Dukane Imagepro 8755n Projector Users Manual

							51
SCREEN menu
ItemDescription
MyScreen This item allows you to capture an image for use as a MyScreen 
image which can be used as the BLANK screen and START UP 
screen. Display the image you want to capture before executing the 
following procedure.
  Selecting this item displays a dialog 
titled “MyScreen”. It will ask you if 
you start capturing an image from the 
current screen. Please wait for the 
target image to be displayed, and press 
the ENTER or INPUT button to start 
registration.
To restore the screen and return to 
the previous dialog, press the 
RESET 
button on the remote control. 
Registration may take several minutes. 
When the registration is completed, 
the registered screen and the following 
message is displayed for several 
seconds:
“MyScreen registration is finished.”
If the registration failed, the following message is displayed: “A capturing error has occurred. Please try again.” 
• This function cannot be selected when the ON is selected to the 
MyScreen Lock item (
 52).
• This function cannot be selected when the ON is selected to the 
MyScreen PASSWORD item in SECURITY menu (
 79).
• This function is unavailable for a signal from the LAN, USB TYPE A, 
USB TYPE B or HDMI port.
(continued on next page) 
						

							52
SCREEN menu
ItemDescription
MyScreen Lock Using the ▲/▼ buttons turns on/off the MyScreen lock function.
ON  ó OFF
When the ON is selected, the item MyScreen is locked. Use this 
function for protecting the current MyScreen.
• This function cannot be selected when the ON is selected to the 
MyScreen PASSWORD item in SECURITY menu (
 79).
MESSAGE Using the ▲/▼ buttons turns on/off the message function.
ON  ó OFF
When the ON is selected, the following message function works. “AUTO IN PROGRESS” while automatically adjusting
“NO INPUT IS DETECTED”
“SYNC IS OUT OF RANGE”
“INVALID SCAN FREQ.”
“NOT AVAILABLE.”
“Searching….” while searching for the input
“Detecting….” while an input signal is detected
“AUTO ECO MODE” while starting up with AUTO ECO MODE 
The indication of the input signal displayed by changing 
The indication of the aspect ratio displayed by changing
The indication of the PICTURE MODE displayed by changing
The indication of the MY MEMORY displayed by changing
The indication of “FREEZE” and “II” while freezing the screen by 
pressing the  FREEZE button.
The indication of the TEMPLATE displayed by changing.
The indication of the ECO MODE displayed by changing.
• When the OFF is selected, please remember if the picture is 
frozen. Do not mistake freezing for a malfunction  (
31).
(continued on next page) 
						

							53
SCREEN menu
ItemDescription
SOURCE NAME Each input port for this projector can have a name applied to it.
(1)  
Use the ▲/▼ buttons on the SCREEN menu to select SOURCE 
NAME and press the ► or ENTER button.  
The SOURCE NAME menu will be displayed.
(2)   Use the ▲/▼ buttons on the SOURCE 
NAME menu to select the port to be 
named and press the ► button. The 
SOURCE NAME dialog will be displayed. 
Right side of the menu is blank until a 
name is specified.
(3)   Select an icon you would like to assign to  
the port in the SOURCE NAME dialog.  
The name assigned to the port will also  
be automatically switched according to  
your icon selection. Press the  ENTER or  
INPUT button to determine your icon selection.
(4)   Select a number you would like to assign  
to the port along with the icon. You can  
select the number either from blank  
(no number assigned), 1, 2, 3, or 4.  
Then press the ENTER or INPUT button.
(5)   If you would like to modify the name assigned  
to the port, select CUSTOM NAME and  
press the ENTER or INPUT button. 
(continued on next page)
(continued on next page) 
						

							54
SCREEN menu
ItemDescription
SOURCE NAME (continued )(6) 
 
The current name will be displayed on 
the first line. Use the ▲/▼/◄/► buttons 
and the ENTER or INPUT button to 
select and enter characters. To erase 1 
character at one time, press the RESET 
button or press the ◄ and INPUT button 
at the same time. Also if you move the 
cursor to DELETE or ALL CLEAR on 
screen and press the  ENTER or INPUT 
button, 1 character or all characters will 
be erased. The name can be a maximum 
of 16 characters.
(7)    To change an already inserted character, 
press the ▲ button to move the cursor to 
the first line, and use the ◄/► buttons to 
move the cursor on the character to be 
changed. 
After pressing the ENTER or INPUT button, the character is 
selected.  Then, follow the same procedure as described at the 
item (6) above.
(8)    To finish entering text, move the cursor to the OK on screen and 
press the ►, ENTER or INPUT button. To revert to the previous 
name without saving changes, move the cursor to the CANCEL 
on screen and press the ◄, ENTER or INPUT button.
TEMPLATE Using the ▲/▼ cursor buttons switches the mode for the template 
screen.
Press the ► cursor (or the ENTER) button to display the selected 
template, and press the ◄ cursor button to close the displayed 
screen.
The last selected template is displayed when the 
MY BUTTON
allocated to the TEMPLATE function is pressed (
 59).
TEST PATTERN  ó DOT-LINE1 
ó DOT-LINE2 
ó DOT-LINE3
                                                                                          

             MAP2 
ó MAP1 
ó CIRCLE2 
ó CIRCLE1 
ó DOT-LINE4
You can turn a map upside down and scroll it horizontally when 
MAP1 or MAP2 is selected. To invert or scroll the map, display 
the guidance by pressing the  RESET button on the remote three 
seconds or more when MAP1 or MAP2 appears.
(continued on next page) 
						

							55
SCREEN menu
ItemDescription
C.C.
(Closed Caption) The C.C. is the function that displays a 
transcript or dialog of the audio portion of 
a video, files or other presentation or other 
relevant sounds. It is required to have NTSC 
format video or 480i@60 format component 
video source supporting C.C. feature to 
utilize this function.
It may not work properly, depending on equipment or signal source. 
In this case, please turn off the Closed Caption.
DISPLAY
Select Closed Caption DISPLAY setting from following options using 
▲/▼ buttons.
AUTO  ó ON 
ó OFF 
   
AUTO :   Closed Caption automatically displays when the volume 
is muted.
ON : Closed Caption is on.
OFF : Closed Caption is off.
• The caption is not displayed when the OSD menu is active.
• The Closed Caption is the function to display the dialogue, 
narration, and / or sound effects of a television program or other 
video sources. The Closed Caption availability is depending upon 
broadcaster and/or content.
MODE
Select Closed Caption MODE setting from following options using 
▲/▼ buttons.
CAPTIONS  ó TEXT
CAPTIONS : Display Closed Caption.
TEXT :   Display Text data, which is for additional information such 
as news reports or a TV program guide. The information 
covers the entire screen. Not all of the C.C. program has 
Text information.
CHANNEL
Select Closed Caption CHANNEL from following options using ▲/▼ 
buttons.
1 ó  2 
ó 3 
ó 4
1: Channel 1, primary channel / language
2: Channel 2
3: Channel 3
4: Channel 4
The channel data may vary, depending on the content. Some 
channel might be used for secondary language or empty. 
						

							56
OPTION menu
OPTION menu
From the OPTION menu, items shown in the table 
below can be performed.
Select an item using the ▲/▼ cursor buttons, and 
press the ► cursor button or ENTER button to execute 
the item, except for the items LAMP TIME and FILTER 
TIME. Then perform it according to the following table.
ItemDescription
AUTO SEARCH Using the ▲/▼ buttons turns on/off the automatic signal search 
function.
ON  ó OFF
When the ON is selected, detecting no signal automatically cycles 
through input ports in the following order. The search is started from 
the current port. Then when an input is found, the projector will stop 
searching and display the image.   
COMPUTER IN1  ð COMPUTER IN2 
ð LAN 
ð USB TYPE A 
            VIDEO   S-VIDEO 
 HDMI
 USB TYPE B
• It may take several seconds to project the images from the  
USB TYPE B port.
AUTO 
KEYSTONE
Using the ▲/▼ buttons turns on/off the automatic keystone function.
ON  ó OFF
ON :   
Automatic keystone distortion correction will be executed 
whenever changing the slant of the projector.
OFF :    This function is disabled. Please execute the AUTO 
KEYSTONE (EXECUTE) in the SETUP menu for automatic 
keystone distortion correction.
• When the projector is suspended from the ceiling this feature will 
not function properly so select the OFF.
• 
This function will be unavailable when the TRANSITION DETECTOR 
is on ( 81).
DIRECT POWER  ON Using the ▲/▼ buttons turns on/off the DIRECT POWER ON 
function.
ON  ó OFF
When set to the ON, the lamp in projector will be automatically turned 
on without the usual procedure (
 21)
, only when the projector is 
supplied with the power after the power was cut while the lamp was on.
• This function does not work as long as the power has been 
supplied to the projector while the lamp is off.
• 
After turning the lamp on by the DIRECT POWER ON function, 
if neither input nor operation is detected for about 30 minutes, the 
projector is turned off, even though the AUTO 
POWER OFF function 
(
 57) is disabled.
(continued on next page) 
						

							57
OPTION menu
ItemDescription
AUTO POWER  OFF Using the ▲/▼ buttons adjusts the time to count down to 
automatically turn the projector off.
Long (max. 99 minutes)  ó Short (min. 0 minute = DISABLE)
When the time is set to 0, the projector is not turned off automatically.When the time is set to 1 to 99, and when the passed time with  
no-signal or an unsuitable signal reaches at the set time, the 
projector lamp will be turned off. 
If one of the projector's buttons or the remote control buttons 
is pressed or one of the commands (except get commands) is 
transmitted to the CONTROL port during the corresponding time, 
projector will not be turned off.
Please refer to the section Turning off the power
 ( 22).
LAMP TIME The lamp time is the usage time of the lamp, counted after the last 
resetting. It is shown in the OPTION menu.
Pressing the RESET button on the remote control or the ► button 
of the projector displays a dialog. 
To reset the lamp time, select the OK using the ► button.
CANCEL
 ð  OK
• Please reset the lamp time only when you have replaced the lamp, 
for a suitable indication about the lamp.
• 
For the lamp replacement, see the section Replacing the lamp ( 108).
FILTER TIME The filter time is the usage time of the air filter, counted after the last 
resetting. It is shown in the OPTION menu.
Pressing the RESET button on the remote control or the ► button 
of the projector displays a dialog. 
To reset the filter time, select the OK using the ► button.
CANCEL ð  OK
• 
Please reset the filter time only when you have cleaned or replaced 
the air filter, for a suitable indication about the air filter.
• For the air filter cleaning, see the section  Cleaning and replacing 
the air filter (
 110).
(continued on next page) 
						

							58
OPTION menu
ItemDescription
MY BUTTON This item is to assign one of the following functions to 
MY BUTTON 
1/2 on the remote control (
 6).
(1)   Use the ▲/▼ buttons on the MY BUTTON menu to select a MY 
BUTTON - (1/2) and press the ► or ENTER button to display the 
MY BUTTON setup dialog. 
(2)   Then using the ▲/▼/◄/► buttons sets one of the following 
functions to the chosen button. Press the ENTER or INPUT 
button to save the setting.
• COMPUTER IN1: Selects the input from COMPUTER IN1 port.
• COMPUTER IN2: Selects the input from COMPUTER IN2 port.
• LAN: Selects input from LAN port.
• USB TYPE A: Selects input from USB TYPE A port.
• USB TYPE B: Selects input from USB TYPE B port.
• HDMI: Selects input from HDMI port.
• S-VIDEO: Selects the input from S-VIDEO port.
• VIDEO: Selects the input from VIDEO port.
• 
SLIDESHOW: Selects the input from USB TYPE A, and starts a Slideshow.•   MY IMAGE: Displays the MY IMAGE menu ( 75).
•   MESSENGER: Turns the messenger text displayed on the screen on/off (Messenger Function in the Network Guide ). 
When there is no transferred text data to display, the message 
”NO MESSENGER DATA" appears.
•   INFORMATION: Displays SYSTEM_INFORMATION,  
INPUT_INFORMATION  (
66), WIRELESS INFORMATION 
( 71), WIRED INFORMATION (73) or nothing.
•    AUTO KEYSTONE : Performs automatic keystone distortion 
correction (
 46).
•   MY MEMORY: Loads one of adjustment data stored (
 38). 
When more than one data are saved, the adjustment  
changes every time the  MY BUTTON is pressed.
When no data is saved in memory, the 
dialog "No saved data" appears.
When the current adjustment is not 
saved to memory, the dialog as shown in 
the right appears.
If you want to keep the current adjustment, please press  
the ► button to exit. Otherwise loading a data will overwrite the 
current adjusted condition.
(continued on next page)
(continued on next page) 
						

							59
OPTION menu
ItemDescription
MY BUTTON (continued )• ACTIVE IRIS: Changes the active iris mode.
• PICTURE MODE: Changes the PICTURE MODE (

34).
•  FILTER RESET: Displays the filter time reset confirmation dialogue  ( 57).
•    TEMPLATE: Makes the template pattern selected to the 
TEMPLATE item (
 54) appear or disappear.
•    AV MUTE: Turns the picture and audio on/off.
•   RESOLUTION: Turns on/off the RESOLUTION dialog (
 45).
•   MIC VOLUME: Turns on/off the MIC VOLUME dialog ( 49).
•   ECO MODE: Changes the ECO MODE ( 47).
•  SAVER MODE: Turns on/off the SAVER MODE  ( 47 ECO MODE).
MY SOURCE Using ▲/▼ buttons selects the picture input port to be selected with 
pressing the 
MY SOURCE/DOC.CAMERA  button on the remote 
control.
You can use this function not only for document cameras but also 
computers and other equipment.
  VIDEO  ó COMPUTER IN1 
ó COMPUTER IN2 
ó LAN 
  S-VIDEO  ó HDMI 
ó USB TYPE B 
ó USB TYPE A
SERVICE Selecting this item displays the SERVICE 
menu.
Select an item using the ▲/▼ buttons, 
and press the ► button or the ENTER 
button on the remote control to execute 
the item.
ALTITUDE
Using the ▲/▼ buttons switches the rotation speed of the cooling fans. 
The HIGH is the mode for use at highlands etc. If the projector is used
at an altitude of about 1600 m (5250 feet) or higher, select HIGH. 
Otherwise, select NORMAL. Note that the projector is noisier when the 
HIGH is selected.
HIGH 
ó NORMAL
(continued on next page) 
						

							60
OPTION menu
ItemDescription
SERVICE
(continued)
AUTO ADJUST
Using the ▲/▼ buttons to select one of the mode. When the 
DISABLE is selected, the automatic adjustment feature is disabled.
FINE  ó FAST 
ó DISABLE
   
FINE: Finer tuning including H.SIZE adjustment.
FAST:   Faster tuning, setting H.SIZE to prearranged data for the 
input signal.
• 
Depending on conditions, such as input image, signal cable to the 
projector, environment around the projector, etc., the automatic adjustment 
may not work correctly.  In such a case, please choose DISABLE to 
disable the automatic adjustment, and make adjustment manually.
GHOST
Adjust the settings using the ▲/▼ buttons to eliminate ghosting.
FILTER MESSAGE
Use the ▲/▼ button to set the timer for notifying by the message 
when to replace the filter unit 
             100h  ó ········· 
ó 5000h 
ó OFF
After choosing an item except OFF, the message “REMINDER *** 
HRS PASSED ....” will appear after the timer reaches the interval 
time set by this feature (
 114). 
When the OFF is chosen, the message will not appear. Utilize this 
feature to keep the air filter clean, setting the suitable time according 
to your environment of this projector.
• Please take care of the filter unit periodically, even if there is 
no message. If the air filter becomes to be blocked by dust or 
other matter, the internal temperature will rise, which could cause 
malfunction, or reduce the lifetime of the projector.
• Please be careful with the operating environment of the projector 
and the condition of the filter unit.
KEY LOCK
(1)   Use the ▲/▼ buttons to choose the operations control.
CONTROL PANEL  ó REMOTE CONTROL
(2)   
Use the ◄/► buttons to select ON or OFF.
ON 
ó OFF
Selecting ON in Step 2 locks the buttons except  STANDBY/ON on 
the operations control selected in Step 1. Selecting OFF releases 
the locked buttons on the operations control selected in Step 1.
• Please use this function to prevent tampering or accidental 
operation. 
(continued on next page)