Digital Projection Thunder 10000dsx User Manual

E – 35
Select either the RGB signal type or the Component signal type.
RGB ............. RGB signal
Component .. Composite signals such as Y/Cb/Cr, Y/Pb/Pr
NOTE: This feature is available on RGB 1 and 2 only.
Gain
This feature adjusts the input level of the signal. This must be done
to each color:R, G, and B.
Volume
This feature adjusts the volume of the audio output. Adjust the sound
corresponding to the slot.
Ref Adj
Keystone
This feature corrects the keystone (trapezoidal) distortion to make the
top...

E – 36
Lamp Mode
This feature allows the lamp power supply to operate under three set-
tings.
Maximum ..... This setting consumes maximum current from the AC input
and results in the most light output.
NOTE: The Maximum mode shortens the lamp life. Be sure to use this modeat temperature of 95˚ F (35˚C) or less.
Medium ....... This setting allows the lamp power supply to draw a medium
amount of current from the AC input source and allows for
medium power consumption.
Minimum ..... This setting consumes...

E – 37
5. To enable your setting, select Active on the Execute Switch.
6. Select OK and press the ENTER button on the remote control to complete
the setting.
NOTE: When On Timer is set and the projector is in the standby mode, the
Status indicator flashes green to show that On Timer program is active. The
projector must be in stand-by mode at the time of turning on. The preset
power-on time will be void if the cooling fan is working or an error occurs.
Unplugging the projector cancels your 1 Week...

E – 38
Setup
Enables you to set operating options.
Press OK to save your changes for all the features of Page1, Page2,
Page3, Page 4 and Page5.
[Page 1]
Orientation
This reorients your image for your type of projection.
The options are: desktop front projection, ceiling rear projection, desk-
top rear projection, and ceiling front projection.
Background
Use this feature to display a blue/ black screen or logo when no
signal is available. The default background is blue.
S-Video Mode Select
This feature is...

E – 39
Power Management
When this option is on and there is no RGB input for five minutes or
more, the projector will automatically turn itself off.
Power Off Confirmation
This option determines whether a confirmation dialog for turning off
the projector will appear or not.
Keystone Save
This option enables you to save your current keystone settings.
Saving your change once affects all sources. The changes are saved
when you turn off the projector.
Doubler (Video / S-Video Only)
This sets double speed...

E – 40
Source Information
Displays the status of the current signal. This dialog box has three pages.
Projector Information
Displays the information for your projector such as lamp usage, serial
number and version number etc..
Link Mode
Displaying Current Status of Link Mode
When selecting the tab Page 4 , you will get the following dialog
box.
Master ID .................... Indicates the Master projector
Status ......................... Indicates the status of the master projector
Connected PJ...

E – 41
Selecting a new signal that is close to one of the
listed signals in horizontal and vertical frequency
Selecting a new signal that is close to one of the listed signals in hori-
zontal and ver tical frequency may not display the image correctly be-
cause the new signal is considered as one of the registered signals
listed in the Entry List. (In this case the Auto Adjust feature may not
work correctly.)
To use both signals, use different input terminal (RGB 1, RGB 2 or RGB
3) respectively, or...

E – 42
6. SPECIFICATIONS
Optical
Panel *1DMDTM  .9 x 3
1280 x 1024 native resolution up to 1600 x 1200 with Advanced AccuBlendTM Technology
Lamp 2.0kW Bubble Type Short Arc Xenon
Built in: Overheat Protection
Lamp Over-Usage Protection
Light Output 9000 ANSI Lumens ±10%
Full Light Output at 200- 240V
Brightness Uniformity >80% edge to center
Contrast Ratio 800 : 1 Full On/Off
Lens Movement Motorized Horizontal and Vertical Lens Shift
Motorized Zoom and Focus
Built in Lens Shutter
Lens Options*
2TL-08SF...

E – 43
Contact Closure
Switcher (2) D-sub 15 pin In/Out
Addressable Remote Control (wired / wireless)
Power Requirement 200-240 VAC, 50/60Hz
Input Current 14 A
Power Consumption2.8 kW
BTU9554 per hour
Air flow 250 M
3 / hr
Air Inlet Underside front centre
Air Outlet Rear of left side (viewed from rear)
Mechanical
Installation Orientation:Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear
Stacking: Up to 2 projectors can be gravity stacked
Dimensions 26.8(W)40.0(D)16.5(H) with lens hood and feet...

E – 44
7. Optional Accessories
LensTL-08SF LA00111(Short Focal Lens 0.84) : 10kg
TL-1ZH LA00263 (Zoom Lens 1.5 - 2.5:1) : 5.5kg
TL-2Z LA00108 (Zoom Lens 2.5 - 4.0:1) : 4.5kg
TL-4Z LA00109 (Zoom Lens 4.0 - 7.0:1) : 4.5kg
Interface BoardSD-SDI BOARD LA00105
HD-SDI BOARD LA00204
Ceiling Mount Kit XL CMKIT LA00264
Switcher ISS-6020 Video/RGB Switcher
A Serial Digital Interface (SDI) board is optionally available.
SD-SDI BOARD
This board accepts the input of non-compressed signal sources such as commercial...