, cover the lens with the
lens cap.To the wall outlet.
300"
240
"
200"180"
150"
120"
100"
60"
40"30"21"
80"
Distance (Unit: m/inch)
Screen Size (Unit: cm/inch
Screen Size
Lens center
609.6(W)
457.2(H) / 240(W)
180(H)
487.7(W)
365.8(H) / 192(W)
144(H)
406.4(W)
304.8(H) / 160(W)
120(H)
365.8(W)
274.3(H) / 144(W)
108(H)
304.8(W)
228.6(H) / 120(W)
90(H)
243.8(W)
182.9(H) / 96(W)
72(H)
203.2(W)
152.4(H) / 80(W)
60(H)
162.6(W)
121.9(H) / 64(W)
48(H)
121.9(W)
91.4(H) / 48(W)
36(H)
81.3(W)
61.0(H) / 32(W)
24(H)
61.0(W)
45.7(H) / 24(W)
18(H)
42.7(W)
32(H) / 17(W)
13(H)
1.0/380.7/
29
2.0/782.6/1043.3/1304.0/1575.0/1966.0/2366.6/2628.0/314
10.0/393
ACIN1.3/
51
32
1 
						

							14
2. Installation and Connections 
						

							15
2. Installation and Connections
Lens Center
Throw Angle (
)
Throw Distance (C) Screen center Screen Diagonal Screen Width
Screen Height
Screen Bottom
(B)
(D)
A
C
I
N
Throw Distance and Screen Size
The following shows the proper relative positions of the projector and screen. Refer to the table to determine the
position of installation.
Distance Chart
B = Vertical distance between lens center and
screen center
C = Throw distance
D = Vertical distance between lens center and
bottom of screen (top of screen for ceiling
application)
α = Throw angle
NOTE: Distances may vary +/-5%.
α
Wide – Tele
degree
–– – 9.9
12.0 – 9.8
11.9 – 9.8
11.7 – 9.7
11.6 – 9.6
11.6 – 9.6
11.6 – 9.6
11.6 – 9.6
11.5 – 9.6
11.5 – 9.6
11.5 – 9.5
11.5 – 9.5
11.5 – 9.5
11.5 – 9.5
11.5 – 9.5
11.5 – 9.5
11.4 – 9.5
11.4 – 9.5 inch
13
15
18
24
36
43
48
50
54
60
72
90
108
120
126
144
162
180 Screen Size B C
Wide – TeleDDiagonal Width Heightinch
–– – 29
28 – 34
34 – 42
46 – 56
70 – 85
84 – 102
93 – 113
98 – 119
105 – 128
117 – 142
141 – 171
176 – 214
212 – 257
236 – 285
247 – 300
283 – 343
319 – 386
354 – 429inch
-1
-2
-2
-2
-4
-4
-5
-5
-6
-6
-7
-9
-11
-12
-13
-15
-17
-18 inch
5
6
7
10
14
17
19
20
22
24
29
36
43
48
50
57
65
72 inch
21
25
30
40
60
72
80
84
90
100
120
150
180
200
210
240
270
300inch
17
20
24
32
48
58
64
67
72
80
96
120
144
160
168
192
216
240α
Wide – Teledegree
–– – 9.9
12.0 – 9.8
11.9 – 9.8
11.7 – 9.7
11.6 – 9.6
11.6 – 9.6
11.6 – 9.6
11.6 – 9.6
11.5 – 9.6
11.5 – 9.6
11.5 – 9.5
11.5 – 9.5
11.5 – 9.5
11.5 – 9.5
11.5 – 9.5
11.5 – 9.5
11.4 – 9.5
11.4 – 9.5 mm
320
381
457
610
914
1097
1219
1280
1372
1524
1829
2286
2743
3048
3200
3658
4115
4572 Screen Size B C
Wide – TeleDDiagonal Width Heightmm
––– – 730
720 – 870
870 – 1060
1170 – 1420
1770 – 2150
2130 – 2590
2370 – 2880
2490 – 3020
2670 – 3240
2970 – 3600
3580 – 4330
4480 – 5420
5380 – 6520
5980 – 7240
6280 – 7610
7190 – 8700
8090 – 9790
8990 – 10880mm
-30
-40
-50
-60
-90
-110
-120
-130
-140
-160
-190
-230
-280
-310
-330
-370
-420
-470 mm
130
150
180
240
360
440
490
510
550
610
730
910
1090
1210
1270
1460
1640
1820 mm
533
635
762
1016
1524
1829
2032
2134
2286
2540
3048
3810
4572
5080
5334
6096
6858
7620mm
427
508
610
813
1219
1463
1626
1707
1829
2032
2438
3048
3658
4064
4267
4877
5486
6096 
						

							16
2. Installation and Connections
WARNING
* Installing your projector on the ceiling must be done
by a qualified technician. Contact yourAV dealer for
more information.
* Do not attempt to install the projector yourself.
• Only use your projector on a solid, level surface. If the
projector falls to the ground, you can be injured and
the projector severely damaged.
• Do not use the projector where temperatures vary
greatly. The projector must be used at temperatures
between 41˚F (5˚C) and 95˚F (35˚C).
• Do not expose the projector to moisture, dust, or
smoke. This will harm the screen image.• Ensure that you have adequate ventilation around your
projector so heat can dissipate. Do not cover the vents
on the side or the front of the projector.
Reflecting the Image
Using a mirror to reflect your projector's image enables
you to enjoy a much larger image. Contact your
dealer if you need a mirror system. If you're using a mir-
ror system and your image is inverted, use the MENU
and SELECT buttons on your projector cabinet or your
remote control to correct the orientation. See page 
44. 
						

							17
2. Installation and Connections
 Making Connections
NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the
power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook PC is turned on after
connecting with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power
management software.
AC IN
AUDIO OUTMONITOR  OUTPC CONTROLAUDIOS-VIDEO INCOMPUTER 2 IN
VIDEO INCOMPUTER 1 IN
AUDIOL/MONOR
AUDIOL/MONOR
COMPUTER 1 IN
AUDIO
COMPUTER 2 IN
PHONE
PHONE
Connecting Your PC or Macintosh Computer
RGB signal cable (supplied)To mini D-Sub 15-pin connector on the projector. It
is recommended that you use a commercially
available distribution amplifier if connecting a
signal cable longer than the supplied one.Audio cable
(not supplied)
IBM PC or Compatibles (Desktop type)
or Macintosh (Desktop type)
NOTE: For older Macintosh, use a
commercially available pin adapter
(not supplied) to connect to your
Mac's video port.
IBM VGA or Compatibles (Notebook
type) or Macintosh (Notebook type)
Connecting your PC or Macintosh computer to your projector will enable you to project your computer's screen image
for an impressive presentation.
To connect to a PC or Macintosh, simply:
1. Turn off the power to your projector and computer.
2. Use the supplied signal cable to connect your PC or Macintosh to the projector.
3. Connect the supplied power cable. See page 
22.
4. Turn on the projector and the computer.
5. If the projector goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer
you've connected to the projector.
NOTE: The COMPUTER 1 connector supports Plug & Play (DDC2).
Enabling the computer’s external display
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector.
When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come on
or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through
external display selections. 
						

							18
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back via a commercially available scan
converter.
This is because the projector will process a video signal as a computer signal at the default setting. In that case, do the following.
* When an image is displayed with the lower and upper black portion of the screen or a dark image is not displayed correctly:
Project an image to fill the screen and then press the AUTO ADJ button on the remote control or the AUTO ADJUST button on
the projector cabinet.
2. Installation and Connections
AC IN
AUDIO OUTMONITOR  OUTPC CONTROLAUDIOS-VIDEO INCOMPUTER 2 IN
VIDEO INCOMPUTER 1 IN
AUDIOL/MONOR
AUDIOL/MONOR
COMPUTER 1 IN
Before connections: An exclusive SCART adapter (ADP-SC1) and a commercially available SCART cable are re-
quired for this connection.
NOTE: Audio signal is not available for this connection.
1. Turn off the power to the projector and your video equipment.
2. Use the ADP-SC1 SCART adapter and a commercially available SCART cable to connect the RGB input of
your projector and a SCART output (RGB) of your video equipment.
3. Connect the supplied power cable. See page 
22.
4. Turn on the power to the projector and your video equipment.
5. Use the COMPUTER 1 button on the remote control to select the COMPUTER 1 input.
Use the COMPUTER button on the remote control to select the COMPUTER input on VT47.
6. Press the MENU button on the remote control to display the menu.
7. From the menu, select [Advanced] → [Signal Select] → [Computer 1 ([Computer] on VT47)] → [Scart].
SCART is a standard European audio-visual connector for TVs, VCRs and DVD players. It is also referred to as
Euro-connector.
NOTE: The ADP-SC1 SCART adapter is obtainable from your dealer in Europe. Contact your dealer in Europe for more
information.
To connect SCART output (RGB) (Europe Operation)
Video equipment such as DVD player
Commercially available SCART cable
Female
ADP-SC1
Projector
To COMPUTER 1 input
(COMPUTER input on VT47) 
						

							19
2. Installation and Connections
Connecting an External Monitor
MONITOR OUTAUDIO
AC IN
AUDIO OUTMONITOR  OUTPC CONTROLAUDIOS-VIDEO INCOMPUTER 2 IN
VIDEO INCOMPUTER 1 IN
AUDIOL/MONOR
AUDIOL/MONOR
MONITOR OUT 
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the RGB analog
image you're projecting.
To do so:
1. Turn off the power to your projector, monitor and computer.
2. Use a 15-pin cable to connect your monitor to the MONITOR OUT (Mini D-Sub 15 pin) connector on your projector.
3. Connect the supplied power cable. See page 
22.
4. Turn on the projector, monitor and the computer.
NOTE: Daisy chain connection is not possible.
RGB signal cable (supplied)
RGB signal cable (not supplied) 
						

							20
AUDIO INLRAUDIO OUT
LR
Component
YCbCr
AC IN
AUDIO OUTMONITOR  OUTPC CONTROLAUDIOS-VIDEO INCOMPUTER 2 IN
VIDEO INCOMPUTER 1 INAUDIOL/MONOR
AUDIOL/MONOR
COMPUTER 1 INAUDIO
2. Installation and Connections
NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video output requirements.
Connecting Your DVD Player with Component Output
DVD playerAudio Equipment
Audio cable (not supplied)
Optional 15p - to - RCA (female)
3
cable (ADP-CV1)
Component video RCA
3
cable (not supplied)
You can connect your projector to a DVD player with component output or Video output. To do so, simply:
1. Turn off the power to your projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr) output, use a commercially available component video cable
(RCA
3) and the optional 15-pin-to-RCA (female)
3 cable to connect your DVD player to the COMPUTER IN
connector on the projector.
For a DVD player without component video (Y,Cb,Cr) output, use common RCA cables (not provided) to connect a
composite VIDEO output of the DVD player to the Video Input of the projector.
3. Connect the supplied power cable. See page 
22.
4. Turn on the projector and DVD player.
A component signal will be automatically displayed. If not, from the menu, select [Advanced]→ [Signal Select]→
[Computer], and then place a check mark in the Component radio button. 
						

							21
2. Installation and Connections
AUDIO INLRAUDIO OUTLRVIDEO OUTS-VIDEO VIDEO
AC IN
AUDIO OUTMONITOR  OUTPC CONTROLAUDIOS-VIDEO INCOMPUTER 2 IN
VIDEO INCOMPUTER 1 IN
AUDIOL/MONOR
AUDIOL/MONOR
S-VIDEO IN
VIDEO IN
AUDIO
AUDIO
Connecting Your VCR or Laser Disc Player
S-Video cable (not supplied)
Video cable (not supplied)
VCR/ Laser disc player
Audio equipment
Audio cable (not supplied)
Use an RCA or S-Video cable (not provided) to connect the video and use RCA cables (not provided) to connect
the audio from your VCR, laser disc player or document camera to your projector.
To make these connections, simply:
1. Turn off the power to the projector and VCR, laser disc player or document camera.
2. Connect one end of an RCA cable to the video output (or one end of an S-Video cable to the S-Video output
connector) on the back of your VCR or laser disc player, connect the other end to the appropriate video input
on your projector. Connect one end of a pair RCA cables (not supplied) to the audio output on the back of your
VCR or laser disc player, connect the other end to your audio equipment or to the appropriate audio input on
the projector.
Be careful to keep the right and left channel connections correct for stereo sound.
3. Connect the supplied power cable. See page 
22.
4. Turn on the projector and the VCR or laser disc player.
NOTE: Refer to your VCR or laser disc player owner's manual for more information about your equipment's video output
requirements.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back in fast-forward or fast-rewind via
a scan converter. 
						

							22
2. Installation and Connections
A
C IN
ZOOMFO
CU
S
SELECTL
A
M
P
STA
T
U
S
P
O
W
E
R
V
ID
E
O
S
-V
ID
E
OC
O
M
P
U
TE
R
-1C
O
M
P
U
T
E
R
-2
O
N
/
ST
A
N
D
 B
Y
AUTO
ADJ.
AUDIO OUT S-VIDEO INCOMPUTER 1 IN
COMPUTER  OUTPC CONTROL AUDIO AUDIO
COMPUTER 2 IN
VIDEO INAUDIO
L/MONORAUDIOL/MONOR
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cable's two-pin plug to the AC IN of the projector, and then connect the other plug of
the supplied power cable in the wall outlet.
Make sure that the prongs are fully inserted into
both the AC IN and the wall outlet. To wall outlet 
←
CAUTION:
Do not unplug the power cable from the wall outlet under any one of the following circumstances.
Doing so can cause damage to the projector:
• While the Hour Glass icon appears.
• While the cooling fans are running. The cooling fans continue to work for 30 seconds after the projector is
turned off.