Dream Vision Yunzi+ Very High Contrast Video-projector User Manual

PICTURE ADjUST
R699840 - Yunzi+ User Manual21
7.7 	Advanced Gamma
Correction Value
The Custom data can be set to:
Correction Value: a unique value that will act as a gamma coefficient between 1.8 and 2.6, Normal, Brightness 
Priority, Contrast Priority, Gradation Priority, 1.8-2.6 or Import.
Color Selection
Select the color to which the Picture Tone, Dark / Bright Level settings would apply. Choose between White, Red, 
Green and Blue.
Picture Tone
It  allows  a  fine  adjustment  steps  of  the  global...

R699840 - Yunzi+ User Manual
INPUT SIGNAL
22
7.9 	Clear Motion Drive (400Hz)
The Clear Motion function uses a 400Hz video processing to render a smooth and clear motion for movies shot 
at 24Hz or HD movies at 60Hz. Set the correct level between:
• Off: Frame interpolation is disable.
• Low: light frame interpolation with reduced artifacts.
• High: strong interpolation
• Inverse Telecine: dedicated interpolation for 60i and 60p sources originally shot in 24p.
7.10 	Contrast
The contrast function is used...

3D CONTENT AND 3D PROjECTION
R699840 - Yunzi+ User Manual23
8.4 	Aspect Ratio
When watching a movie or video program, you can manually set the desired aspect ratio to fill your screen. Select 
the correct aspect ratio depending on your source:
For Video sources
a) 4:3. The original source is considered as 4:3 format. Generally SDTV broadcasts.
b) 16:9. The picture size is 16:9, generally most recent DVDs, Blu-Ray discs or HDTV broadcasts.
c) Zoom. The zoom function is useful to zoom in the picture and...

R699840 - Yunzi+ User Manual
INSTALLATION
24
9.2 	Projector 3D Settings
3D Formats
Use this function to choose the correct 3D input format. Some input signals may contain 3D data such as 1080p 
Side-by-Side  but  encoded  as  if  they  were  in  2D.  This  unit  may  treat  them  as  standard  2D  signals  and  will  not 
project correctly. In such cases, configure the signal manually between Side-by-Side, Top & Bottom and 2D. In 
other cases, you may select Auto setting.
2D to 3D Conversion
You can use...

INSTALLATION
R699840 - Yunzi+ User Manual25
Lens Memory Save
Store into an available memory the lens focus, zoom and shift configuration. There are 5 memories for Yunzi+1 
model and 10 memories for the Yunzi+2&3.
Lens Memory Name Edit
You can edit the Lens Memory Name within the limit of 10 characters. Same procedure as section “User Name 
Edit”, page 19.
Lens Center
Reset the lens position to the original, central position.
Lens Cover (Yunzi+2&3)
Control the behavior of the Lens Cover:
• Auto: the lens...

R699840 - Yunzi+ User Manual
INSTALLATION
26
Installation Style
Flip the image to the left or right, up or down according to the projection state of the projector:
Front, Ceiling Mount (F), Rear or Rear Ceiling mount (R)
10.3 	Keystone (Vertical)
Compensate for trapezoidal distortion caused by installation. Independently to the screen orientation, make sure 
that the projector is not tilt more than 5% up/down.
• Vertical Keystone from -16 to +16.
10.4 	Pincushion
Compensate distortions that may appear...

DISPLAY SETUP
R699840 - Yunzi+ User Manual27
without altering the global picture settings. You may select the best template available in the Screen No.
a) 001 - 009: select a profile between 001 and 009 when watching 3D content with 3D shutter glasses. Profile 
001 is recommended when using Dreamvision’s active IR 3D-glasses.
b) 010 to 106: select the best compensation profile depending on your screen and environment.
• Screen size: diagonal size in inches set this setting between 60” and 200”.
• Viewing...

R699840 - Yunzi+ User Manual
INFORMATION MENU
28
12.5 	Remote Code A or B
Select  in  the  projector  menu  the  code  A  or  B  according  to  the  code  selected  on  the  RCU.  You  can  change 
the  code  used  by  the  RCU  to  communicate  with  the  projector  from A  to  B.  To  do  so,  press  and  hold  for  3  sec 
simultaneously [MENU]+[BACK] buttons on the RCU. All the buttons on the RCU will blink.
• Two blinks indicate that B code is used.
• Three blinks indicate that A code is used.
12.6...

CINEMASCOPE SETUPS
R699840 - Yunzi+ User Manual29
14.2 	Cinemascope setup with Lens Zoom
Select “Menu => Installation => Lens Memory 1”
Zoom in, until the left and right borders of the picture fits the 2.35:1 screen borders. Save the lens position in the
lens memory 1. You can also edit the memory 1 name to “Cinemascope”.
Select “Menu => Installation => Lens memory 2”
Make sure to project a 16:9 picture, zoom out until the picture top and bottom fit the top and bottom of the screen.
Adjust  the  focus...

R699840 - Yunzi+ User Manual
MAINTENANCE
30
[Anamo]rphic modes
OFFAnamo  Mode A Anamo Mode B
When you press sequentially the [Anamo]rphic button, you change the mode from OFF, Mode A and Mode B.
• Mode A is intended to be used with an anamorphic lens to watch 2.35:1 content on a 2.35:1 screen.
• Mode B is intended to be used to quickly switch to 16:9 content without moving the anamorphic lens.
The Anamorphic Lens is automatically placed in front of the projector to restore the correct picture aspect...