Digital Projection M-vision 1080p-260 User Manual

							
Rev A May 2010 Page 6.3
Digital Projection M-Vision 1080p-260 User Manual  6. Appendix

problempossible solutions
Image is split or otherwise scrambled.Check that the image source is not set to progressive scan.
Image is blurred.Check that the lens is focussed correctly.
Image is too bright, and lacks 
definition	in	the	bright	areas.Decrease the contrast setting.
See section 4. Controlling the projector, Using the control keys and Main 
menu
Image appears ‘washed out’ and is too 
bright in the dark areas
Decrease the brightness setting.
See section 4. Controlling the projector, Using the control keys and Main 
menu
Colors in the image are swapped. 
for example, reds appear blue or vice 
versa.
Check that the Component signals are connected correctly.
See Section 4. Installation, Connecting the projector.
Projector does not respond to control 
commands from a computer.
Check that the serial cable is connected correctly.
Check that the baud rate is set correctly.
See this section 6. Appendix, Connections
Check that the correct control codes are being used.
See this section 6. Appendix. Serial communications protocol
Projector does not respond to control 
commands from the remote control.
Check that the infra red windows at the front and rear of the projector or on the IR 
repeater are not obstructed. Check that the batteries are in good condit\
ion.
If you are using an IR repeater, check that the cable is connected properly at both 
ends, and that the cable is not damaged.
See section 4. Controlling the projector, The remote control
In the event that this troubleshooting guide has not solved the problem,\
 
then contact your Digital Projection dealer or service centre. 
						

							
Page 6.4  Rev A May 2010
6. Appendix  Digital Projection M-Vision 1080p-260 User Manual

Error codes
If the projector detects an error, the red Issue indicator will flash, as shown in the 
chart below.
For example, if the lamp door is left open, the red indicator will flash twice followed 
by a pause, then the sequence will repeat until the error condition is corrected.
Notes 
						

							
Rev A May 2010 Page 6.5
Digital Projection M-Vision 1080p-260 User Manual  6. Appendix

Specifications
Part numbers
Projector
0.73:1 fixed lens 109-729
1.56–1.86:1 zoom lens  109-658
1.85–2.40:1 zoom lens  109-680
Power cable 10A, Europe  102-163
Power cable 13A, North America  102-165
Power cable 10A, United Kingdom  102-180
Remote control  109-685
User manual on CD  110-288
Important Information  110-287
Getting Started Guide  110-286
Replacement parts
Lamp module 109-682
0.8x converter lens  109-727
1.25x converter lens  109-735
Optical
Digital Light Processor 1 x 0.95” Texas Instruments DMD™, resolution 1920 x 1080 pixels
Colour wheel  5-segment: Red/Yellow/Green/White/Blue (3x)
Contrast Ratio  2000:1 (±10%)
Colour temperature  Native: 7500°K (±1500°K), adjustable: 5500°K - 9300°K
Pixel	fill	factor   87%
Lamp power  260W
Lamp life (typical)  2000 hours
Brightness  3500 ANSI lumens (±10%)
Uniformity  85%
Focus range
0.73:1 Fixed lens 
to be confirmed
1.56–1.86:1 zoom lens  2–7m (6.6 - 23ft)
1.85–2.40:1 zoom lens  2.5–10m (8.2 - 32.8ft)
Image width
0.73:1 fixed lens 
to be confirmed
1.56–1.86:1 zoom lens 0.86 to 5.6m (2.8 - 18.4ft) depending on lens converter
1.85–2.40:1 zoom lens  0.81 to 6.86m (2.7 - 22.2ft) depending on lens converter 
						

							
Page 6.6  Rev A May 2010
6. Appendix  Digital Projection M-Vision 1080p-260 User Manual

Lens aperture
0.73:1 fixed lens F/2.5
1.56–1.86:1 zoom lens  F/2.5–2.76
1.85–2.40:1 zoom lens  F/2.17–2.46
Lens shift (zoom lenses only)
Vertical ± 0.6 H (120%)
Horizontal  ± 0.3 W (60%)
Electrical
Inputs  HDMI x 2, RGB, Component x 2, Video, S-Video
Pixel clock (digital)  up to 165MHz
Bandwidth (analog)  200MHz
Control inputs  1 x RS232 serial: 38400 baud, 8 bits, 1 stop bit, no parity
  1 x remote control
Mains voltage  100-240 VAC ±10%, 47-63Hz (single phase)
Power consumption
110V  347W in Running mode, 1.9W in Standby
240V  331W in Running mode, 2.5W in Standby
International Regulations Meets FCC Class B  requirements 
Meets EMC Directives (EN 55022, EN 55024) 
Meets Low Voltage Directive (EN60950)
Indicators  Power, Standby, Issue (Fault)
Physical
Temperature
Operating  0 to 35°C
Storage  -20 to 60°C
Thermal Dissipation  1500 BTU/hr
Humidity
Operating  20% to 90% non condensing
Storage   10% to 90%
Altitude
Operating up to 10,000 feet
Storage   up to 40,000 feet
Weight  9 kg (20 lbs)
Noise level  < 35 dB
 Specifications are subject to change without notice. 
						

							
Rev A May 2010 Page 6.7
Digital Projection M-Vision 1080p-260 User Manual  6. Appendix

Dimensions
All dimensions in mm unless otherwise stated 
						

							
Page 6.8  Rev A May 2010
6. Appendix  Digital Projection M-Vision 1080p-260 User Manual

Video formats supported
Signal TypeResolutionFrame 
RateHDMIRGB
Component 1:
RGB
Component 1:Y/Pr/Pb  Y/Cr/CbComponent 2:Y/Pr/Pb  Y/Cr
Video S-Video 
Reference
PC640x480 59.94xxxVESA DMT 
640x480 74.99xxxVESA DMT 
640x480 85xxxVESA DMT 
800x600 60.32xxxVESA DMT 
800x600 75xxxVESA DMT 
800x600 85.06xxxVESA DMT 
848x480 47.95xxxVESA CVT 
848x480 59.94xxxVESA CVT 
1024x768 60xxxVESA DMT 
1024x768 75.03xxxVESA DMT 
1024x768 85.03xxxVESA DMT 
1024x768 70.1xxxVESA DMT 
1280x720 47.95xxxVESA GTF 
1280 x 768 60xxxVESA DMT 
1280 x 768 60xxxVESA DMT Reduced Blanking
1280 x 768 75xxxVESA DMT 
1280 x 768 85xxxVESA DMT 
1280 x 800 50x xxVESA DMT
1280 x 800 60xxxVESA DMT 
1280 x 800 75xxxVESA DMT 
1280x1024 60.02xxxVESA DMT 
1280x1024 75.02xxxVESA DMT 
1280x1024 85.02xxxVESA DMT 
1440 x 900 60xxxVESA DMT 
1440 x 900 75xxxVESA DMT 
1400 x 1050 60xxxVESA DMT 
1400 x 1050 75xxxVESA DMT 
1600x1200 60xxxVESA DMT 
1920x1080 47.95xxxVESA CVT 
1600 x 1200 60xxxVESA DMT 
1920 x 1200 60xxxVESA DMT Reduced Blanking 
1680x1050 59.94xxxVESA CVT 
Apple Mac 640x480 66.59xxxVESA DMT 
832x624 74.54xxxVESA DMT  
						

							
Rev A May 2010 Page 6.9
Digital Projection M-Vision 1080p-260 User Manual  6. Appendix

Signal TypeResolutionFrame 
RateHDMIRGB
Component 1:
RGB
Component 1:Y/Pr/Pb  Y/Cr/CbComponent 2:Y/Pr/Pb  Y/Cr
Video S-Video 
Reference
NTSC NTSC (M, 4.43) 59.94x x ITU-R BT.1700, SMPTE 170M
PAL PAL (B,G,H,I) 50x x ITU-R BT.1700 
PAL (N) 50x x ITU-R BT.1700 
PAL (M) 59.94x x ITU-R BT.1700 
SECAM SECAM (M) 50x x ITU-R BT.1700 
480i 59.94xxxSMPTE 125M, CEA-861-D 
576i 50xxxITU-R BT.601, CEA-861-D 
EDTV 480p 59.94xxxxxSMPTE 293M, CEA-861-D 
576p 50xxxxxITU-R BT.1358, CEA-861-D 
HDTV 1035i 60xxxxxSMPTE 260M 
1080i 50xxxxxSMPTE 274M, CEA-861-D 
1080i (Aus) 50xxxxxSMPTE 295M 
1080i 59.94xxxxxSMPTE 274M, CEA-861-D 
1080i 60xxxxxSMPTE 274M, CEA-861-D 
720p 50xxxxxSMPTE 296M, CEA-861-D 
720p 59.94xxxxxSMPTE 296M, CEA-861-D 
720p 60xxxxxSMPTE 296M, CEA-861-D 
1080p 23.98xxxxxSMPTE 274M, CEA-861-D 
1080p 24xxxxxSMPTE 274M, CEA-861-D 
1080p 25xxxxxSMPTE 274M, CEA-861-D 
1080p 29.97xxxxxSMPTE 274M, CEA-861-D 
1080p 30xxxxxSMPTE 274M, CEA-861-D 
1080p 50xxxxxSMPTE 274M, CEA-861-D 
1080p 59.94xxxxxSMPTE 274M, CEA-861-D 
1080p 60xxxxxSMPTE 274M, CEA-861-D  
						

							
Page 6.10  Rev A May 2010
6. Appendix  Digital Projection M-Vision 1080p-260 User Manual

NotesInput connections
HDMI 1 & 2 inputs
19 way type A connector
1 TMDS Data 2+
2  TMDS Data 2 Shield
3  TMDS Data 2-
4  TMDS Data 1+
5  TMDS Data 1 Shield
6  TMDS Data 1-
7  TMDS Data 0+
8  TMDS Data 0 Shield
9  TMDS Data 0-
10  TMDS Clock+
11  TMDS Clock Shield
12  TMDS Clock-
13  CEC
14  not connected
15  SCL (DDC Clock)
16  SCA (DDC Data)
17  DDC/CEC Ground
18  +5 V Power
19  Hot Plug Detect
Composite video input
1 x 75 ohm BNC
PAL or NTSC video
S-Video input
4 pin mini-DIN
1 Y Ground
2  C Ground
3  Luminance (Y)
4  Chrominance (C)
pin view of panel connector
pin view of female connector 
						

							
Rev A May 2010 Page 6.11
Digital Projection M-Vision 1080p-260 User Manual  6. Appendix

pin view of female connector
RGB input
15 way D-type connector
1 R
2  G
3  B
4  unused 
5  Digital Ground (H Sync)
6  R Ground
7  B Ground
8  G Ground
9  +5v
10  Digital Ground (V Sync/DDC)
11  unused
12  SDA
13  H Sync
14  V Sync
15  SCL
Component 1 input
3 x RCA phono connectors
RGsB      YPbPr   YCbCr
Red      Pr   Cr
Green + Sync     Y    Y
Blue      Pb   Cb
Component 2 input
3 x 75 ohm BNC
YPbPr   YCbCr
Y       Y
Pb      Cb
Pr      Cr
Notes
 In most cases, the Auto setting 
will determine the correct color 
space to use. If it does not, 
you can select the appropriate 
setting manually. 
  To select between RGB and 
YPrPb signals, see Advanced 
Menu, in 4.Controlling the 
Projector. 
						

							
Page 6.12  Rev A May 2010
6. Appendix  Digital Projection M-Vision 1080p-260 User Manual

Control connections
Wired Remote control connection
3.5mm mini jack
Tip  Power
Ring  Signal
Sleeve  Ground
Trigger 1 & 2 output
3.5mm mini jack
Tip  Signal
Sleeve  Ground
Serial control input
1 unused
2  Received Data (RX)
3  Transmitted Data (TX)
4  unused
5  Signal Ground
6  unused
7  unused
8  unused
9  unused
Null-modem cable
(used to connect the projector to a modem)
RX  2 --- 3 TX
TX  3 --- 2 RX
GND  5 --- 5 GND
Serial port settings
Baud rate  38400 bps
Data length  8 bits
Stop bits  one
Parity  none
Flow control  none•
•
•
•
•
Notes
 Trigger outputs are normally 
at 0V, and rise to +12V when 
triggered.
 The projector is a DCE, so use:
a straight cable to connect to a 
computer, or
a null-modem cable as shown 
here to connect to another DCE 
such as a modem.
•
•
Sleeve
Ring
Tip
SleeveTip
pin view of female connector