Digital Projection Showlite 6000gv Lcd Projector Users Manual

							6-3
6. Using the Projector in a Network
x Supported Projectors
The following Digital Projection projectors will be supported:
SHOWlite 6000gv/5000sx+
Operating Environment
Supported Equipment
CPU
Memory
Network Environment
(when used)
Supported OS
Resolution
Screen ColorsIBM PC/AT compatible computers
• CD-ROM drive a requirement (at time of installation)
Pentium MMX processor or higher a requirement
Pentium III 800 MHz or higher recommended
For Windows XP
• 128 MB or more a requirement
• 192 MB or more recommended
For other operating systems
• 64 MB or more a requirement
• 128 MB or more recommended
More memory may be necessary when other applications are run at the same time.
A LAN that supports TCP/IP or a wireless LAN environment is a requirement.
•For information on supported LAN cards, contact Digital Projection
•For wireless LAN connection, use Digital Projection optional wireless LAN card (001-723 or 001-
762 for France).
Windows 98
Windows 98 Second Edition
Windows Me
Windows 2000 Professional
Windows XP Home Edition
Windows XP Professional/Windows XP Tablet PC Edition
*Microsoft Internet Explorer 5.01 or higher is required for the aforementioned environments.
*Does not support Windows power-saving function.
1024 dots x 768 lines recommended
High Color (15 bit, 16 bit)
True Color (24 bit, 32 bit) 
						

							6-4
c Equipment Connections and Settings
When Using a Network Environment
What Can Be Accomplished
•Using Image Express Utility 1.0, the screen image displayed by the
personal computer can be sent to the projector and then projected to a
screen.
•Using Dynamic Image Utility 2.0, a picture or slide can be sent to the
projector and then projected to a screen.
•Using the projector control function of Dynamic Image Utility 2.0 allows
operations to be performed from the personal computer which include
switching the projector power on/off, signal selection, and adjustment
of the picture quality.
Equipment to Be Prepared• Projector (This unit)  • Personal computer (with LAN card)
• LAN cable (not supplied) or wireless LAN card (optional)
Settings at the Projector Side
Preparation:
(1) Connect a LAN cable (not supplied) to the LAN port (RJ-45) of the
projector.
(For the use of an optional wireless LAN card, insert the wireless LAN
card into the PC CARD slot 1 or 2 of the projector.)
(2) Switch on the projector power and project to the screen. (chapter 3)
(3) Switch to the advanced menu.
1. Press the MENU button.
The menu will be displayed.
2. Use the SELECT 
 button to align the cursor with [Projector Options],
then press the ENTER button.
The sub menu will be displayed.
3. Use the SELECT 
 button to align the cursor with [LAN Mode], then
press the ENTER button.
The LAN mode setting screen will be displayed.
4. Set the various items.
See Setting LAN Mode on page 8-19 for information about the vari-
ous items.
NOTE: When switching the power of the projector on/off with the projector control
function, please set [Projector Options] → [Setup] → [Page 4] → [Idle Mode] toOn.
Settings at the Personal Computer Side
Perform the regular LAN connections settings according to the
instruction manual of the LAN card (adapter).
There are no special settings to be made in the connections with
the projector.
When Making Connections with Serial Cable or USB Cable
What Can Be Accomplished
 • Using Dynamic Image Utility 2.0, a picture or slide can be sent to the
projector and then projected to a screen.
 • Using the projector control function of Dynamic Image Utility 2.0 allows
operations to be performed from the personal computer which include
switching the projector power on/off, signal selection, and adjustment
of the picture quality.
[For Connections with USB Cable]
Equipment to Be Prepared
•Projector (This unit)
•Personal computer
•USB cable (included with the projector)
Connection at the Projector Side
Plug the B type connector of the USB cable to the USB port [PC]
(type B).
NOTE: When switching the power of the projector on/off with the projector control
function, please set [Projector Options] → [Setup] → [Page 4] → [Idle Mode] to“On”.
Connection at the Personal Computer Side
Plug the A type connector of the USB cable to the USB port [PC]
(type A).
[For Connections with Serial Cable]
Equipment to Be Prepared
•Projector (This unit)
•Personal computer
•Serial cable (A commercially available RS-232C cross cable for
SHOWlite 6000gv/5000sx
+)
Connection at the Projector Side
Plug the serial cable into the PC CONTROL connector. (“Termi-
nal Panel Features” and “PC Control Connector” on pages 1-9
and 10-10)
Connection at the Personal Computer Side
Plug the serial cable into the (RS-232C) serial connector.
6. Using the Projector in a Network 
						

							6-5
6. Using the Projector in a Network
v Software Installation
NOTE
•Windows 98 operations will be described in examples given here.
•When using Windows 2000, please perform software installation/uninstalling with
Administrators authority. When using Windows XP, perform with Computer
Administrator authority.
Installation
Dynamic Image Utility 2.0, Viewer PPT Converter 2.0, and Im-
age Express Utility 1.0 will all be installed together. The various
programs cannot be installed individually.
Preparation:
Start Windows.
If Windows has already been started, please exit all running ap-
plication software. The installation may not be completed prop-
erly unless all software has been exited.
1. Place the supplied CD-ROM in the CD-ROM drive.
The Welcome screen will appear.
Reference
Should the Welcome screen not appear...
1) Click [Start].
2) Click [Run (R)]. The [Run] screen will appear.
3) Enter the CD-ROM drive name (e.g., Q: \) and then SETUP.EXE
to [Open (O)].
4) Click [OK]. The Welcome screen will appear.
2. Click [Next >] at the Welcome screen.
The End User License Agreement screen will appear.
•Please carefully read the contents of the End User License Agree-
ment.
3. If you agree, click [Yes].
•If you do not agree, please click [No] and exit the installer.
4. Now, follow the operations described in the screen messages.
•Please remove the CD-ROM from the CD-ROM drive when the
installation is completed.
Reference
•To cancel the installation of the supplied software part way through
the installation, click [Cancel] and follow the instructions of the dia-
log box.
Uninstalling
Dynamic Image Utility 2.0, Viewer PPT Converter 2.0, and Im-
age Express Utility 1.0 will all be uninstalled together. The vari-
ous programs cannot be uninstalled individually.
1. Click [Start].
2. Click [Settings] R [Control Panel].
The Control Panel screen will be displayed.
3. Double click [Add/Remove Programs].
The Add/Remove Programs Properties screen will appear.
4. Click Projector User Supportware from the list.
5. Click [Add/Remove. . . ].
The Confirm File Deletion screen will appear.
6. Check the message and click [Yes].7. Now, follow the operations described in the screen messages.
When the uninstall procedure is completed, there will be a return to the
Add/Remove Programs Properties screen.
8. Click [OK].
There will be a return to the Control Panel screen 
						

							6-6
b Starting/Exiting the Software
Dynamic Image Utility 2.0
Start the Software
Preparation:
Install the software on the personal computer from the supplied
CD-ROM. (Page 6-6)
The software cannot be started from the supplied CD-ROM.
From the [Start] menu click [Program] → [Projector User
Supportware] → [Dynamic Image Utility 2.0].
Dynamic Image Utility 2.0 will start.
Reference
•By selecting a PowerPoint file with Dynamic Image Utility 2.0 and click-
ing [Tools] → [Converting PowerPoint file], the function equivalent to
Viewer PPT Converter 2.0 can be executed.
•Image Express Utility 1.0 can be started by clicking [Tools] → [Image
Express Utility 1.0 Start] of Dynamic Image Utility 2.0.
Display Help
Preparation:
Please start Dynamic Image Utility 2.0.
1. Click [Help].
The [Help] menu will appear.
2. Click [Help].
The [Help] screen will appear.
Exit the Software1. Click [File].
The [File] menu will appear.
2. Click [Exit].
Dynamic Image Utility 2.0 will close.
Viewer PPT Converter 2.0
Start the Software
Preparation:
(1) Check that Microsoft PowerPoint has been installed. Viewer PPT Con-
verter 2.0 cannot be used unless PowerPoint has been installed.
(2) Install the software on the personal computer from the supplied CD-
ROM. (Page 6-6)
The software cannot be started from the supplied CD-ROM.
1. From the [Start] menu click [Program] → [Projector User Supportware]→ [Viewer PPT Converter 2.0].
Dynamic Image Utility 2.0 will start.
Reference
•A function equivalent to Viewer PPT Converter 2.0 can also be
executed from the Dynamic Image Utility 2.0 [Tools] 
→ [Converting
PowerPoint file] menu.
•Viewer PPT Converter 2.0 can also be started from the Microsoft
PowerPoint 2000/2002 [Tools] 
→ [Projector User Supportware] →[Output Viewer] menu.
Display Help
Preparation:
Please start Viewer PPT Converter 2.0.
1. Click [Help].
The [Help] menu will appear.
Exit the Software1. Click [Exit].
Viewer PPT Converter 2.0 will close.
Image Express Utility 1.0
Start the Software
Preparation:
Install the software on the personal computer from the supplied
CD-ROM. (Page 6-6)
The software cannot be started from the supplied CD-ROM.
1. From the [Start] menu click [Program] → [Projector User Supportware]→ [Image Express Utility 1.0].
Image Express Utility 1.0 will start.
Reference
•Image Express Utility 1.0 can also be started from the [Tools] R
[Image Express Utility 1.0 Start] menu of Dynamic Image Utility
2.0.
Display Help
Preparation:
Please start Image Express Utility 1.0.
1. Click the [] or [] icon of the Windows screen task tray.
The main menu of Image Express Utility 1.0 will appear.
2. Click [Help] .
The Help screen will appear.
Exit the Software
1. Click the [] or [] icon of the Windows screen task tray.
The main menu of Image Express Utility 1.0 will appear.
2. Click [Exit].
Image Express Utility 1.0 will close.
6. Using the Projector in a Network 
						

							6-7
6. Using the Projector in a Network
n Troubleshooting
In this section, the software names have been abbreviated as follows:
Dynamic Image Utility 2.0 to DIU 2.0, Viewer PPT Converter 2.0 to PPTC 2.0, and Image Express Utility 1.0 to IEU 1.0.
 Installation does not complete normally.
Check PointsCountermeasures
When using Windows 2000, did you log on with Administra-
tors authority? When using Windows XP, did you log on with
Computer Administrator authority?When using Windows 2000 or Windows XP, log on with the
authority described at the left and then install.
Has Microsoft PowerPoint 2000/2002 been installed on the
personal computer to which this projector software is being
installed?
When this projector software is installed on a personal
computer that does not have PowerPoint 2000/2002 installed,
a message to the effect of Error in the automatic registration of
PPTViewer2.dll will appear part way through the installation.When the message described at the left appears part way
through the installation, add-in registration will not be made to
PowerPoint; however, the installation of this projector software
will be completed normally.
To have add-in registration made to PowerPoint, please install
this projector software to a personal computer on which
PowerPoint 2000/2002 has been installed.
 Viewer PPT Converter 2.0 does not function. (PPTC 2.0)
Check PointsCountermeasures
Has Microsoft PowerPoint been installed on the personal
computer?Install PowerPoint on the personal computer. Or, install Viewer
PPT Converter 2.0 on a personal computer on which
PowerPoint has been installed.
 When using the projector control function, the projector power does not switch on. (DIU 2.0)
Check PointsCountermeasures
Are the personal computer and the projector connected by a
serial cable?
Or, are the personal computer and the projector connected by
a LAN?Connect the personal computer and the projector with an serial
cable or USB cable.
Or, check the LAN port (RJ-45) of the projector. Purchase the
optional wireless LAN card for wireless LAN connection.
When the personal computer and the projector are connected
with a LAN, is the projector in the idle mode?In the [Projector Options]
[Setup] menu of the projector, place
checkmark in “Idle Mode”. Connect a power cable to the
power outlet and set the main power switch to I (On).
 You want to delete the PowerPoint add-in registration. (PPTC 2.0)
Check PointsCountermeasures
Installing this projector software when Microsoft PowerPoint
2000/2002 has already been installed on the personal
computer, will result in the automatic registration of the add-in
to PowerPoint.Please see the PowerPoint Help function for the method of
deleting PowerPoint add-in registrations.
The PowerPoint add-in registration will not be deleted even
when this projector software is uninstalled. 
						

							6-8
 Projection to the screen is not possible when using the LAN environment. (DIU 2.0, IEU 1.0)
Check PointsCountermeasures
Have LAN cards (i.e., adapters) been put into both the personal
computer and the projector?Put LAN cards (i.e., adapters) into both the personal computer
and the projector.
Have the LAN settings (for both the personal computer and the
projector) been completed?Perform the LAN settings for both the personal computer and
the projector.
Are a wired LAN and a wireless LAN being used simultaneously
with the same personal computer?Please cancel either one of the LAN connections. When a built-
in type is used, set it to not used under Properties.
Image Express Utility 1.0 does not support the following:
(1) Software using Direct X
(2) MS-DOS screens
(3) Microsoft Office assistant
(4) IME
(5) Moving pictures
 Operation of this projector software becomes unstable. (DIU 2.0, IEU 1.0)
Check PointsCountermeasures
When the network settings of the projector or personal
computer are changed while this projector software (i.e.,
Dynamic Image Utility 2.0 or Image Express Utility 1.0) is
starting or running, the operation of the projector software may
become unstable.Please restart the projector and the personal computer. When
changes are to be made to the network settings, exit the
projector software before making the changes.
An application error occurs under Image Express Utility 1.0
when the screen resolution is changed during Continuous
Transmit.When changes are to be made to the screen resolution, exit
Image Express Utility 1.0 before making the changes.
 The colors become strange when Windows is set to 256 colors. (IEU 1.0)
Check PointsCountermeasures
Image Express Utility 1.0 does not support 256 colors. Please set the Windows number of colors setting to High Color
(15 bit) or higher.
6. Using the Projector in a Network 
						

							6-9
6. Using the Projector in a Network
 The projector cannot be found with General search. (IEU 1.0)
Check Points Countermeasures
Are the wireless LAN settings appropriate?
Are the channel numbers for the personal computer and the
projector set to the same number?
When WEP (encryption) has been set, has the same value been
set for both the personal computer and the projector?Please check the access points, the personal computer setting
values and the projector [LAN Mode] setting values.
When using the infrastructure or 802.11 Ad Hoc, please set to
the same character string since SSID distinguishes between
upper and lower case characters.
Are radio communication conditions satisfactory? Check whether there are obstacles located between the
access point and the personal computer. Try moving the
personal computer closer to the access point.
Are the TCP/IP settings (e.g., IP address, sub net mask, etc.) of
the personal computer and the projector correct?Check whether the network settings are within the same
segment.
Are more than one network interface cards (NIC) being used
with the same computer?Set only the network interface card (NIC) that is connected to
the projector to Valid.
For a network card that is not connected to the projector, click
the network card name under Control Panel 
 System 

Device Manager 
 Network Adapter and then click
[Properties (R)] and set the device usage to Not used.
 Sometimes it takes a long time for screen transmission from the personal computer to the
projector. (IEU 1.0)
Check PointsCountermeasures
•Transmission time may be long depending on the image
pattern.
•When screens are sent to multiple projectors simultaneously,
a larger number of projectors will result in longer transmission
times.
•The transmission time may vary depending on the network
environment.
•The transmission time may vary depending on the perfor-
mance of the personal computer as well as other application
software that is running at the same time.
Transmission time will be longer when the resolution of the
personal computer and that of the projector differ since there
will be an increase in resolution conversion processing.We recommend that the resolution of the personal computer
and that of the projector be set to the same setting value
(except SHOWlite 5000sx
+).
The resolution of SHOWlite 6000gv, is 1024 x 768 dots.
Select the resolution to 1024 x 768 on your PC for sending an
image to SHOWlite 5000sx
+.
 Cannot follow the screen switching processing of the PowerPoint slide show, etc. (IEU 1.0)
Check PointsCountermeasures
Smooth screen switching processing or animation effects
cannot be followed because in Image Express Utility 1.0, the
screen condition of the personal computer is sent to the
projector at a fixed time interval.Use the software with  the PowerPoint screen switching
effects, animation effects, and other settings set to None. 
						

							6-10
6. Using the Projector in a Network 
						

							7-1
7
Setting Up for Double Stacking in
Link Mode
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
z Stacking and Connecting the Projectors .................. 7-2
x 
Adjusting and Registering Signals to Be Projected ...........7-5
c Adjusting the Lens Shift, Zoom and Focus to Clearly
Display all projected patterns ................................ 7-5
v Link Mode Setting ..................................................... 7-5
b List of Menu Items Available in Link Mode ................ 7-6 
						

							7-2
7. Setting Up for Double Stacking in Link Mode
z Stacking and Connecting the Projectors
Master projector
Slave projector
NOTE: Up to two units can be gravity stacked without external support. In some
cases, however, two images will not align on the screen correctly. This will become
more apparent when displaying small text and detailed graphics.
NOTE: Do not stack both the SHOWlite 6000gv and 5000sx+ projectors together.
CAUTION: To prevent the projectors from falling, install them in a place and fasten them in a
way with sufficient strength to support the two projectors. The projector with a lens weighs 21
kg/46.3 lbs.
z-1. Assigning Projector IDs
You can operate multiple projectors with the same remote con-
trol.
To  do so:
z-1-1. Select [Projector Options] → [Link Mode] → [Settings] →
[Projector ID] a-nd assign an ID number to each projector. See
also page 8-18.
z-1-2. Select the same communication speed for both the pro-
jector.
NOTE: Do not turn on [Master] or [Slave] at this time.
z-1-3. On the remote control specify the ID number of the pro-
jector to be adjusted. Press and hold the CTL and press
MENU (ADDRESS) button to enter the ID number.
You can operate the projector assigned the same ID number
as the remote control.
NOTE: Specifying None for projector ID allows you to operate multiple projectors
concurrently. However, some projectors may not synchronize to the other projec-
tors.