Digital Projection Showlite 5000sx+ Lcd Projector Users Manual

							4-3
v Using the USB Mouse
Using a commercially available USB mouse gives you smooth operation.
NOTE: There may be some brands of USB mouse that the projector does not sup-port.
Operate the Projector Menus using the USB mouse
Mouse CursorWhen connecting a USB mouse to the projector, you get a
mouse cursor on the screen.
Unless you use your USB mouse within 10 seconds, the mouse
cursor disappears.
Menu DisplayClicking with a mouse button displays the menu.
Clicking  displays the pull-down menu. To close the menu,
click anywhere in the background.
Adjusting and Setting DisplayYou can select a menu item and click with a mouse button to
make adjustments and setting.
ExamplesClick (or press and hold) the mouse button  or  to adjust
the brightness. Or click and drag the mouse button on the slide
bar horizontally to adjust it.
To save the adjustments, click 
. This closes the menu. If you
click anywhere in the background while displaying an adjust-
ment and setting menu or dialog box, you will go to the main
menu after clicking with the mouse.
Clicking 
 displays help.
Using the Middle Button/Wheel on a Mouse (when avail-
able)
The projector supports the middle button/wheel on a mouse. With
the middle button/wheel you can use a scroll bar or click the middle
button/wheel to display or hide the Chalkboard toolbar.
b Using the USB HUB Function
When using the projector with a PC via the supplied USB cable, both the
USB port(type A) on the projector can be connected to a USB-supported
scanner or other USB-supported device. (USB Hub Function)
Example: When connecting a PC and a scanner to each USB port respec-
tively
An example of how a scanned image is projected
1. Install the Dynamic Image Utility on your PC.
NOTE: The Dynamic Image Utility is contained on the supplied CD-ROM. See“6- b Software Installation” for the installation procedure.
2. Use your scanner to scan an image.
NOTE: A scanner driver must be installed on your PC before use.
3. Load the scanned image on your PC using the Dynamic Image Utility.
4. Transmit the scanned image from your PC to the projector via the USB
cable and project the image on the screen.
NOTE:
•The USB HUB function is effective only when “Auto” is selected in Operation
Mode Select.
•The PCs using the USB Host Controller may not be available.
•When connecting a USB hub to the USB port (type B) on the projector, be sure
to use a USB hub capable of supplying 500mA per port of downstream current.
IN
USB (MOUSE/HUB)USB (PC)PC CARD2
1
PC CONTROL
IN OUT
OUT SC TRIGGER REMOTE 2REMOTE 1LAN
AC IN 
AUDIO
AUDIOAUDIO OUT
R
R/Cr
G/Y
B/Cb
V
H/HV
RL/MONO
RL/MONORL/MONOL/MONO
OPTION 1 OPTION 2DVI
RGB OUT
RGB 1
RGB 2
VIDEOS-VIDEO
USB(MOUSE/HUB)
4. Convenient Features
IN
USB (MOUSE/HUB)USB (PC)PC CARD2
1
PC CONTROL
IN OUT
OUT SC TRIGGER REMOTE 2REMOTE 1LAN
AC IN 
AUDIO
AUDIOAUDIO OUT
R
R/Cr
G/Y
B/Cb
V
H/HV
RL/MONO
RL/MONORL/MONOL/MONO
OPTION 1 OPTION 2DVI
RGB OUT
RGB 1
RGB 2
VIDEOS-VIDEO
USB(PC)
Operate the PC mouse using the USB mouse
NOTE: You can select the operation mode of the USB mouse connected to the USBport of the projector.
INUSB (MOUSE/HUB)USB (PC)PC CARD2
1
PC CONTROL
IN OUT
OUT SC TRIGGER REMOTE 2REMOTE 1LAN
AC IN 
AUDIO
AUDIOAUDIO OUTR
R/Cr
G/Y
B/Cb
V
H/HV
RL/MONO
RL/MONORL/MONOL/MONO
OPTION 1 OPTION 2DVI
RGB OUT
RGB 1RGB 2VIDEOS-VIDEO
USB(
PC)
USB(
MOUSE/HUB) 
						

							4-4
n Changing Background Logo
You can change the default background logo using the PC Card Files
feature.
NOTE: File size must be 256KB or less. Other file formats than JPEG and BMP arenot available.
1. From the menu, select [Tools] 
→ [PC Card Files] to display a list of all
the files stored in the PC card so that you can select a file you want to
use as a background logo.
2. The Logo button allows you to select a background logo from graphic
files on a PC card and change to it as the background logo.
3. Use the SELECT 

 or  button to select a JPEG or BMP file for your
background logo.
4. Use the SELECT 
 and then  button to select Logo.
5. Press the ENTER button on the remote control or the cabinet. You
will get the confirmation dialog box.
6. Select OK and press the ENTER button. This completes changing
a logo for the background.
*Once you have changed the background from the Digital Projection
logo to another, you cannot return the logo to background even by
using Factory Default. To do so, repeat the above steps. The Digital
Projection logo file is included on the supplied CD-ROM Projector
User Supportware in folder (“/Logo/” ).
m Making Freehand Drawings on a Projected
Image (ChalkBoard)
The ChalkBoard feature allows you to write and draw messages on a pro-
jected image.
NOTE: The ChalkBoard feature is available only when a USB mouse is used.
From the menu, select [Tools] → [ChalkBoard] to display the ChalkBoard
tool bar that contains the following icons.
NOTE: You can also display the ChalkBoard tool bar by clicking the scroll button onyour USB mouse.
PenEraser Drive
Exit
Clear Color
Pen.............. Left-click and drag to draw. Left-click [
] or right-click the
pen icon to display the pen palette containing four lines of
different thickness from which you can select a line you pre-
fer by left-clicking.
Color ........... Selects a color. Left-click to display the color palette from
which you can select a color you prefer by left-clicking.
Capture ....... Left click to capture and save freehand drawings in the PC
card. (SHOWlite 6000gv only)
Eraser ......... Left-click and drag to erase part of a drawing. Left-click [
]
or right-click the eraser icon to display the eraser palette
containing four eraser of different thickness from which you
can select an eraser you prefer by left-clicking.
Clear ...........Left-click to clear the drawing completely from the
ChalkBoard screen.
Drive ............ Switches between PC Card slot. (SHOWlite 6000gv only)
Hide ............. Hides the tool bar by left-clicking. Right-clicking anywhere
on the screen displays the ChalkBoard tool bar again.
Exit .............. Clears the complete drawing and exits the ChalkBoard.
NOTE:
•The menu is not available while you display the ChalkBoard screen.
•Switching slides clears a drawing completely.
CaptureHide
4. Convenient Features 
						

							4-5
This function serves to store the adjusted value when using the Shift, Focus, and
Zoom buttons of the projector or the remote control.
Reference memory:
Reference  Point ....... Adjusted settings are stored in memory as a reference com-
mon to all the input sources. If no setting is stored in Cus-
tom Point, the adjusted settings in Reference Point will be
applied.
Custom memory:
Custom Point ........... Adjusted settings are stored in memory for each input sig-
nal.
Usage Example
When you wish to display on a screen having a 4:3 aspect ratio an NTSC or other
4:3 aspect ratio signal and an SXGA or other 5:4 aspect ratio signal:
Perform shift, focus, and zoom adjustments to set the vertical screen size of the
vertically tall 5:4 aspect ratio signal to standard.
Both 4:3 apsect ratio signals and 5:4 aspect ratio signals can now be displayed.
Note that with these shift, focus, and zoom adjustments, the 4:3 aspect ratio signal
will become smaller on the screen.
To eliminate this size reduction, adjust the shift, focus and zoom to the optimum
condition for each of the 4:3 aspect ratio signal and the 5:4 aspect ratio signal.
Memory (storage) of each of these values will permit projection at an optimum con-
dition upon signal switching.
1. Perform Zoom, Focus and Lens Shift adjustments and store them in memory
using “Set Custom Point”.
Another way to store your adjustments is to use the CTL and INFO buttons on
the remote control.
2. When “Yes” is selected for “Use Point on Signal Change”, the adjustment is ap-
plied to the signal you switched.
3. Select “OK” and press the ENTER button for the change to take effect.
NOTE: The Lens Memory function is not available in Link mode.
NOTE: The other optional lenses than GT10RLB, GT13ZLB, GT20ZL, GT24ZLB and GT34ZLB do not support
Lens Memory function. (On GT10RLB focus can be stored in memory)
You cannot store settings for zoom and focus on the following lenses:
GT13ZL, GT19ZL, GT24ZL and GT34ZL.
Picture Mute during Lens Shift?
To turn off the image and sound during lens shift, select Yes.
NOTE: This option is only available when Yes is selected for Use Point on Signal Change?.
, Lens Memory
4. Convenient Features 
						

							5-1
5
Using the Viewer
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
z Making the Most out of the Viewer Function ............. 5-2
x Operating the Viewer Function from the Projector
(playback) ................................................................. 5-3 
						

							5-2
PC
 C
O
N
T
R
O
L
IN
IN O
U
T
O
U
T SC
 T
R
IG
G
E
RR
E
M
O
T
E 2 R
EM
O
TE
 1 L
AN
A
C IN
 
U
SB
 (M
O
U
S
E
/
H
U
B)US
B
 (P
C)PC
 C
A
R
D2
1
NOTE:
•To use the Viewer, first you need to create presentation materials on your PC
using the Dynamic Image Utility 2.0 contained on the supplied Projector User
Supportware CD-ROM. For installation, see “6- 
b Software Installation”. For
creating presentation materials, see the Slide show function on the on-line manual
of the Dynamic Image Utility 2.0.
•Selecting Viewer sets the audio input for DVI input.
z Making the Most out of the Viewer Function
Features
You can view presentation data, capture (SHOWlite 6000gv only),
and play images on the projector. A PC card is used to view pre-
sentation data prepared on the computer and to capture and play
images projected with the projector.
The Viewer feature allows you to view slides stored on a PC
memory card (referred to as PC card in this manual) on the pro-
jector. Even if no computer is available, presentations can be
conducted simply with the projector. This feature is convenient
for holding presentations at meetings and in offices, as well as
for playing images taken on digital cameras.
Easy to use
•Presentations can be started immediately simply by inserting a
PC card (not supplied)
•Easy slide switching
•Remote control operation
•Jumping to list of slides or any specific slide
High quality images
•High resolution up to 1024 x 768 dots
•24-bit full color playback
•Viewing of digital camera images
Simple utility software (for computer)
•Dynamic Image Utility 2.0 operable on Windows 98/Me/XP/2000
•Slides can be created by capturing the currently displayed image
(SHOWlite 6000gv only)
•Control screen for displaying lists of slides and editing
*Microsoft, Windows and PowerPoint are registered trademarks of
Microsoft Corporation.
Removing the PC Card
Press the eject button slowly. The eject button card pops out a
little. Press the eject button slowly again. Grasp the edges of
the PC card and pull it out. Push and insert the eject button
fully until it stops.
Eject button
NOTE: Do not eject the PC card while its data is being accessed.
CAUTION: Make sure that the PC card or LAN card is removed
during Standby mode (NOT Idle mode)or with the main power
off.Failure to do so may cause damage to the data on your PC
card or LAN card,or may cause the projector to
malfunction.Should a malfunction occur, turn off the main power
and turn it back on.
Direction for Inserting the PC Card
The PC card has a top and bottom and must be inserted into the
PC card slot in a specific direction. It cannot be inserted back-
wards or upside-down. Attempting to force it into the slot in the
wrong direction may break the internal pin and damage the card
slot. Refer to the PC cards operating instructions for the proper
direction of insertion.
PC Card Type
The PC Card slot accepts PCMCIA Type II only. Inserting and Removing a PC Card
NOTE:
•Do not try to force the PC card into the slot.
PC CARD2
1
PC CONTROL
IN
IN OUT
OUT SC TRIGGER
REMOTE 2 REMOTE 1 LAN
AC IN 
USB (MOUSE/HUB)USB (PC)PC CARD2
1
NOTE: When using two PC cards, do not insert both PC cards into the two PC card
slots simultaneously. Doing so may cause projector malfunction such as shutting
down. Each PC card must be inserted slowly one at a time.
Inserting the PC Card•Hold the PC card horizontally and inser t it slowly into PC card slot
1 or 2 with its top facing up.
5. Using the Viewer
PC card (not supplied) 
						

							5-3
x Operating the Viewer Function from the
Projector (playback)
This section describes the operation for showing slides of pre-
sentation documents created using the Viewer function with the
projector. It is also possible to make slides directly from the im-
ages projected with the projector.
Projecting slides (Viewer)
1. Insert a PC card into the PC card slot.
Insert the PC card so that the end with the insertion direction arrow on
the top goes in first.
*Press the eject button to eject the card.
2. Select the Viewer from the Source Select menu.
3. Project slides.
Checking Show Folder List, means that selecting Viewer input
displays a list of the folders in the PC card and if Auto Play is
checked the projector automatically starts to play slides at the
first slide of the folder you have selected.
A tool bar will appear when you press the MENU button on the
remote control or the projector cabinet or clicking with the right
button of a mouse.
The tool bar includes the following buttons:
Prev .......... Returns to the previous slide or folder. Or this lets
you play slides back in reverse.
Next .......... Advances to the next slide or folder. Or this lets you
play slides back.
Play .......... Plays back automatically or manually depending on
the setting on Viewer Options of the menu. This al-
lows you to move on to the next slide when Manual
Play is selected.
Stop .......... This allows you to stop Auto Play while you are play-
ing back and to resume playing from the selected
slide or folder when Auto Play is selected.
Jump ........ Displays a list of slides while you are playing back.
Select ....... Displays a list of folders while you are playing back.
Drive ......... Switches between PC Card slot.
Setup ........ Displays the Viewer Options dialog box on Page 2 of
the Setup dialog box.
Delete ....... Deletes a captured slide(s) or all the captured slides
in the Capture - specific folder. (SHOWlite 6000gv
only)
View ......... Hides the tool bar while you are playing back. Press-
ing the MENU button or clicking with the right button
of a mouse shows it again.
NOTE: If no memory card is inserted in the PC CARD slot, there is no signal, and a
black, blue or logo background is displayed, depending on the setting.
Playback is stopped when 
 button on the cabinet is pressed in Auto Play mode.
Up to 12 indexes can be displayed on the list of folders. The folder in the right
bottom is always a folder exclusively for captured images, but is only displayed
when images have been captured. (SHOWlite 6000gv only)
When the tool bar is not displayed:
You can use the  and  button on the cabinet to select folders
or slides.
Folder
02 : 0001 / 0008Folder Folder Folder
Folder
Multi cursor (blue marks)
Current folder number
Current slide
numberNumber of all slides in folder
SlideSlide Slide Slide
Slide
SlideSlideSlide
02 : 0004 / 0008
Slide(Table) cursor
(green marks)
Folder
Use the SELECT  or  button to advance to the next folder
or return to the previous folder.
Use the SELECT  or  button to advance to the next slide or
return to the previous slide.
Prev Play Jump Drive
View
Next Stop SelectDelete
Setup
5. Using the Viewer
3D REFORM3D A
SELECT
STATUS LAMP 2 POWER
ON/STAND BY
AUTO ADJUST
MENU
ENTERCANCEL
3D REFORM3D
SELECT
STATUS LAMP 2 POWER
ON/STAND BY
MENU
ENTERCANCEL 
						

							5-4
Auto Play Mode
If the Auto Play option is selected in Viewer Options of the
menu, any given slide will start to play automatically.
You can also specify Auto Play Interval between 5 and 300 sec-
onds.
Switching to Slides Directly from Other Input Modes
With this function it is possible to switch directly to a slide when
the picture of a VCR or computer is being projected.
Example: When conducting presentations using a combination
of slides and moving pictures from a VCR, etc., it is possible to
switch from a Viewer slide to the video picture then back to the
Viewer slide simply by using the SELECT button.
NOTE: Even if you switch the current Viewer source to another source, the current
slide is retained. When you return back to the Viewer, you will get the slide that has
been retained.
The PC card editing operation cannot be performed from the pro-
jector. Do so using the Dynamic Image Utility 2.0 software.
Viewing Digital Images
Digital images can be played with the Viewer if the following con-
ditions are met:
•If the image can be stored on an MS-DOS format PC card
•If the image can be stored in a format supported by the Viewer. With the
Viewer, images on the card are searched for in directories and images
in JPEG or BMP format are recognized as slides. Searchable directo-
ries are directories within two steps from the root directory, and search-
able images are images within the first 12 files in the directory. Only file
and slide switching are possible.
NOTE: The maximum number of images recognized as slides within one directoryis 128.
Storing Images Displayed on the Projector on the PC card
(Capture) [SHOWlite 6000gv only]
The Capture features allows you to capture an image from a
source that is currently being displayed. The image is saved as
JPEG in the PC card. When you select Capture from the menu,
you will get a tool bar. You can capture an image directly using
the tool bar when the menu is not displayed.
NOTE:
*Unless a PC card is inserted into the PC Card slot of the projector, the Capture
feature is not available.
*The Card Error display means that the free space of the PC card is insufficient
for saving images. Make more space available on the card by erasing unwanted
images with your PC. The number of images that can be captured depends on
the size of the PC card.
Preparations:
Insert the PC card into the card slot.
Insert the PC card so that the end with the insertion direction
arrow on the top goes in first.
* Press the eject button to eject the card.
1. Project the image you wish to store on the projector.
2. Select the Capture from the Tools menu.
3. A tool bar will appear.
Freeze
Exit
Capture
Drive
The tool bar includes the following buttons:
Capture .... Captures an image and save it as a JPEG file on a
PC card.
Freeze ...... Freezes and unfreezes images.
Drive ......... Switches between PC Card slot.
Exit ........... Exits the Capture function. Another option to exit the
Capture function is to press MENU or CANCEL but-
ton on the remote control or projector cabinet.
NOTE:
You can compress a captured file (JPEG) using the Capture Options in the Setup
dialog. See page 8-15.
Captured images with higher resolution than the projectors native resolution can-
not be displayed correctly.
•File size of the captured image varies depending on the resolution of an input
signal.
•An hourglass indicating that an image is being captured appears on the projectors
display. Do not eject the PC card or turn off the projectors power while this icon
is displayed. Doing so will damage the PC card data. If the PC card data is dam-
aged, use a computer to repair the data.
5. Using the Viewer
CAUTION: Make sure that the PC card is removed during Standby
mode (NOT Idle mode) or with the main power off.
Failure to do so may cause damage to the data on your PC card,
or may cause the projector to malfunction.
Should a malfunction occur, turn off the main power and turn it
back on. 
						

							5-5
Deleting Captured Images
Using the Delete button on the tool bar for Viewer can delete
captured images.
To delete captured images:
1. Select Viewer and display a folder list of captured images.
2. Use 
 button to select the Capture folder “Cap” in the right bottom of
the screen.
3. Press the MENU button to display the tool bar.
4. Use the 
 or  button to select the Delete icon and press the ENTER
button or click with a mouse button.
Using the PC Card Files Fucntion (PC Card Files)
The PC Card Files function allows you to display a list of all the
files stored in the PC card so that you can select a file you want
to display. You can also sort files by file name or date, or display
the file. Although a list of all the files in the PC card is displayed,
you can view files in idx, text, HTML, JPEG and BMP format only.
Selecting BMP and JPEG files automatically switches to the
Viewer source. See also page 5-3.
NOTE: This option is not available for selection unless a PC card is inserted prop-erly.
Selecting Execute displays the file you selected.
When you select a JPEG or BMP file and press the ENTER but-
ton on the remote or the cabinet, or Execute on the above, you
will get a toolbar. This toolbar is used to return to the PC Card
Files screen.
Prev Play Jump Drive
View
Next Stop SelectDelete
Setup
Return ......... Returns to the PC Card Files screen.
Close ........... Close the toolbar.
ReturnClose
5. Using the Viewer 
						

							6-1
6
Using the Projector in a Network
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
z Introduction................................................................ 6-2
x Supported Projectors................................................. 6-3
c Equipment Connections and Settings........................ 6-4
v Software Installation................................................... 6-5
b Starting/Exiting the Software ...................................... 6-6
n Troubleshooting.......................................................... 6-7 
						

							6-2
z Introduction
Thank you for your purchase of the Digital Projection portable
projector (hereafter referred to as unit or projector).
This projector is connected to a personal computer or other equip-
ment and clearly projects text or graphics to a screen.
This projector is supplied with convenient software that allows
presentations to be made more simply and effectively. This guide
gives an overview and describes the use of the accompanying
software (contained in the CD-ROM that is supplied with this pro-
jector). Look over this guide in conjunction with the Help func-
tions of the software programs.
Contents of the Supplied CD-ROM
The supplied CD-ROM contains the following software programs:
• Dynamic Image Utility 2.0
• Viewer PPT Conver ter 2.0
• Image Express Utility 1.0
Please see the Help functions of the software programs for infor-
mation about their functions and operation.
What Can Be Accomplished with the Supplied Software
Dynamic Image Utility 2.0
•Converts PowerPoint files, JPEG images, and other files and cre-
ates slides that can be displayed with the viewer function of the
projector.
• Captures portions of the image from the screens of word processors,
spreadsheets, browsers, and other programs for use in presenta-
tions.
•By saving the created slides on a flash memory card (*1) and in-
ser ting the card into the PC Card slot of the projector, the slides
can be projected to the screen without connecting a personal com-
puter.
•The connection of personal computers and projectors by means of
a network environment (*2) or connection with USB cable or serial
cable allows the following uses. (In a network environment or USB
cable connection, support of multiple units is permitted.)
(1) Images and slides can be sent from the personal computer to the
projector and then projected to the screen. When using Microsoft
PowerPoint 2000/2002, slides can be sent synchronized with the
slide show page feed.
(2) A personal computer can be used to switch the projector power
on/off, control the adjustment of image quality and other settings,
and to display the remaining lamp life.
Viewer PPT Converter 2.0•Converts files created with Microsoft PowerPoint 95/97/2000/2002
to an independent index format with a simple operation to enable
direct playback with the viewer function of the projector.
•When using Microsoft PowerPoint 2000/2002, Viewer PPT Con-
verter 2.0 can be started from PowerPoint (by means of add-in
registration to PowerPoint).
Image Express Utility 1.0•Using a network environment (*2), this program enables the screen
image displayed by the personal computer to be sent to the projec-
tor and then projected to a screen.
•Two methods are available for sending the screen image to the
projector. Continuous Transmit automatically sends the screen
image of the personal computer at a fixed interval. Single Frame
Transmit sends the screen image by clicking the screen button (or
pressing a key).*1:Please purchase a commercially available PCMCIA Type 2 (ATA
specification) flash memory card.
*2:Please check the network environment on the next page.
Information about Upgrading this Software
Please see the service page for Digital Projection projectors on
the Digital Projection web site for information about software up-
grades of Digital Projection Projector User Supportware (i.e., Dy-
namic Image Utility, Viewer PPT Converter, and Image Express
Utility).
Projector Easy Connection Settings
The Easy Connection option is a mode that can abbreviate the
troublesome LAN settings when using the Image Express Utility
and connecting the PC and projector via a wireless LAN.
•From the Advanced menu, select [Projector Options] → [LAN Mode] →
[Status] → [Advanced] → [Network Type] → [Mode] → [Easy Connec-
tion] on the projector. (No setting for IP address, SSID and channel are
required.)
•After you have installed the software from the supplied CD-ROM to
your PC, before executing Easy Connection using Image Express Util-
ity, visit our website to update the information about Image Express
Utility and its related software.
Software can be downloaded from our website at no charge.
•Easy Connection is available on Windows 2000 Professional, Windows
XP Professional and Windows XP Home Edition (not available on Win-
dows XP Tablet PC Edition [with Image Express Utility 1.0 version
1.01.0003]).
•Easy Connection is available only when both PC and projector use the
Digital Projection optional wireless cards.
•Easy Connection is not available on Dynamic Image Utility included on
the supplied CD-ROM.
6. Using the Projector in a Network