Digital Projection Highlite 14000hd Users Manual

E-21
2
Installation
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
1 Installing the lens into the Projector ....................... E-22
Fitting the Lens holder ...................................................................................... E-22
Fitting the lens into the projector ...................................................................... E-22
2 Setting Up Your Projector ....................................... E-23
Screen Size and Projection Distance...

E-22
2. Installation
1 Installing the lens into the projector
NOTE: The lens must be installed by service personnel only.
Before installing the lens into the projector it is necessary to fit a
Lens Holder to the lens.
The lens holder is an adapter ring that is fixed to the lens which
provides a bayonet fixing required by the projector.
Fitting the Lens Holder
Remove the lens holders mounting screws
                     
Lens Holder
Place holder over lens  from the rear, aligning the grooves in the
lens...

E-23
Lens Unit which can be used on this equipment as standard condition.
This section describes how to set up your projector and how to
connect video and audio sources.
2 Setting Up Your Projector
Your Projector is simple to set up and use. But before you get
started, you must first:
1. Determine the image size
2. Set up a screen or select a non-glossy white wall onto which you can
project your image.
3. Install the optional lens to the projector.
NOTE: The lens must be installed by service personnel...

E-24
3 Lens Shift Adjustable Range
Lens Shift Adjustable Range for Desktop and Ceiling Mount Application The diagram below shows the location of the image position
in the lens. The lens can be shifted within the shaded area as shown using the normal projection position as a starting point.
Maximum Possible Range for L2K-12ZHB / L2K-14ZHB / L2K-18ZHB / L2K-22ZHB / L2K-30ZHB
Parenthesized values for the ceiling mount application
Up: 0.26 V (0.14 V) Right: 0.0 H (0.0 H)
Down: 0.14 V (0.26V) Left: 0.0 H (0.0...

E-25
AUDIO OUTLRComponent
COMPONENT
YCbCr
4 Making Connections
Connecting to the Image Input Terminals
This Projector has two interface boards, MM-VIDEO and MM-RGB as standard equipment. See page E-11. Connect required video
signals.
Four interface boards can be inserted in the Projector at the same time. See Page E-25.
Component video RCA3 cable
(not supplied)
RCA(female)-to-BNC(male)
adapter (not supplied)
2. Installation
BNC5 cable
(not supplied) Projector
PCDVD player
Information for Reducing...

E-26
Installing Additional Interface Boards
Four types of Interface boards are available for the Projector.
Please purchase as required.
1. Turn off the main power switch of the Projector.
Warning
Ensure main power is disconnected or by turning
off the main power switch before installing or re-
moving the board from the Projector. Failing to do
so could result in electrical shock.
2. Use a flat-bladed screwdriver to loosen the 2 screws of the slot panel
located at the input terminals portion of the...

E-27
2. Installation
Connecting to a Network
With the LAN connection, you can control the Projector over the network using a computer to turn the Projector on/off, select the
input and others.
Example of LAN connection
Using the HTTP Server function
1. Configure your LAN settings such as IP address on the Projector. (See
“LAN Mode” on page E-63)
Note
For the HL12000HD/10000HD, connect a ferrite core to the LAN cable on
the near side of the equipment.  For how to install the cerrite core see
page...

E-28
2. Installation
Connnecting the Power Cable
After making certain that the main power switch of your projector is OFF, connect the power cable to a 200 to 240 VAC three-prong
outlet (grounded).
Two versions of the projector are available: USA models are supplied with a Hubbel type connector, for Rest of World a CEE-Form
connector is supplied.
CAUTION
• Please contact your dealer / distributor to perform the wiring for connection of the power cable to your projector.
• Be sure to ground the equipment...

E-29
Removing the PC Card
Press the eject button slowly. The eject button card pops out a
little. Press the eject button slowly again. Grasp the edges of
the PC card and pull it out. Push and insert the eject button
fully until it stops.
NOTE: Do not eject the PC card while its data is being accessed.
CAUTION: Make sure that the PC card or wireless LAN card is
removed during Standby mode or with the main power off.Failure
to do so may cause damage to the data on your PC card or
wireless LAN card, or may...

E-30
3
Projecting an Image
(Basic Operation)
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
1 Turning on the Projector ........................................ E-31
2 Selecting a Source ................................................ E-32
3 Adjusting the Picture Size and Position ................. E-32
4 Optimizing RGB Picture Automatically .................. E-34
5 Turning off the Projector ........................................ E-34