Digital Projection Titan Pro Series III User Guides

							
Digital Projection Titan Pro series III  A TOUR OF THE MENUS  Operating Guide
Page Op_21Rev A   May 2012
Information Menu
The sub-menus give information about lamp operating times, software and \
hardware configurations, the input source and Digital Projection.
Projector
Source
Digital Projection
Notes
 See also Using the Menus, earlier 
in this guide and Menu Map, later in 
this guide.
Main MenuInformationProjector
 The number of lamps is dependent 
on the projector model.
Main MenuInformationSource
Main MenuInformationDigital Projection 
						

							
Digital Projection Titan Pro series III  MENU MAP  Operating Guide
Page Op_22Rev A   May 2012
Menu Map
Main Menu Sub Menus
Input Selection
CVBS 1, CVBS 2, S-Video, Component, VGA, 3G-SDI, DVI, HDMI, Test Pattern, Main/DVI, Sub/HDMI, Dual Pipe
Test Pattern
Grey V Bars, Grey H Bars, Aspect Test, Alignment Grid, Warp Adjust, SMPTE, Chequerboard, White Field, Black 
Field
Global Settings
Projector
Orientation  Desktop Front, Ceiling Front, Desktop, Rear, Ceiling Rear
Latency  Minimal, Best Video
Configuration  PIP, Edge Blend
Picture
Colour Mode  Peak, HDTV, SDTV, Colour Temperature, User 1, User 2
Gamma  1.0 to 2.8
Edge Blend
Array Width
Array Height
Array H Position
Array V Position
Blending  Off, On, Align Pattern
Segmentation  Off, On
Blend Width  Top, Bottom, Left, Right Blend Region, Apply Blend Regions
Black Level Uplift  Unblended Region, Upper Left, Upper Middle, etc, Apply Uplift
Reduce Black Level Uplift Width  Upper Left X, Y, Upper Right X, Y, etc, Apply Uplift
PIP
Option  Off, PIP, PAP, POP
Input  select from Group A or Group B
Size  Small, Medium, Large
Position  Top Left, Bottom Right etc
Custom H Position
Custom V Position
Notes
 Some of the information in this menu 
map is summarised. See the actual 
menu on the projector for full detail.
 Some menu options and controls 
may not be available due to settings 
in other menus. These will be 
greyed-out on the actual menu.
 Where it would be helpful, some 
menu options are described in more 
detail earlier in this operating guide.
 The Test Pattern menu is not 
available until Test Pattern is 
selected from the Input Selection 
drop-down list.
 There are two Picture menus – one 
in the Global Menu, and one in the 
Input Settings Menu.
 PIP and Edge Blend are mutually 
exclusive modes of operation. When 
in PIP mode, Edge Blend is not 
available, and vice versa. 
						

							
Digital Projection Titan Pro series III  MENU MAP  Operating Guide
Page Op_23Rev A   May 2012
Advanced Geometry
Mode  Off, Keystone, Cornerstone, Rotation, Warp
Warp Map  Off, 1 to 8
H Keystone
V Keystone
Pincushion/Barrel
Rotation
Cornerstone  Upper Left X, Y, Upper Right X, Y, etc
Input Configuration
DVI/HDMI   Boost DVI EQ, DVI/HDMI Colour Space, DVI/HDMI Range, DVI Port,  
Main/Sub Operation, Main/Sub Range
SDI  3G Level B Stream
Component  Colour Space, Sync Type
Lamp
Lamp Mode  Single lamp, Two lamps, Auto
Lamp Power   85 - 100%
Lens
Zoom In, Stop, Out,   Focus Near, Stop, Far
Calibrate Zoom, Calibrate Focus 
Nudge  Up, Down, Left, Right
On Screen Display
Language  US English, UK English
Timeout  Number of seconds, Infinite
Position  Centre, Top Left, Top Right, Bottom Left, Bottom Right
Messaging  Off, On
Network
DHCP  Off, On
IP Address
Subnet
DHCP Status  Information only:
IP Address
Subnet
MAC Address
Factory Defaults  Projector will ask for confirmation before restoring all settings to fac\
tory defaults.
Main Menu Sub Menus
Global Settings (continued)
Notes
 Some of the information in this menu 
map is summarised. See the actual 
menu on the projector for full detail.
 Some menu options and controls 
may not be available due to settings 
in other menus. These will be 
greyed-out on the actual menu.
 Where it would be helpful, some 
menu options are described in more 
detail earlier in this operating guide.
 The number of lamps is dependent 
on the projector model. Single lamp 
models will have no Lamp menu.
 Not all models have a lamp power 
setting.
 Each time a lens is fitted to 
the projector, the calibration 
procedure must be carried out.
  (Use this menu, or the remote 
control: see the Installation and 
Quick Start Guide)
 After calibrating the lens, you will 
need to re-adjust the Zoom and 
Focus.
 Do NOT do this unless you are 
sure that you want to restore 
ALL the current settings to their 
factory defaults. 
						

							
Digital Projection Titan Pro series III  MENU MAP  Operating Guide
Page Op_24Rev A   May 2012
Input Settings
Picture
Brightness
Contrast
Hue
Saturation
Black Level Offset  0 IRE
Video Filters   Sharpness, Detail, Luma Sharpness, Chrome Sharpness, Recursive Noise Red\
uction, 
Mosquito Noise Reduction, Cross Colour Suppression
VGA  Phase, Total H Samples, Auto setup
Colour Trim
RGB Lift and Gain
Geometry
Aspect Ratio  Source, Fill, Fill & Crop, Anamorphic, TheatreScope
H Position
V Position
Overscan
Pan/Scroll/Zoom  Enable, Disable, Global, Per Mode, Pan, Scroll, Zoom H, Aspect Lock, Zoom V, Reset
3D Settings
3D enable  Off, On
Source Dominance  Left, Right
Frame Multiplier  x1, x2, x3
3D Type  Auto, Sequential, Frame Packing, Top-and-Bottom, Side-by-Side (Half)
Glasses Settings  Dark Time, Sync Offset, Output Sync Polarity
System
Shutter  Open, Shutter Close, Power On, Power Off
Information
Projector  Information only:
Lamps  Hours, Strikes
Configuration  Scaler, Interface, Firmware, OSD, Lens, Hardware
Source  Information only:
Input
Standard
Digital Projection  Information only: Contact Information
Main Menu Sub MenusNotes
 Some of the information in this menu 
map is summarised. See the actual 
menu on the projector for full detail.
 Some menu options and controls 
may not be available due to settings 
in other menus. These will be 
greyed-out on the actual menu.
 Where it would be helpful, some 
menu options are described in more 
detail earlier in this operating guide.
 There are two Picture menus – one 
in the Global Menu, and one in the 
Input Settings Menu. 
						

							
Digital Projection Titan Pro series III  WEB CONFIGURATION UTILITY  Operating Guide
Page Op_25Rev A   May 2012
Web Configuration Utility
The LAN IP Address of the projector can be set by using the Network submenu, which can 
be found in the Global Settings menu.
Once the LAN IP Address has been set, it is possible to control all the functions availa\
ble on 
the OSD by using the embedded Web Configuration Utility:
Point your browser at the projector by typing the url 
http:// into the address bar, then press the Enter key.
The embedded webpage shown below right should appear.
Examples
The webpages mirror the OSD menus, as shown in the following examples:
The last 3 bytes of the projector’s 
MAC Address are shown in the Unit ID, 
00-26-AA in the example shown here.
The menu name is shown in orange, 
underlined text, as in the Main Menu 
shown here.
Drop-down lists are represented by 
similar drop-down lists, as in the Input 
Selection list shown here.
Sub-menus are represented by yellow 
underlined links, as in the Global 
Settings sub-menu shown here.
•
•
•
•
•
•
Notes
 For full details of how to use the 
menu system, see earlier in this 
Guide. 
						

							
Digital Projection Titan Pro series III  WEB CONFIGURATION UTILITY  Operating Guide
Page Op_26Rev A   May 2012
Sliders are represented by similar 
sliders, as in the Array Width slider 
shown here.
Items that are not available are shown 
greyed-out, as in the Array H Position 
slider and Blending list shown here.
To return from a sub-menu to the 
previous menu, click on the Back link at 
the bottom of the menu.
•
•
•
Notes
 For full details of how to use the 
menu system, see earlier in this 
Guide.
Commands are represented by Do it 
buttons, as in the Shutter Open 
command shown here.
•