Dukane Imagepro 8755b Liquid Crystal Projector Users Manual

							ENGLISH
9
WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED (continued)
Phenomena That May Easily Be Mistaken for Machine Defects
Before requesting repair, check in accordance with the following chart.
If the situation cannot be corrected, then contact your dealer.
Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and
such do not constitute or imply a machine defect. 
NOTE
PhenomenonCases not involving a machine defectItems to be confirmedReference
Page(s)
Power does not
come ON
The main power source is not ON.Turn on the main power.Vol.1-3, 14The electrical power cord is not plugged in.Correctly connect the power cord.
The main power source has been
interrupted during operation, such as by
a power outage (blackout), etc.Be sure to press the “O” (power OFF) side
of the main power switch, and leave this OFF
for approximately 20 minutes. After the unit
has sufficiently cooled down, turn ON the
power source.
Vol.1-14
No sound or
pictures are
outputtedThe input changeover settings
are mismatched.Select the input signal, and
correct the settings.Vol.1-15
No signal is being inputted.Correctly connect the connection cord.Vol.1-10, 11
Pictures are
displayed, but no
sounds are heard
The electrical wiring to this unit
is not correctly connected.Correctly connect the connection cord.Vol.1-10, 11
The volume setting has been set at (or
adjusted to) an extremely low level.Adjust the VOLUME setting to a higher level.Vol.1-17
The MUTE mode is the current setting.Press the MUTE button to release
(change) the MUTE mode setting.Vol.1-17
Sounds are
heard, but no
pictures are
displayed
The electrical wiring to this unit
is not correctly connected.Correctly connect the connection cord.Vol.1-10, 11
The brightness setting has been set at
(or adjusted to) an extremely low level.Adjust the BRIGHT setting to a
brighter level.Vol.2-2
The lens cap has not been removed.Remove the lens cap.Vol.1-14
Colors have a faded-
out appearance
Color tone is poorColor depth setting or color tone settingPerform picture adjustments by changing the
COLOR BAL R, the COLOR BAL B, and/or the
TINT settings, etc.
Vol.2-3
Pictures appear
dark
The brightness setting and/or contrast
setting has not been properly adjusted.Perform picture adjustments by changing the
BRIGHT and/or CONTRAST settings, etc.Vol.2-2
The WHISPER mode is the current
setting.Change (by releasing) from the
WHISPER mode.Vol.2-6
Lamp is approaching the end of its
product lifetime.Exchange the old lamp with a new
lamp.Vol.1-25, 26
Pictures appear
blurryEither the FOCUS setting or the H
PHASE is not properly adjusted.Adjust the FOCUS and H PHASE settings.Vol.1-15
Vol.2-3 
9
&%497PM&/(
 
 
 
 .
 
 
						

							Dimension Diagram
Unit : mm
77.5
295
237
87.5
37
50.5231
ItemSpecification
Product nameLiquid crystal projector
Liquid 
crystal
panelPanel size1.8 cm (0.7 type)
Drive systemTFT active matrix
PixelsED-S3170A 480,000 pixels (800 horizontal x600 vertical)
ED-X3270A 786,432 pixels (1024 horizontal x 768 vertical)
LensZoom lens F=1.7 ~ 1.9  f=21.7 ~ 26.1 mm
Lamp150 W UHB
Speaker1.0W
Power supplyAC100 ~ 120V, 2.7A / AC220 ~ 240V, 1.3A
Power consumption240W
Temperature range0 ~ 35°C (Operating)
Size295 (W) x 87.5 (H) x237 (D) mm
Weight (mass)2.7 kg
Ports
Optional PartsLamp:=DT00521 
Air Filter: MU01691
* For others, consult your dealer.
RGB Ports 
RGB IN(1, 2) ..................2
VIDEO Ports
VIDEO IN ........................1
S-VIDEO IN ....................1
AUDIO Ports
AUDIO IN(1,2) ................2
AUDIO IN(R, L) ..............1 RGB OUT Ports
RGB OUT ........................1
AUDIO OUT Ports
AUDIO OUT ....................1
CONTROL Ports
CONTROL ......................1
USB ................................1
•This specifications are subject to change without notice.NOTE
SPECIFICATIONS
10
&%49\
7PM\
&/(
 
 
\
 
 .
 
 Ö”´
 
						

							ENGLISH
If a problem occurs with the equipment, first refer to the        “WHAT TO DO WHEN YOU
THINK A MACHINE DEFECT HAS OCCURRED” section and run through the suggested
checks. If this does not resolve the problem contact your dealer or service company. They
will tell you what warranty condition is applied.
WARRANTY AND AFTER-SERVICE
11
7
&%497PM&/(
 
 
 
 .
 
 
						

							DUKANE CORPORATION
FIVE-YEAR LIMITED WARRANTY
This Dukane projector is warranted to the original purchaser for a perio\
d of  five  (5) years from
the original purchase date – in normal operating conditions – agai\
nst defects in material and
workmanship .  DUKANE CORPORATION EXPRESSLY DISCLAIMS ALL OTHER
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
DURING THE WARRANTY PERIOD, DUKANE CORPORATION’S LIABILITY FOR ANY
DEFECTIVE PRODUCT (except for the lamp, which is subject to whatever wa\
rranties the
manufacturer may provide) IS LIMITED TO THE REPAIR OR REPLACEMENT OF
PRODUCT AT DUKANE CORPORATION’S OPTION.  REPLACEMENT PRODUCTS MAY
BE NEW OR  USED (used units will not exceed hours of defective unit). \
 The following are not
covered by the limited warranty and Dukane Corporation shall not be liab\
le for:
1.  Any product which is not distributed in the U.S.A. or Canada by Dukane C\
orporation or an
authorized dealer.
2.   Normal decrease in lamp light output over time.
3.   Damage, deterioration or malfunction resulting from:
·  Accident, misuse, abuse, neglect, improper ventilation, fire, dust, smok\
e, water, lighting
or other acts of nature, unauthorized product modification, or failure t\
o follow
instructions supplied with the product (including proper maintenance of\
 air filters).
·   Repair or attempted repair by anyone other than a Dukane Corporation aut\
horized service
center.
·   Any shipment of product (claims must be presented to the carrier).
·   Removal or installation of the product.
·   Any other causes which do not relate to a product defect.
·   Use of the product beyond normal operating conditions.  Normal operating\
 conditions are
defined as product use not in excess of 8 hours per day and 260 days per\
 year.
4.   Cartons, carry cases, shipping cases, batteries, or any accessories used\
 in connection with the
product.
5.   Service required as a result of third party components.
6.   Product used as commercial rental units
Dukane corporation will pay labor and material expenses for covered item\
s, but Dukane
Corporation will not pay for the following:
1.   Removal or installation charges.
2.   Cost of technical adjustment, set-up, maintenance, or adjustment of user\
 controls.
3.   Payment of shipping and related charges incurred in returning the produc\
t for warranty
repair.
Dukane Corporation disclaims all liability for incidental or consequenti\
al damage of any kind,
including all damages arising out of any interruptions in operation of t\
he product and all damages
to software.
No person, firm, or representative is authorized to assume any obligatio\
n or to make any warranty
on behalf of the Dukane Corporation other than as stated above. 
						

							Dukane CorporationAudio Visual Products Division2900 Dukane DriveSt. Charles, IL 60174-3395E-mail: [email protected]
Phone: (630) 584-2300Orders: (800) 676-2485Information: (800) 676-2486Fax: (630) 584-5156Parts & Service: (800) 676-2487Fax: (630) 584-0984
Audio Visual Products
Part # 401- 8755B-00