Digital Projection Highlite 12000dsx+, 8000dsx+ Users Manual

E-61
Lens Shutter on During Signal Switching
While switching the signals (screen image is muted), the light
can be absolutely shut out from the lens simultaneously with
shutter.
With Check Mark ................. While switching the signals and
muting the images, shutter is
simultaneously activated.
Without Check Mark ............ While switching the signals and
muting the images, shutter is
deactivated.
3D Sequence Set Select
Use when displaying 3D images using a single projector OR
signals with a high...

E-62
Auto ............. Searches for an active source in order of Slot 1
→ Slot 2 → Slot 3 → Slot 4 → Slot 1 and dis-
plays the first found source.
Select .......... Displays the selected source input every time the
Projector is started up. Select an input from the
pull-down menu.
Disabling the Cabinet Buttons [Control Panel Key Lock]
This option turns on or off the Control Panel Key Lock func-
tion.
NOTE:
•This Control Panel Key Lock does not affect the remote control functions.
•When the cabinet...

E-63
Gateway ......Set the default gateway of the network connected
to the Projector. Press H to display the software
keyboard and type in 12 numeric characters.
Checking this box will make the set default route
valid.
When data is sent from the LAN card, the trans-
fer location will be searched according to the pre-
viously set routing information; however, when
the transfer location has not been found as a
result of the search, the data will be sent to the
device that holds the IP address set here....

E-64
6. Using On-Screen Menu
Key1-4:
Enter encryption key when selecting [64bit] or [128bit] in [WEP].
Up to 5 characters can be set in 64 bit and up to 13 characters
in 128 bit. Press the “HEX” button to change to “ASCII” to set
the key in ASCII digit. You can toggle this button between
“ASCII” and “HEX”.
The key can also be set in hexadecimal digit.
*Hexadecimal uses 0 to 9 and A to F.
*Up to 10 characters can be set in 64 bit and up to 26
characters in 128 bit.
NOTE: Only numbers can be entered when...

E-65
6. Using On-Screen Menu
Image Mode
Installation of the MM-IMGPRO and MM-SCALING options per-
mits the instantaneous switching of signals between two input
interface boards when “Seamless” of the “Image Mode” is se-
lected.
•Seamless Mode - active
- Select an input
-  Wait for “Transition Ready” to be displayed on the LCD screen
- Press the ENTER button to display the input.
- Next input appears immediately.
•Seamless operates between left and right input slots. The solid
lines in the following...

E-66
4. Use the Software keyboard to type “5555”.
Highlight “OK” on the “Password” entry screen and then press the EN-
TER button.
The “Delete Password. Are you sure? Yes/No” dialog box will be dis-
played.
5. Use the SELECT 
F or E button to highlight “Yes” and press the EN-
TER button.
Your password will be deleted.
Security
The Security function enables you to protect your projector so
that the projector will not project a signal unless you enter a key-
word. There is also an option to lock the...

E-67
•The security disable mode is maintained until the main power is turned
off (by setting the main power switch to O or unplugging the power
cable).
In the following cases you will be asked to check the protect key or
input the keyword:
(1) When OK is selected at an image for which security is set and
the power is turned off then back on
(2) When the main power is turned off then back on while the security
function is enabled
(3) When you attempt to display an image for which security is set
while the...

E-68
3. Select “Edit” and press the ENTER button to open the Edit window.
4. Set the Day, Time (24 hours format), On-Time and Off-Time using the
SELECT buttons and the Software keyboard (1 thru 10).
5. Select On Timer or Off Timer
6. Repeat the Timer
To repeat the On Timer or Off Timer program every week, place a check
mark in “Repeat”.
7. Select “OK” and press the ENTER button on the remote control to com-
plete the setting. To cancel this and return to its previous screen, select
“Cancel”.
NOTE: If...

E-69
Enabling Sleep Timer
1. Select your desired time between 30 minutes and 16 hours: Off, 0:30,
1:00, 2:00, 4:00, 8:00, 12:00, 16:00.
2. Select “Set” and press the ENTER button on the remote control.
3. The remaining time starts counting down.
4. The projector will turn off after the countdown is complete.
NOTE:
•To cancel the preset time, set Off for the preset time or turn off the power.
•When the remaining time reaches 3 minutes before the projector is turned off,
the Projector will turn off in 3...

E-70
Page 2
Signal Type, Video Type, Sync Type, Interlace, Direct Key
Projector Information
Displays the information for your Projector such as Remaining
Lamp Time, Lamp Hour Meter, Projector Usage, Projector ID,
version number and others. This dialog box has five pages.
Page 1
Remaining Lamp Time, Lamp Hour Meter, Projector Usage, Pro-
jector ID
NOTE: Nothing is displayed on the item, “Serial Number”. Please confirm the serialnumber on label attached on the projector itself.
Page 2
Version...