Dream Vision Yunzi 3 User Manual

9.0  INSTALLATION SETTINGS
R699820 - Yunzi Series User Manual 31 
Intensity (2D to 3D Conversion is On)
Because the 2D to 3D Conversion may not detect the correct depth of the picture elements, you can use this
function to enhance the depth perception during the conversion. Adjust setting from 1 up to 5.
Subtitle Adjust (2D to 3D Conversion is On)
Use this function to automatically identify subtitles during 2D to 3D conversion. There may be instances where
automatic identification does not work, or video...

9.0  INSTALLATION SETTINGS
32 R699820 - Yunzi Series User Manual
The pixel adjustment is extremely fine: each color can be adjust within 1/16 pixel steps on 121 individual adjustment
zones.
Adjust
Enable the pixel adjustment On or Off.
Adjust Area
Whole: the entire screen is selected for adjustment.
Zone: the screen is divided into 121 adjustment zones.
Adjust Color
Select the color to adjust: Red or Blue.
Adjust Pattern Color
Select a pattern to help the pixel alignment. Settings: White or...

9.0  INSTALLATION SETTINGS
R699820 - Yunzi Series User Manual 33 
9.5 Pincushion
Compensate distortions that may appear with curved screens or anamorphic setups.
9.6 Anamorphic
•Off: No modification to original picture.
•Mode A: The picture is vertically stretched to fit an installation with anamorphic lens. A cinemascope picture is
stretched to completely fill the panels without black bands, using the optimum resolution and brightness.
Anamorphic Mode A.
•Mode B: This setting squeezes horizontally the...

10.0  DISPLAY SETUP SETTINGS
34 R699820 - Yunzi Series User Manual
9.8 Environment Setting
To finely tune the picture setting, you may change the environment settings so that they match your installation:
•Screen size: diagonal size in inches set this setting between 60” and 200”.
•Viewing distance is the distance to the screen of the nearest seat in meters, set it between 1m and 10m.
•Wall color, select “Dark” if the walls are black or similar, for any lighter shades select “Light”.
10.0DISPLAY SETUP...

12.0  INFORMATION MENU
R699820 - Yunzi Series User Manual 35 
11.4 ECO Mode
This setting when set to On will minimizes the power consumption in the Standby Mode. Additionally, this product
will automatically switch Off whenever the input signal is interrupted for 30min.
11.5 Communication Terminal
Sets the input to which the control device is connected to. It is not possible to use both RS-232C and LAN inputs at
the same time. Settings: RS-232C, LAN.
11.6 Network
When the Communication Terminal selected...

13.0  CINEMASCOPE SETUPS
36 R699820 - Yunzi Series User Manual
13.0CINEMASCOPE SETUPS
13.1 Lens Zoom or Theater System Kit
The Yunzi Series centralizes the controls and automation commands for a unique, versatile and unexpectedly
simple to operate 2.35:1 theatre experience using Lens Zoom or Anamorphic Lens.
•Up to 10 lens position memories
•Integrated Constant Image Width (CIW) scaler with anamorphic mode A and mode B.
•Dedicated commands to control the Theater System Kit and picture size on a 2.35:1...

14.0  MAINTENANCE
R699820 - Yunzi Series User Manual 37 
Video source is Cinemascope: set [Anamo]rphic to Mode A
Select Anamorphic mode A for this input in the menu Input “Installation ⇒⇒ ⇒ ⇒
 Anamorphic ⇒⇒ ⇒ ⇒
 Mode A”.
[Anamo]rphic modes
When you press sequentially the [Anamo]rphic button, you change the mode from OFF, Mode A and Mode B.
•Mode A is intended to be used with an anamorphic lens to watch 2.35:1 content on a 2.35:1 screen.
•Mode B is intended to be used to quickly switch to 16:9 content...

14.0  MAINTENANCE
38 R699820 - Yunzi Series User Manual
Light-source Lamp and Lamp Usage Time
The life of light-source lamps used for this unit is about 4000 hours when running this unit in low lamp mode.
•When the lamp power is set to Low, the lamp life is approximately 4000 hours. This average lamp life is not
guaranteed and may not reach 4000 hours depending on the operating conditions.
Deterioration progresses rapidly when the remaining lamp usage time is short. Get ready or replace with a new
lamp...

14.0  MAINTENANCE
R699820 - Yunzi Series User Manual 39 
a) Turn On the unit.
b) Browse into the menu Function => Reset Lamp Time.
c) Confirm time reset.
Alternative method in standby mode, using the remote control. 
a) Plug this unit to Main power.
b) When the projector is in standby mode (red STANDBY/ON led), use the remote control and press sequentially
the [BACK] - [OK] - [HIDE] within 1 second interval then [DOWN] for at least 2 seconds.
c) The sequence is successful if the STANDBY/ON and LAMP leds...

15.0  MISCELLANEOUS
40 R699820 - Yunzi Series User Manual
15.0MISCELLANEOUS
15.1 RS-232C protocol
Serial communication specifications
Control of this unit is possible using a computer or automation device connected with a RS-232 cross cable (female
- female D-sub 9 pins cable) or LAN/ RJ-45 cable. Communication specifications for this unit are as follows:
ID#
Operating LED
DescriptionSTANDBY / 
ONLAMP
orange LEDWARNING
red LEDBlinking
5/6-orange--
Lamp time has reached 2900 hours and/or 
prepare to replace...