Dukane Imagepro 8755j Projector Users Manual

11
Setting up
Connecting power supply
1.Put the connector of the power cord into the 
AC IN (AC inlet) of the projector.
2.Firmly plug the power cord’s plug into the 
outlet. In a couple of seconds after the 
power supply connection, the POWER 
indicator will light up in steady orange.
►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, consult...

12
30º30º
Approx.
3 m 
Remote control
Remote control
About the remote control signal
The remote control works with the projector’s remote 
sensor. This projector has a remote sensor on the front.
The sensor senses the signal within the following range 
when the sensor is active: 60 degrees (30 degrees to the left and right of the sensor) 
within 3 meters about.
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote control 
starts to malfunction, try...

13
Remote control
Changing the frequency of  remote control signal
The accessory remote control has the two choices on signal 
frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control 
does not function properly, attempt to change the signal frequency.
In order to set the Mode, please keep pressing the combination of 
two buttons listed below simultaneously for about 3 seconds.
Using as a simple PC mouse & keyboard
The accessory remote control works as a simple mouse 
and keyboard of the PC, when...

14
Power on/off
1.Make sure that the power cord is firmly and 
correctly connected to the projector and the 
outlet.
Turning on the power
2.Make sure that the POWER indicator is 
steady orange (
59). Then remove the lens 
cover.
3.Press STANDBY/ON button on the 
projector or the remote control.
The projection lamp will light up and  POWER  
indicator will begin blinking in green. When the power  
is completely on, the indicator will stop blinking and light in steady green 
(
59).
Power on/off
To...

15
Operating
Operating
1.
Adjusting the volume
Use the VOLUME +/VOLUME - buttons to adjust the volume. 
A dialog will appear on the screen to aid you in adjusting the 
volume. If you do not do anything, the dialog will automatically 
disappear after a few seconds.
●   When 
 is selected for current picture input port, the volume 
adjustment is disabled. Please see AUDIO SOURCE item of 
AUDIO menu (
36).
●   When the projector is in the standby mode, the volume can be  
adjusted if 
 is not selected for...

16
VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCH
BLANK
MUTE
MY BUTTON
POSITION
12
ESC ENTERMENURESET
COMPUTER
MY SOURCE/AUTO
MAGNIFYPAGE
      UPVOLUME
DOWNo
ONOFF
9×
FREEZE
Operating
1.Press VIDEO button on the remote control.  
Each time you press the button, the projector switches its 
input port from the current port as below.
Selecting an input signal (continued)
●   While ON is selected for AUTO SEARCH item in OPTION 
menu, the projector will keep checking every port sequentially 
till an input signal is...

17
1.Press ASPECT button on the remote control.   
Each time you press the button, the projector switches the 
mode for aspect ratio in turn. 
Selecting an aspect ratio
● ASPECT button does not work when no proper signal is inputted.
● NORMAL mode keeps the original aspect ratio setting.
1.Press SEARCH button on the remote control.
The projector will start to check its input ports as below in 
order to find any input signals.
When an input is found, the projector will stop searching 
and display the...

18
Operating
Adjusting the projector's elevator
When the place to put the projector is slightly uneven to the left or right, use the 
elevator feet to place the projector horizontally. 
Using the feet can also tilt the projector in order to project at 
a suitable angle to the screen, elevating the front side of the 
projector within 14 degrees.
This projector has 2 elevator feet and 2 elevator buttons. An elevator foot is 
adjustable while pushing the elevator button on the same side as it.
1.Holding...

19
Operating
1.Press POSITION button on the remote control when no menu is 
indicated. 
The “POSITION” indication will appear on the screen.
Adjusting the position
2.Use the ▲/▼/◄/► cursor buttons to adjust the picture position.
When you want to reset the operation, press  RESET button on 
the remote control during the operation.
To complete this operation, press POSITION  button again. Even if 
you do not do anything, the dialog will automatically disappear 
after a few seconds.
●  
When this function...

20
Operating
• The zoom level can be finely adjusted. Closely watch the screen to 
find the level you want. NOTE
1.Press the ON button of MAGNIFY on the remote control.  
The “MAGNIFY” indication will appear on the screen and the 
projector will go into the MAGNIFY mode. When the ON button 
of MAGNIFY is pressed first after the projector is started, the 
picture will be zoomed twice. The indication will disappear in 
several seconds with no operation.
Using the magnify feature
2.Use the ▲/▼ cursor...