Dukane Imagepro 8767a Portable Lcd Projector Users Manual

23
3.Projecting an Image (Basic Operation)
This section describes how to turn on the projector and to project a picture onto the screen.

 Turning on the Projector
NOTE:
• The projector has two power switches: a main power switch and a POWER (ON/STAND BY) button.
• When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off (
)
position. Failure to do so may cause damage to the projector.
ACIN
ZOOM
FOCUSSTATUSLAMPPOWER
1. To turn on the main power...

24
3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one
of the 8 menu languages.
To select a menu language, follow these steps:
1. Use the SELECT 
 or  button to select one of the 8
languages for the menu.LAMP
STATUS
POWER VIDEO
AUTO
ADJ.
S-VIDEO COMPUTER-1 COMPUTER-2
ON/STAND BY
SELECT
ENTEREXIT MENUUP MAGNIFY PAGEOFF
POWERON
PIC-MUTE
DOWN...

25
3. Projecting an Image (Basic Operation)
 Selecting a Source
Selecting the computer or video source
VIDEO S-VIDEO COMPUTER-1 COMPUTER-2
LAMP
STATUS
POWER
AUTO
ADJ.ON/STAND BY
SELECT
VOLUMEL-CLICK
MOUSER-CLICK
AUTO ADJ.
ASPECT HELP
FREEZE PICTURE
S-VIDEOVIDEOCOMPUTER1
2
NOTE: Turn on the computer or VCR connected to the projector.
Using the cabinet buttons
Press any one of the COMPUTER 1/2 
VIDEO and S-VIDEO buttons.
The corresponding indicator will light green.
Using the Remote Control (8767A/8070)...

26
3. Projecting an Image (Basic Operation)
Detecting the Signal Automatically
Press and hold the SOURCE button for a minimum of 1 second, the
projector will search for the next available input source. Each time you
press and hold the SOURCE button for a minimum of 1 second, the
source will change as follows:
8771
Computer 1 →Computer 2 → Video → S-Video →Computer 1 → ...
If no input signal is present, the input will be skipped.
SOURCE PIC-MUTE
POWER ASPECT
8771 

27
3. Projecting an Image (Basic Operation)
Place your projector on a flat level surface and ensure that the projector is
square to the screen.
Lift the front edge of the projector to center the image vertically.
* If the projected image does not appear square to the screen then use the
Keystone feature for proper adjustment. See page 
29.
 Adjusting the Picture Size and Position
A
C
I
N
Z
OO
MFOCU
S
AC IN
ZOOMFOCU
S
Adjust the Tilt Foot
1. Lift the front edge of the projector.
2. Push up the Adjustable...

28
3. Projecting an Image (Basic Operation)
ACIN
ZOOMFOCU
S
ZOO
M
FO
C
U
S
ACIN
ZOOMFOCU
S
FO
C
U
S
Focus
Use the FOCUS ring to obtain the best focus.
Zoom
Use the ZOOM lever to finely adjust the image size on the
screen.
NOTE: Digital Zoom can cause result in a blurry image because
zooming is made electronically.
8767A/8070/8771 

29
 Correcting Keystone Distortion
Auto Keystone Correction
The Auto Keystone correction feature will correct the vertical distortion of a projected image on the screen. No special
operation required. Just put the projector on a flat surface.
Note that the vertical keystone angle can be corrected between 30 degrees upward and 30 degrees downward of
projector tilt from level.
3. Projecting an Image (Basic Operation)
NOTE: Auto and Manual Keystone correction angle could be less than 30 degrees depending...

30
3. Projecting an Image (Basic Operation)
5. Press the MENU button to close the menu.
NOTE: You can save the changes using the Keystone Save
feature when you turn off the projector. See page 42. 

31
3. Projecting an Image (Basic Operation)
 Optimizing RGB Picture Automatically
Adjusting the Image Using Auto Adjust
Optimizing an RGB image automatically.
Press the Auto Adjust button to optimize an RGB image automatically.
[Poor picture]
[Normal picture]
VIDEO
AUTO
ADJ.
S-VIDEO COMPUTER-1 COMPUTER-2
VOLUMES-VIDEOVIDEO L-CLICK
MOUSER-CLICK
AUTO ADJ. COMPUTER
ASPECT HELP
FREEZE PICTURE
1
2
Press the Auto Adjust button to fine-tune the computer image or to remove any vertical banding that might appear...

32
 Turning off the Projector
To turn off the projector:
3. Projecting an Image (Basic Operation)
LAMP
STATUS
POWER VIDEO
AUTO
ADJ.
S-VIDEO COMPUTER-1 COMPUTER-2
ON/STAND BY
SELECT
POWER
SOURCE PIC-MUTE
ASPECT
SELECT
L-CLICK
ENTEREXIT MENUUP MAGNIFY PAGEOFF
POWERON
PIC-MUTE
DOWN
R-CLICK
First, press the POWER (ON/STAND BY) button on the
projector cabinet or the POWER OFF button on the re-
mote control. The “Power Off / Are you sure?” message
will appear.
CAUTION
Do not unplug the power cable from the...