Digital Projection Showlite 3000sx, 4000gv User Manual

							DVI L/MONO
L/MONO
RGB 2
RGB 1
VIDEO 1
VIDEO 2
S-
VIDEO AUDIO OUTR/Cr G/Y B/Cb
V H/HV MONITOR OUTR
L/MONO R L/MONO R
L/MONO R L/MONO RR
-
Connecting a DVD Player with Component Output
This type of input device requires the optional Component V cable for connection to
the projector.
1. Turn off the power to your projector and DVD Player.
2. Connect one end of the Component V cable to your DVD player and the other
end to the RGB1 input on the projector. Alternatively, use a D-Sub 15 Pin cable to
connect to the RGB2 input.
3. Turn on the projector and the DVD player.
Refer to your DVD users manual for more information about your equipmentÕs
video and audio output requirements.
BÑ15
System Installation
INSTALLATION
LBV00073; Revision A - 11/01/2002
HD VCR
DVD Player
Audio Equipment 
						

							Connecting a PC or Macintosh Computer
Connecting your PC or Macintosh computer to the projector allows you project the
output onto a large screen for presentations.
1. Turn off the power to your projector and computer.
2. Use an RGB cable to connect your computer to the projector (an RGB cable is 
supplied with the SHOWlite 4000gv projector).
3. Turn on the projector and the computer.
If the projector goes blank after a period of inactivity, it may be caused by a
screen saver installed on the computer.
Refer to your computers users manual for more information about your 
equipmentÕs video and audio output requirements.
BÑ16
System Installation
INSTALLATION
LBV00073; Revision A - 11/01/2002
DVI L/MONO
L/MONO
RGB 2
RGB 1
VIDEO 1
VIDEO 2
S-
VIDEO AUDIO OUTR/Cr G/Y B/Cb
V H/HV MONITOR OUTR
L/MONO R L/MONO R
L/MONO R L/MONO RR
-
-
RGB
Signal
CableRGB
Signal
Cable
Pin Adapter for Macintosh (not supplied)
For older Macintosh, use a commercially available pin
adapter to connect to your MacÕs video port
PC Macintosh 
						

							Connecting to a PC with DVI Output - SHOWlite 3000sx
The DVI (digital) input accepts signals up to SXGA@60Hz. SXGA signals \
with a
clock signal of 110MHz or over cannot be supported.
The Auto Adjust feature does not work for DVI digital signals. When a DV\
I 
signal is selected and the image position is not correct, adjust the hor\
izontal and
vertical position using the Pixel/Clock screen.BÑ17
System Installation
INSTALLATION
LBV00073; Revision A - 11/01/2002
-
L/MONO
L/MONORGB 2
RGB 1
VIDEO 1
VIDEO 2
S-
VIDEO AUDIO OUT R/Cr G/Y B/Cb
V
H/HV R
L/MONO R
L/MONO R L/MONO R R
L/MONO R
OUTPUTANALOG
DVI DIGITAL
DVI DIGITAL
DVI Cable
(not supplied)
Supplied Ferrite Clamp Core
To DVI Digital 
						

							Connecting to a PC with DVI Output - SHOWlite 4000gv
The DVI (digital) input accepts the XGA signal produced from DVI equipment
however a DVI cable will be required.
The Auto Adjust feature does not work for DVI digital signals. When a DVI 
signal is selected and the image position is not correct, adjust the horizontal and
vertical position using the Pixel/Clock screen.
BÑ18
System Installation
INSTALLATION
LBV00073; Revision A - 11/01/2002
DVI L/MONO
L/MONO
RGB 2
RGB 1
VIDEO 1
VIDEO 2
S-
VIDEO AUDIO OUTR/Cr G/Y B/Cb
V H/HV MONITOR OUTR
L/MONO R L/MONO R
L/MONO R L/MONO RR
-
DVI Cable
(not supplied)
Supplied Ferrite Clamp Core To DVI Digital or DVI Analog 
						

							DVI L/MONO
L/MONO
RGB 2
RGB 1
VIDEO 1
VIDEO 2
S-
VIDEO AUDIO OUTR/Cr G/Y B/Cb
V H/HV MONITOR OUTR
L/MONO R L/MONO R
L/MONO R L/MONO RR
Connecting to a Single Workstation
1. Turn off the power to your projector and workstation.
2. Use a BNC x 5 cable to connect your workstation and the RGB1 connector on 
your projector.
3. Turn on the projector and workstation.
BNC x 5 INSTALLATION INSTRUCTIONS
To reduce unnecessary radiation of electromagnetic waves, fit the optional ferrite
core to one end of the BNC cable.
1. Open and attach the ferrite core to a signal cable as close as possible to the 
projector end of the cable. Close the ferrite core tightly.
2. Fix the optional band to the cable as a stopper. Pull the end of the band to 
tighten it and cut off the remaining band.
BÑ19
System Installation
INSTALLATION
LBV00073; Revision A - 11/01/2002
Signal DistributionBNC x 5 Cable
To RGBHV output To RGBHV output
To Analog
RGB InputTo Analog
RGB Output
Workstation 
						

							Connecting an External Monitor - SHOWlite 3000sx
You can connect a separate, external monitor to your SHOWlite 3000sx projector to
simultaneously view the RGB analog or component image you are displaying on the
projector.
1. Turn off the power to the projector, monitor and computer.
2. Use a 15pin cable to connect your monitor to the ANALOG OUTPUT (Mini D-
Sub 15 pin) connection on the projector.
3. Turn on the projector, monitor and computer.
BÑ20
System Installation
INSTALLATION
LBV00073; Revision A - 11/01/2002
L/MONO
L/MONO
RGB 2
RGB 1
VIDEO 1
VIDEO 2
S-
VIDEO AUDIO OUTR/Cr G/Y B/Cb
V H/HVR
L/MONO R
L/MONO R L/MONO RR
L/MONO R
OUTPUTANALOG
DVI DIGITAL
DVI DIGITAL
DVI DIGITAL Input
Supplied Ferrite Clamp Core
SLAVE PROJECTOR
MASTER PROJECTOR 
						

							-
-The ANALOG OUTPUT connector outputs RGB signal during standby. When
the projector is placed into standby mode the external monitor will disappear for a
moment.
The DVI DIGITAL OUTPUT connector outputs all input signals. This connector
is designed for Link Mode only. Do not connect any other equipment other than
another projector to this connector.
BÑ21
System Installation
INSTALLATION
LBV00073; Revision A - 11/01/2002 
						

							Connecting an External Monitor - SHOWlite 4000gv
You can connect a separate, external monitor to your projector to simultaneously
view the RGB analog, DVI analog or component image you are displaying on the
projector.
1. Turn off the power to the projector, monitor and computer.
2. Use a 15pin cable to connect your RGB monitor to the RGB MONITOR 
OUTPUT connection on the projector.
3. Turn on the projector, Monitor and computer.
The MONITOR OUTPUT connector outputs RGB signal during standby. When
the projector is placed into standby mode the external monitor will disappear for a
moment.
The DVI digital output signal from the MONITOR OUTPUT connector is not
available.
BÑ22
System Installation
INSTALLATION
LBV00073; Revision A - 11/01/2002
DVI L/MONO
L/MONO
RGB 2
RGB 1
VIDEO 1
VIDEO 2
S-
VIDEO AUDIO OUTR/Cr G/Y B/Cb
V H/HV MONITOR OUTR
L/MONO R L/MONO R
L/MONO R L/MONO RR
-
- 
						

							Remote Control Overview ............................................... CÑ1
Direct Key Combinations ........................................... CÑ6
Menu System Overview ................................................... CÑ7
Navigating the Menu System .................................... CÑ9
Menu Operation - SHOWlite 3000sx ..............................CÑ10
Menu Structure .........................................................CÑ12
Advance Menu - SHOWlite 3000sx...............................CÑ14
Adjust Source - SHOWlite 3000sx ..................................CÑ19
Picture .......................................................................CÑ19
White Balance ..........................................................CÑ20
Image .......................................................................CÑ21
Video Adj ..................................................................CÑ24
Option Adj ................................................................CÑ26
Signal Type ...............................................................CÑ27
Volume - SHOWlite 3000sx .............................................CÑ27
Ref Adj - SHOWlite 3000sx .............................................CÑ27
Keystone ...................................................................CÑ27
Lamp Mode ..............................................................CÑ28
Ref. White Bal. ..........................................................CÑ28
Factory Default - SHOWlite 3000sx...............................CÑ29
System Operation
Section C: System Operation
OPERATION
LBV00073; Revision A - 11/01/2002 
						

							Projector Options - SHOWlite 3000sx .............................CÑ30
Timer .........................................................................CÑ30
Menu ........................................................................CÑ32
Setup .........................................................................CÑ35
Link Mode .................................................................CÑ42
Help - SHOWlite 3000sx .................................................CÑ43
Contents ...................................................................CÑ43
Source Information ...................................................CÑ43
Projector Information  ................................................CÑ43
Test Pattern - SHOWlite 3000sx .....................................CÑ45
Menu Operation - SHOWlite 4000gv .............................CÑ46
Menu Structure .........................................................CÑ48
Advance Menu - SHOWlite 4000gv ...............................CÑ50
Source Select - SHOWlite 4000gv..................................CÑ51
Entry List ...................................................................CÑ51
Picture - SHOWlite 4000gv.............................................CÑ54
Volume - SHOWlite 4000gv............................................CÑ54
Image Options - SHOWlite 4000gv................................CÑ55
Keystone ...................................................................CÑ55
Color Temperature ...................................................CÑ56
Lamp Mode ..............................................................CÑ56
System Operation
OPERATION
LBV00073; Revision A - 11/01/2002