Dukane Imagepro 8762 Portable Lcd Projector Users Manual

13
2. Installation and Connections
PC CONTROL
AUDIO IN
S-VIDEO IN
VIDEO INCOMPUTER IN
COMPUTER IN
Before connections: An exclusive SCART adapter (ADP-SC1) and a commercially available SCART cable are re-
quired for this connection.
F rom the menu, select [Setup - Options]  → [Signal Select]  → [Computer]  → [Scart].
SCART is a standard European audio-visual connector for TVs, VCRs and DVD players. It is also referred to as Euro-
connector.
NOTE: Audio signal is not available for this connection.
TIP:...

14
AUDIO INLR
AUDIO OUT
LR
Component
YCbCr
COMPUTER IN PC CONTROLS-VIDEO IN
VIDEO INAUDIO IN
COMPUTER INAUDIO IN 
2. Installation and Connections
A component signal will be automatically displayed. If not, from the menu, select [Setup - Options]  → [Signal Select]  →
[Computer], and then place a check mark in the “RGB/Component” radio button.
NOTE: Refer to your DVD players owners manual for more information abo\
ut your DVD players video output requirements.
Connecting Your DVD Player with Component...

15
2. Installation and Connections
AUDIO INLRAUDIO OUTLRVIDEO OUTS-VIDEO
VIDEO
COMPUTER IN PC CONTROL AUDIO IN
S-VIDEO IN
VIDEO IN
VIDEO INAUDIO IN
S-VIDEO IN
Connecting Your VCR or Laser Disc Player
S-Video cable (not supplied)
Video cable (not supplied)
VCR/ Laser disc player
Audio equipment
A udio cable (not supplied)
NOTE: Refer to your VCR or laser disc player owners manual for more inf\
ormation about your equipments video output require-
ments.
NOTE:
• An image may not be displayed correctly when...

16
2. Installation and Connections
COMPUTER INAUDIO IN
S-VIDEO IN
VIDEO IN
LAMP
STATUS
POWER
SOURCE AUTO ADJ.
FOCUS
ON/STAND BYS ELE CT
PC CONTROL
LAMP
STATUS
ON/STAPOWER
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cables three-pin plug to the AC IN of the projector, and then connect the other plug
of the supplied power cable in the wall outlet.
Make sure that the prongs are fully inserted into both the power plug and the wall...

17
3. Projecting an Image (Basic Operation)
This section describes how to turn on the projector and to project a picture onto the screen.

 Turning on the Projector
NOTE: Before turning on the projector, first connect the supplied power cables three-pin plug to the AC IN of the projector, a nd then
connect the other plug of the supplied power cable in the wall outlet. M\
ake sure that the projector is in its standby mode and  the
power indicator is glowing orange.
1. Remove the lens cap.
POWER
STATUS...

18
EXIT
MENU
UP
PAGE
OFF
POWER ON
PIC-MUTE
DOWN
FOCUS
ENTER
FOCUS
SELECT
FOCUS
SELECT
3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one
of the nine menu languages.
To  select a menu language, follow these steps:
1. Use the SELECT 
 or  b utton to select one of the
nine langua ges fr om the men u.
2.Press the ENTER b utton to execute the...

19
3. Projecting an Image (Basic Operation)

 Selecting a Source
Selecting the computer or video source
LAMP
STATUS
POWER
SOURCE AUTO ADJ. FOCUS
ON/STAND BY
SELECT
LAMP MODE
VOLUME S-VIDEO
VIDEO
L-CLICK
MOUSE
R-CLICK
AUTO ADJ.
COMPUTER
ASPECT HELP
FREEZE
PICTURE
NOTE: Turn on the computer or VCR connected to the projector.
Selecting a source from the Source list
Press and quickly release the SOURCE button on the projector cabinet
to display the Source list. Each time the SOURCE button is pressed,
each...

20
3. Projecting an Image (Basic Operation)
Place your projector on a flat level surface and ensure that the
projector is square to the screen.
Lift the front edge of the projector to center the image vertically.
*If the projected image does not appear square to the
screen then use the Keystone feature for proper adjust-
ment. ( → page 
25 )
 Adjusting the Picture Size and Position
About Auto Focus
Just placing the projector on a flat level surface makes a focused
image. ( → page 
22 )
Move the...

21
2
LAMP
ST ATUS
P O WERSO
URC
E
AU
TO
 A D J. F
O C
US
O
N/S TA N
D B YSE LEC T
13
3. Projecting an Image (Basic Operation)
Adjust the Tilt Foot
1. Lift the front edge of the projector.
CAUTION:
Do not try to touch the ventilation outlet during Tilt Foot adjustment
as it can become heated while the projector is turned on and during
its cool down period after it is turned off.
2. Push and hold the Adjustable Tilt Foot Button on the front of
the projector to extend the adjustable tilt foot (maximum...

22
3. Projecting an Image (Basic Operation)
Zoom
Use the ZOOM lever to adjust the image size on the screen.
NOTE: Rotating the ZOOM lever will cause the focus to be ad-
justed automatically.
Auto Focus
The focus sensor on the projector detects the distance to the screen and auto\
matically adjusts the focus of an image.
• The Auto Focus function will work when the following tasks are done:
-T urning on the power
- Changing the zoom lever
- Repositioning the projector
- Changing the projection angle...