Digital Projection Highlite 4100gv User Manual

							Packaging........................................................................ A—1
Projector Packaging.................................................... A—1
Lens Packaging........................................................... A—1
Safety Advice................................................................... A—2
Fire and Shock Precautions......................................... A—2
Lamp Precautions....................................................... A—2
Power Supply ............................................................. A—3
Installation Advice ..................................................... A—4
Components..................................................................... A—5
Part Names ................................................................. A—5
Control Panel ............................................................. A—6
Terminal Panel ........................................................... A—8
RGB Digital Connectors & Optional SDI Board .........A—10
Remote Control ........................................................A—13
Overview
Section A: Overview
OVERVIEW
LBV00072; Revision A - 25/09/2001 
						

							Overview
OVERVIEW
LBV00072; Revision A - 25/09/2001 
						

							Projector Packaging
The following components should be contained within the projector packaging.
Should any of the components be absent, please contact the dealer who supplied the
projector, or Digital Projection Limited (Digital Projection Inc. if in North
America) immediately.
1 x HIGHlite DisplaysProjector
1 x Remote Control Unit with Remote Cable (wireless/wired)
1 x AC Power Cable
1 x AC Power Cable Stopper
1 x DVI-D Cable
2 x AAA Batteries
1 x User Manual
1 x Foam Dust Cap
CompactFlash Memory Card (8MB) with adapter
All packaging should be retained to provide maximum protection during future
shipping of the projector.
Lens Packaging
Lenses are supplied as individual items and the packaging may differ depending on
the version ordered. Please refer to the instructions supplied with your lens.
A—1
Overview
Packaging
OVERVIEW
LBV00072; Revision A - 25/09/2001 
						

							The safety instructions provided in this manual are to ensure the long life of your
projector and to prevent fire and shock. Please read them carefully and heed all
warnings.
Fire and Shock Precautions 
Ensure that there is sufficient ventilation and that vents are unobstructed to prevent
potentially dangerous concentrations of ozone and the build-up of heat inside your
projector. Allow at least 20cm (8”) of space between your projector and a wall.
Allow at least 50cm (20”) of space between the ventilation duct outlet and object.
Ensure that nothing can be spilled on, or dropped inside the projector. If this does
happen, switch off and unplug the mains supply immediately. Do not operate the
projector again until it has been checked by qualified service personnel. 
Do not insert any metal objects such as a wire or screwdriver into your projector.
Lamp Precautions 
Due to the lamp being sealed in a pressurised environment, there is a small risk of
explosion, if not operated correctly. There is minimal risk involved, if the unit is in
proper working order, but if damaged or operated beyond the recommended 1500
hours, the risk of explosion increases.
The projector has a warning system that displays the following message when you
reach 1500 hours of operation - Lamp Running Time is Over 1500 Hours!!. When
you see this message please contact your Digital Projection dealer for a 
replacement lamp.
If the lamp does explode, smoke will be discharged from the vents located on the
side of the unit. This smoke is comprised of glass in particulate form and Xenon 
A—2
Overview
Safety Advice
OVERVIEW
LBV00072; Revision A - 25/09/2001 
						

							gas, and will not cause harm if kept out of your eyes. If your eyes have been
exposed to this gas, please flush your eyes out with water immediately and seek
immediate medical attention. Do not rub your eyes as this could cause 
serious injury.
WARNING: Do not look into the lens while the projector is on. Serious damage to
your eyes could result.
CAUTION: The high pressure lamp may explode if improperly handled. Refer all
servicing to qualified service personnel.
Power Supply
The projector is designed to operate on a power supply of 1.0kW 100-120VAC /
1.5kW 200-240VAC 50/60Hz. Ensure that your power supply fits this requirement
before attempting to use your projector.
Handle the power cable carefully and avoid excessive bending. A damaged cord can
cause electric shock or fire.
Running the power cord and the RGB cable close to each other can cause beat
noise. If this happens, keep the two separated so that beat noise is not generated.
If the projector is not be used for an extended period of time, disconnect the plug
from the power outlet. Do not unplug the power cable from the wall outlet under the
following circumstances, doing so may cause damage to the projector:
a) Immediately after the power cable is plugged into the wall outlet (the POWER 
indicator has not changed to a steady amber glow).
b) Immediately after the lamp has been switched off. After the projector is turned 
off with the POWER OFF button the cooling fan continues to operate for 3 
minutes while the Two Digit INDICATOR -- flashes.
c) While the hour glass icon or the message ‘Please wait a litttle’ is being displayed.
A—3
Overview
OVERVIEW
LBV00072; Revision A - 25/09/2001 
						

							Installation Advice
The projector should be placed on a flat, level surface and in a dry area free from
dust and moisture. Do not place the projector in direct sunlight, near heaters or heat
radiating appliances as exposure to direct sunlight, smoke or steam could harm 
internal components.
The projector should always be handled with care. Dropping or jarring the projector
could damage internal components.
Do not place heavy objects on the projector.
If you wish to have the projector installed on the ceiling do not attempt to install the
projector yourself. The projector must be installed in accordance with any local
building codes by qualified technicians in order to ensure proper operation and
reduce the risk of bodily injury.
The ceiling must be strong enough to support the weight of the projector.
Do not attempt to stack projectors on the ceiling.
A—4
Overview
OVERVIEW
LBV00072; Revision A - 25/09/2001
-
-
- 
						

							Part Names
A—5
0verview
Components
OVERVIEW
LBV00072; Revision A - 25/09/2001
Stacking Pad
Digital Input Terminal Panel
Remote Sensor
PC Card Slot
Lens (optional)
Input Terminal Panel
Ventilation (In)
FootRelease LeverVentilation (Out)Carrying Handle
Ventilation (In)
Ventilation (In) Controls Ventilation (In)AC Input Power Switch 
						

							Control Panel
The control panel at the rear of the projector provides all the main controls 
necessary to operate the projector.
1 - Power Button
Press to turn the projector on when the projector is in the standby condition (Main
Power switch must be on and the POWER indicator lit amber). Press and hold for 2
seconds to turn off the projector.
2 - Power LED
The power indicator is a dual colour LED. When the projector is on the indicator is
green. When the projector is in standby mode the indicator is amber.
After the projector is turned off, the indicator -- flashes for three minutes to
show that the cooling fan is working. Do not turn off the main power during that
time. After -- stops flashing, the POWER indicator will change to a steady
amber glow and the projector will be in the stand-by mode. The main power can
then be turned off.
3 - Status LED
When the projector is used with a configured switcher on SW1 level or SW2 level
mode, this indicator flashes when the projector is not connected with the switcher
correctly or when the switcher is turned off.
4 - Indicator Display
During normal operation the current projector ID (address) is shown in this two
digit display. In the event of an error, a projector error code will be displayed. The
display can be turned off using the ON/OFF Switch to the left hand side.
A—6
Overview
OVERVIEW
LBV00072; Revision A - 25/09/2001
8
POWER
LENS SHIFTFOCUSZOOM INDICATORSELECT ENTER
CANCELSTATUS ON
OFF MENU
-+ON/OFF+
75
4 2 Remote Sensor 9 10 11
6
1 3
- 
						

							5 - Enter Button
Executes your menu selection and activates items selected from the menu. When the
slidebar or dialog box is displayed: Pressing this button confirms adjustments/
setting and returns to the previous menu display.
6 - Cancel Button
Press this button to exit the menu. Press this button to return the adjustments to the
last condition while you are in the adjustment or setting menu.
7 - Select Cursor Buttons
The up & down cursor buttons are used to select the menu of the item you wish to
adjust and the left & right cursors change the level of a selected menu item.
8 - Menu Button
Activates the main menu.
9 - Zoom Button
Zoom the lens in and out.
10 - Focus Button
Adjust the lens focus.
11 - Lens Shift Cursor Buttons
Adjust the lens offset by shifting the projected image position horizontally and/or
vertically.
A—7
Overview
OVERVIEW
LBV00072; Revision A - 25/09/2001 
						

							Terminal Panel
The Terminal Panel located at the front of the projector provides all the required
connections for video, computer and remote control.
1 - INPUT 3 (RGB3)
A Mini D-Sub 15 pin connector to allow connection of a PC or other analogue RGB
equipment such as a high-definition document camera.
2 - OPTION IN/OUT
Two Mini D-Sub 9 pin connectors for system expansion such as PC-control. The IN 
A—8
Overview
OVERVIEW
LBV00072; Revision A - 25/09/2001
INPUT3
4
INPUT1
INPUT2 INPUT4
INPUT5
INPUT6
INPUT7
INPUT8 REMOTE2S-VIDEO1
VIDEO1 VIDEO2
S-VIDEO2 IN
OUTY
C
REMOTE1OPTION
IN
OUT
V H/HVB/CbG/Y R/Cr
RGB
V H/HVB/CbG/Y R/Cr
CbY Cr
5
1
2
3
76
910 8