Dukane Imagepro 8767 Liquid Crystal Projector Users Manual

Liquid Crystal Projector
Model 8767/8054
USERS MANUAL 

E-2
Safety Cautions
Precautions
Please read this manual carefully before using your Dukane
8766/8767/8054  Projector and keep the manual handy for future refer -
ence. Your  serial number is located on the bottom of your projecto r. 
CAUTION
To   turn off main power, be sure to remove the plug from power
outlet.
The power outlet socket should be installed as near to the
equipment as possible, and should be easily accessible.
CAUTION
TO  PREVENT SHOCK, DO NOT OPEN THE CABINET.
NO USER-SERVICEABLE PARTS...

E-3
Fire and Shock Precautions
1. Ensure that there is sufficient ventilation and that vents are unob-structed to prevent the build-up of heat inside your projector. Allow
at least 3 inches (10 cm) of space between your projector and a
wall.
2. Prevent foreign objects such as paper clips and bits of paper from falling into your projector.
Do not attempt to retrieve any objects that might fall into your pro-
jector. Do not insert any metal objects such as a wire or screwdriver
into your projector. If...

E-4
TABLE OF CONTENTS
Important Information ..................................................... E-2Safety Cautions ........................................................................\
....................................... E -2
Whats in the Box? ........................................................................\
.................................. E-3
INTRODUCTION .............................................................. E-5Introduction to the Projector...

E-5
INTRODUCTION
Introduction to the ProjectorThis section introduces you to your new Dukane Projector
and describes the features and controls.
Congratulations on  Your Pu rchase of The  Projector
The Dukane 8766  is one of the very best projectors available
toda y.  The  Dukane 8766  enables you to project precise images
up to 300 inches across (measured diagonally) from your PC or
Macintosh computer (desktop or notebook), VCR, DVD player, docu-
ment camera, or a laser disc player.
Y ou can use the...

E-6
Part Names of the Projector
Ventilation (outlet)
Heated air is exhausted from here
* This security slot supports the MicroSaver® Security System. MicroSaver® is a registered trademark of Kensington Microware Inc. The logo is
trademarked and owned by Kensington Microware Inc.
Built-in Security Slot (  )*
Adjustable Tilt Foot Lever
(See page E-18)
Attaching the lens cap
To  attach the lens cap to the bottom with the supplied string and rivet:
Remote Sensor (See page E-10)
Controls (See page E-7)
V...

E-7
76510
131912
823411
Top Features
1. POWER Button (ON / STAND BY)(  )
Use this button to turn the power on and off when the main power is
supplied and the projector is in standby mode.
To  turn on the projector, press and hold this button for a minimum of
two seconds. To turn off the projector, press this button twice.
2. POWER Indicator When this indicator is green, the projector is on; when this indicator
is orange, it is in standby mode. See the Power Indicator section on
page E-32 for more...

E-8
1. RGB IN / Component Input Connector (Mini D-Sub 15 Pin)Connect your computer or other analog RGB equipment such as IBM
compatible or Macintosh computers. Use the supplied RGB cable to
connect to your computer. This also serves as a component input
connector that allows you to connect a component video output of
component equipment such as a DVD player. This connector also
supports SCART output signal. See page E-14 for more details.
2. RGB AUDIO Input Mini Jack (Stereo Mini) This is where you...

E-9
Part Names of the Remote Control
NOTE: If you are using a Macintosh computer, you can click either the CANCEL(right-click) or ENTER (left-click) button to activate the mouse.
1. Infrared Transmitter
Direct the remote control toward the remote sensor on the projector
cabinet.
2. LED Flashes when any button is pressed.
3. POWER ON Button When the main power is on, you can use this button to turn your
projector on.
NOTE:  To turn on the projector, press and hold the POWER ON button for aminimum of two...

E-10
Battery Installation
1. Press firmly and slide the battery cover off.2. Remove both old batteries and install new ones (AA). Ensure thatyou have the batteries polarity (+/-) aligned correctly.
3. Slip the cover back over the batteries until it snaps into place. Do not\
mix different types of batteries or new and old batteries.
Note on Remote Control Operation:
If you press and hold the SELECT  GHFE button while installing new
batteries, the remote control may fail to work properly.
Should this...