Dream Vision Starlight 3 User Manual

7.0  ANAMORPHIC LENS
R699782 - Starlight 3 User Manual31 
7.0 ANAMORPHIC LENS
7.1 Optional 2.35 Wide System for Starlight and 2.35 THEATRE System
The Starlight 3 centralizes the controls and automation commands for both the 2.35 Wide System for Starlight and
the 2.35 THEATRE System for a unique, versatile and unexpectedly simple to operate 2.35:1 theatre experience
using an Anamorphic Lens.
•Integrated Constant Image Width scaler.
•Dedicated menu to program the 12V Trigger output.
7.2 Using the Remote...

7.0  ANAMORPHIC LENS
32R699782 - Starlight 3 User Manual
7.3 2.35 Wide System for Starlight options
Select a 16:9 input: Aspect Ratio to “4:3”
When you select a 16:9 input, choose the “4:3” aspect mode to obtain a geometrically correct picture in your screen.
•Select “4:3” for this input into the menu “Input Signal ⇒⇒ ⇒ ⇒
 Aspect Ratio ⇒⇒ ⇒ ⇒
 “4:3””.
Cinemascope input: set “V-Stretch -> On”
When selecting a widescreen input (2.35:1, 2.37:1 or 2.40:1), the original aspect ratio of the source is larger...

7.0  ANAMORPHIC LENS
R699782 - Starlight 3 User Manual33 
Configure Function Menu ⇒⇒ ⇒ ⇒ Trigger to “On (V-Stretch)”
The “Function ⇒⇒ ⇒ ⇒
 Trigger” menu determines the 12V Trigger output located in the panel input of the Starlight 3 this is
a global parameter (for all inputs):
•OFF: the 12V Trigger is always switched Off.
•ON (Power): the 12V Trigger is switched On when the projector is running, Off if the projector is in standby
Mode.
•ON (V-Stretch): the Trigger is Off when the V-Stretch value is Off....

8.0  MAINTENANCE
34R699782 - Starlight 3 User Manual
8.0 MAINTENANCE
8.1 Clean Dirt on the Cabinet
Always use a soft cloth. In case of heavy soiling, soak a cloth in neutral detergent diluted with water, wring dry and
wipe, followed by wiping again using a dry cloth.
Caution
Pay attention to the following as the cabinet may deteriorate in condition, get damaged or paint may come
off.
•Do not wipe with a stiff cloth.
•Do not wipe with force.
•Do not wipe with thinner or benzene.
•Do not spray volatile...

8.0  MAINTENANCE
R699782 - Starlight 3 User Manual35 
•Tighten the screws of the lamp unit.
•Attach the lamp cover and fasten the two lamp trap screws.
Resetting Lamp Time
After installing a new lamp, reset the lamp time into the OSD menu. 
a) Insert plug into the power outlet
b) When the projector is in standby mode (red STANDBY/ON led), use the remote control and press sequentially
the [BACK] - [OK] - [HIDE] within 1 second interval then [DOWN] for at least 2 seconds.
c) The sequence is successful if...

8.0  MAINTENANCE
36R699782 - Starlight 3 User Manual
Warning Led
ID#
Operating LED
DescriptionSTANDBY / 
ONLAMP
orange LEDWARNING
red LEDBlinking
1red---Unit is in standby mode
2green---Unit is in operate mode (during projection)
3blinking 
green--Ye s
Unit is in operate mode, but HIDE is ON. 
Press again on HIDE button to obtain a 
picture.
4blinking red--Ye sUnit is in cooldown mode. (switching off)
5/6-orange--
Lamp time has reached 2900 hours and/or 
prepare to replace the lamp before 3000 
hours.
7...

9.0  MISCELLANEOUS
R699782 - Starlight 3 User Manual37 
9.0 MISCELLANEOUS
9.1 RS-232 input and IR Codes
Communication Specifications
Control of this unit is possible using a computer or automation device connected with a RS-232 cross cable (female
- female D-sub 9 pins cable). Communication specifications for this unit are as follows:
Pin assignation
Command Format
When sending a command to this unit, use the following data format:
Available Operating commands
Baud Rate 19200 bps
Data Format Binary
Mode...

9.0  MISCELLANEOUS
38R699782 - Starlight 3 User Manual
RCU Commands and sending them through RS-232
Switch Input49h 50h30hSwitch active input to S-Video
31hSwitch active input to Video
32hSwitch active input to Component
33hSwitch active input to VGA
36hSwitch active input to HDMI 1
37hSwitch active input to HDMI 2
2BhSwitch to next input
2DhSwitch to previous input
Test Pattern54h 53h30hTest Patterns  Off.
31hColour bars
36hStair Step (black & white)
37hStair Step (red)
38hStair Step (green)
39hStair...

9.0  MISCELLANEOUS
R699782 - Starlight 3 User Manual39 
Picture Mode52h 43h37h 33h 36h 34hDay profile (require Expert Cal. ON)
37h 33h 36h 35hNight profile (require Expert Cal. ON)
37h 33h 36h 36hCinema 3
37h 33h 36h 37hStage
37h 33h 36h 38hCinema 2
37h 33h 36h 39hCinema 1
37h 33h 36h 41hNatural
37h 33h 36h 42hDynamic
37h 33h 36h 43hUser 1
37h 33h 36h 44hUser 2
37h 33h 36h 46hTH-PRO
Picture Adjust52h 43h37h 33h 37h 32hToggle Picture Adj. menu.
Gamma52h 43h37h 33h 37h 35hToggle Gamma function menu.
37h 33h...

9.0  MISCELLANEOUS
40R699782 - Starlight 3 User Manual
Lens Control
Examples
Available Reference and Response commands
A reference command ask the projector about its status. The projector send back an ACK command together with a
Response command.
Lens Aperture52h 43h37h 33h 32h 30hToggle the Lens Aperture setting menu.
37h 33h 32h 38hSet Lens Aperture to setting “1”
37h 33h 32h 39hSet Lens Aperture to settign “2”
37h 33h 32h 40hSet Lens Aperture to setting “3”
Lens Aperture +52h 43h37h 33h 31h...