Dream Vision Dreambee User Manual

3.0  INSTALLATION GUIDELINES
R699740 - DreamBee User Manual 11 
3.3 Air-Flow and Space Requirements
This unit can be installed in table position. Make sure that the unit is installed within the space requirements
described below.
•A: Air inlets
•B : Air outlets
Air flow
Space requirements
A A
A
B
B
A
A
B
100 mm
150 mm
150 mm100 mm
150 mm
150 mm 

3.0  INSTALLATION GUIDELINES
12R699740 - DreamBee User Manual
3.4 Ceiling mounting the unit
When mounting of this unit is required, do so by removing the 4 feet and make use of the 4 screw holes (M5
screws) at the bottom of this unit. Allow sufficient space around the air inlets to avoid blocking them
.
Precautions for Ceiling-mount
•To ceiling-mount this unit, special expertise and techniques are necessary.
Be sure to ask your dealer or specialist to perform mounting.
• Do not mount at places that may...

3.0  INSTALLATION GUIDELINES
R699740 - DreamBee User Manual 13 
Vertical and Horizontal Offset Setting
The optimum image can be obtained when the centre of this projector’s lens and the screen are placed
perpendicular to each other. Take note of the projection angle when placing them. Failing to do so may give rise to
trapezoidal distortion of the projected image.
This unit comes with a optical shift that features vertical and horizontal adjustment of the projection screen position.
Adjust the picture...

3.0  INSTALLATION GUIDELINES
14R699740 - DreamBee User Manual
3.5.0.1 Adjust the picture position vertically
The DreamBee projector has two dials to center the picture to the screen vertically and horizontally. Refer to the
picture below to locate the dials.
The Vertical and Horizontal shift dials are located at the bottom of the unit.
Turn clockwise to shift the picture on the screen downward.
Turn anti-clockwise to shift the picture on the screen upward.
Ve rtical Shift Dial
(-80% to +80%)
Horizontal...

3.0  INSTALLATION GUIDELINES
R699740 - DreamBee User Manual 15 
3.5.0.2 Adjust the picture position horizontally
Turn clockwise to shift right the picture on the screen.
Turn anti-clockwise to shift left the picture on the screen. 

4.0  REMOTE CONTROL UNIT (RCU)
16R699740 - DreamBee User Manual
4.0 REMOTE CONTROL UNIT (RCU)
4.1 General view
4.2 Loading and replacing batteries
•Push the cover tab with the fingernail a little backwards and pull upwards the cover top.
Slide the cover forward to remove.
LIGHT
TEST EXIT
SHARP
-
SHARP+
USER2
N
COLOR
TEMP
GAMMA
USER
3
D
COLOR-
COLOR+
USER1
C
CONTRAST
BRIGHT
HIDE INFO
MENU
ENTER
CINEMA NATURAL DYNAMIC HDMI 1
HDMI 2
S-VIDEO COMP
VIDEO ASPECT
OFF  ........    OPERATE    .........   ONPower...

4.0  REMOTE CONTROL UNIT (RCU)
R699740 - DreamBee User Manual 17 
•Push the battery body towards the spring and lift up to remove.
Insert two AAA size batteries, making sure the polarities match the + and - marks inside the battery
compartment.
• Insert the lower tab of the battery cover in the gap at the bottom of the remote control, and press the cover until
it clicks in place.
4.3 How to use the remote control unit
The operable distance of the remote control unit is about 7m for direct reception and...

5.0  GETTING STARTED
18R699740 - DreamBee User Manual
5.0 GETTING STARTED
5.1 General View
Front side
•Air Outlet / Inlet: see “Air-Flow and Space Requirements”,  page 11.
•F ocus and Zoom Adjust: see “Focus and Zoom Adjust”,  page 19.
• This unit comes with buffer material that cushions the lens during transport. Remove the material before use.
Rear side
•Input Panel: see page 22.
• Main Power: connect the power cord. See below.
• Operating LEDs: see page 20 for more details.
• Operating and Navigation...

5.0  GETTING STARTED
R699740 - DreamBee User Manual 19 
5.3 Focus and Zoom Adjust
CAUTION AGAINST FIRE AND ELECTRIC SHOCK
Since the power consumption of this unit is high, insert the power plug directly into a wall outlet.
When not using devices, remove the power plug from the wall outlet.
Do not use power cords for connection other than specified.
Do not use a power voltage different from that which is indicated.
Do not cut, tear or modify the power cords. Also, do not place a heavy object on, heat or...

5.0  GETTING STARTED
20R699740 - DreamBee User Manual
5.4 Operating LEDs
Operating LED
Description
WARNINGLAMPSTANDBY/ON
OffOffLight On (red)Unit is in standby mode
OffOffLight On (green)Unit is in operate mode (during projection)
OffOffBlinking (green)The video image is temporarily cleared upon 
pressing the [HIDE] button during projection.
OffOffBlinking (red)Unit is in CooL Down* mode
(when cooling lamp)
Light On (red)Off-An error occurred during operation, the projector 
will enter Cool Down* mode....