Digital Projection Projector HC M Vision Cine 400 User Manual

Rev A December 2010 Page 2.13
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 2. Installation

Notes
 For more detailed information 
about using the menus, see 
section 4. Controlling the 
projector.
 Do not try to stack more than 
three projectors.
 When stacking projectors, 
the stack MUST be vertical, to 
ensure that the stresses are 
distributed to all four chassis 
corners.
 Make sure that the surface, 
ceiling or rigging that is 
to support the projector is 
capable of...

Page 2.14 Rev A December 2010
2. Installation Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

Notes
 For more information on 
selecting an input source, see 
section 4. Overview, Using 
the control keys, and Using 
the menus.
  For more information about pin 
connections and control codes 
see section 6. Appendix.
Connecting the projector
Signal Inputs
The following inputs are available:
HDMI 1 & 2  HDCP-compliant digital video inputs from HDMI or DVI sources.
RGB  15 pin D-type...

Rev A December 2010 Page 2.15
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 2. Installation

Input connection examples, continued 

Page 2.16 Rev A December 2010
2. Installation Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

Notes
 
 For more information about pin 
connections and control codes 
see section 6. Appendix.
 For more information about the 
Trigger outputs see Control 
Menu in section 4. Controlling 
the projector.
Control connections
The following connections are available:
remote control
If infrared signals from the remote control cannot reach the projector d\
ue to 
excessive distance or...

Rev A December 2010 Page 2.17
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 2. Installation

Power connection
Lift the cable lock up, push the mains connector in firmly, then push the lock down to 
secure the cable.
Notes
 Use only the power cable 
provided.
 Ensure that the power 
outlet includes a Ground 
connection, as this 
equipment MUST be earthed.
 Handle the power cable 
carefully and avoid sharp 
bends. Do not use a damaged 
power cable.
Power 
connection 

Page 2.18 Rev A December 2010
2. Installation Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 

Rev A December 2010  Page 3.1
3. Getting Started
Contents
Positioning the screen and projector ........................................................................\
....................3.2
Switching the projector on ........................................................................\
.......................................3.2
Inserting batteries into the remote control ........................................................................\
...........3.2
Selecting an input signal or test...

Page 3.2 Rev A December 2010
3. Getting Started Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual

Switching the projector on
Connect the power cable between the mains supply and the projector.
Wait until the self-test has completed and the power indicator on the pro\
jector 
control panel shows steady blue. The lamp will be off and the projector will be in 
STANDBY mode.
Press POWER ON  on the remote control or POWER  on the projector 
control panel to switch the projector ON. The...

Rev A December 2010 Page 3.3
Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual 3. Getting Started

Selecting an input signal or test pattern
Input
Connect an video source to the projector. The signal should be automatically 
detected by the projector, and should be displayed within a two or three 
seconds.
If more than one signal is connected to the projector, then select which signal 
is to be displayed, using the  to   buttons on the remote control, or 
by pressing the SOURCE button...

Page 3.4 Rev A December 2010
3. Getting Started Digital Projection M-Vision Cine 230, Cine 260, Cine 400 User Manual
Adjusting the projected image
Aspect ratio
Press  on the remote control until the image is displayed in the corect aspect\
 
ratio.
Image quality settings
Press any of the following keys on the remote control, followed by  and , to 
adjust these image quality settings:
 Brightness   
Contrast   
Sharpness   
•
•
Notes
  For more detailed information 
about:
  - using all the control keys...