Home
>
Digital Projection
>
Projector
>
Digital Projection Projector HIGHlite 740 Series User Manual
Digital Projection Projector HIGHlite 740 Series User Manual
Here you can view all the pages of manual Digital Projection Projector HIGHlite 740 Series User Manual. The Digital Projection manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 31
page 22 Connection Guide SIGNAL INPUTS AND OUTPUTS 5 Composite 1 (CVBS 1) Uses a BNC connector to receive a Composite Video input signal. 6 S-Video Uses a 4-pin mini-DIN connector. 7 3G-SDI Uses a BNC connector to receive uncompressed, unencrypted digital video. If two video streams are being transmitted, set 3G Level B Stream in the Setup/ Input Configuration menu to choose one of them. 8 VGA Receives analog signal from a computer. When using this input, it is best to use a fully wired VGA cable to...
Page 32
![Page 32
page 23
Connection Guide
SIGNAL INPUTS AND OUTPUTS
EDID on the DVI and VGA inputs
If you connect a computer graphics card or other source which uses DDC t\
o discover the capabilities of the attached display, it will
automatically configure itself to the best settings when connected to the projector via DVI, HDMI or VGA inputs.
Otherwise refer to the documentation supplied with the source to manuall\
y set the resolution to the DMD™ resolution of the projector or the
nearest suitable setting. Switch...](http://img.usermanuals.tech/thumb/5761/99654/w300_projector_manual_8497_d-31.png "Page 32
page 23
Connection Guide
SIGNAL INPUTS AND OUTPUTS
EDID on the DVI and VGA inputs
If you connect a computer graphics card or other source which uses DDC t\
o discover the capabilities of the attached display, it will
automatically configure itself to the best settings when connected to the projector via DVI, HDMI or VGA inputs.
Otherwise refer to the documentation supplied with the source to manuall\
y set the resolution to the DMD™ resolution of the projector or the
nearest suitable setting. Switch...")
page 23 Connection Guide SIGNAL INPUTS AND OUTPUTS EDID on the DVI and VGA inputs If you connect a computer graphics card or other source which uses DDC t\ o discover the capabilities of the attached display, it will automatically configure itself to the best settings when connected to the projector via DVI, HDMI or VGA inputs. Otherwise refer to the documentation supplied with the source to manuall\ y set the resolution to the DMD™ resolution of the projector or the nearest suitable setting. Switch...
Page 33
page 24 Connection Guide CONTROL CONNECTIONS Control Connections 1 Update port All of the projector’s features can be controlled via a serial connection, using the commands described in the Protocol Guide. In addition, the Update port is used to download, via LAN, firmware updates issued from time to time by Digital Projection. Use a crossed LAN cable to connect directly to a computer, or an uncrossed cable to connect to a network hub. 2 RS232 All of the projector’s features can be controlled via a...
Page 34
![Page 34
page 25
Connection Guide
CONTROL CONNECTIONS
LAN connection examples
The projector’s features can be controlled via a LAN connection, using a standard internet browser \
package.
Back panel
1
Notes
Hub or LANComputer
Projector
Projector
Un-crossed LAN cables
Projector
Computer
Crossed
LAN cable
1LAN
Digital Projection HIGHlite 740 Series
Rev I Februar y 2015](http://img.usermanuals.tech/thumb/5761/99654/w300_projector_manual_8497_d-33.png "Page 34
page 25
Connection Guide
CONTROL CONNECTIONS
LAN connection examples
The projector’s features can be controlled via a LAN connection, using a standard internet browser \
package.
Back panel
1
Notes
Hub or LANComputer
Projector
Projector
Un-crossed LAN cables
Projector
Computer
Crossed
LAN cable
1LAN
Digital Projection HIGHlite 740 Series
Rev I Februar y 2015")
page 25 Connection Guide CONTROL CONNECTIONS LAN connection examples The projector’s features can be controlled via a LAN connection, using a standard internet browser \ package. Back panel 1 Notes Hub or LANComputer Projector Projector Un-crossed LAN cables Projector Computer Crossed LAN cable 1LAN Digital Projection HIGHlite 740 Series Rev I Februar y 2015
Page 35
page 26 Connection Guide CONTROL CONNECTIONS RS232 connection exampleNotes Projector Computer Null-modem cable Back panel with control connections 1 1RS232 Digital Projection HIGHlite 740 Series Rev I Februar y 2015
Page 36
OPERATING GUIDE4 Rev I Februar y 2015 HIGHlite 740 Series High Brightness Digital Video Projector
Page 37
![Page 37
Operating Guide
IN THIS GUIDE
IN THIS GUIDE
Using The Menus ........................................................................\
.......................29
Menus and sub-menus .............................................................................................29
Drop-down lists .........................................................................................................30
Sliders...](http://img.usermanuals.tech/thumb/5761/99654/w300_projector_manual_8497_d-36.png "Page 37
Operating Guide
IN THIS GUIDE
IN THIS GUIDE
Using The Menus ........................................................................\
.......................29
Menus and sub-menus .............................................................................................29
Drop-down lists .........................................................................................................30
Sliders...")
Operating Guide IN THIS GUIDE IN THIS GUIDE Using The Menus ........................................................................\ .......................29 Menus and sub-menus .............................................................................................29 Drop-down lists .........................................................................................................30 Sliders...
Page 38
![Page 38
page 29
Operating Guide
USING THE MENUS
Using The Menus
Use the buttons on the projector control panel or on the remote control,\
to access the menu system.
• To open or close the on-screen display (OSD), press MENU.
Menus and sub-menus
• To open a sub-menu, select it using the UP and DOWN arrow buttons, then press OK.
• To return to the previous menu, press EXIT.
Notes
Some menu items may not be
available due to settings in other
menus. These will be grayed out on
the actual menu.
When a globe...](http://img.usermanuals.tech/thumb/5761/99654/w300_projector_manual_8497_d-37.png "Page 38
page 29
Operating Guide
USING THE MENUS
Using The Menus
Use the buttons on the projector control panel or on the remote control,\
to access the menu system.
• To open or close the on-screen display (OSD), press MENU.
Menus and sub-menus
• To open a sub-menu, select it using the UP and DOWN arrow buttons, then press OK.
• To return to the previous menu, press EXIT.
Notes
Some menu items may not be
available due to settings in other
menus. These will be grayed out on
the actual menu.
When a globe...")
page 29 Operating Guide USING THE MENUS Using The Menus Use the buttons on the projector control panel or on the remote control,\ to access the menu system. • To open or close the on-screen display (OSD), press MENU. Menus and sub-menus • To open a sub-menu, select it using the UP and DOWN arrow buttons, then press OK. • To return to the previous menu, press EXIT. Notes Some menu items may not be available due to settings in other menus. These will be grayed out on the actual menu. When a globe...
Page 39
page 30 Operating Guide USING THE MENUS Drop-down lists To use a drop-down list: 1. Navigate to the drop-down list in the menu and press OK. 2. Highlight an item from the list using the UP and DOWN arrow buttons. 3. Press OK again to select the highlighted item, or press EXIT to exit without changing. Notes Some menu items may not be available due to settings in other menus. These will be grayed out on the actual menu. When a globe icon appears next to a setting, the setting affects all...
Page 40
page 31 Operating Guide USING THE MENUS Sliders To use a slider, press the LEFT and RIGHT arrow buttons to adjust it. Commands To use a command, press OK. In the example below, press OK to confirm, or press EXIT to cancel. Notes Some menu items may not be available due to settings in other menus. These will be grayed out on the actual menu. When a globe icon appears next to a setting, the setting affects all sources and all inputs; otherwise, only the current input source will be affected if...