Dell St2310 Users Guide

							  LCD Conditioning  
Factory Reset  
Back        
If an image appears to be retained on the monitor, select  LCD Conditioning  to help eliminate any image retention. Using the LCD Conditioning feature may take several hours. Severe 
cases of image retention are known as burn - in, the LCD Conditioning feature does not remove burn - in. 
 
   
Reset all OSD settings to the factory default settings.
Press the   button to go back to or exit the main menu.
  Personalize   There are 2 shortcut keys on the front panel. Select one control menu for each shortcut key to allow direct access.   
						

							   
OSD Warning Messages  
When the monitor does not support a particular resolution mode you will see the following message :
or
This means that the monitor cannot synchronize with the signal that it is receiving from the computer. See  Monitor Specifications  for the Horizontal and Vertical frequency ranges addressable by this 
monitor. The recommended mode is  1920x1080.  
 
When monitor enters Power Save mode, the following message appears :  
or
Activate the computer and wake up the monitor to gain access to the  OSD
   
   
If you press any button other than the power button the following message will appear:
or
     
						

							   
   
   
   
   
    
   
   
See  Solving Problems  for more information.   
Setting the Maximum Resolution  
 
To set the maximum resolution for the monitor.  
1. Right - click on the desktop and select  Properties .   
2. Select the  Settings  tab.   
3. Set the screen resolution to 1920 x 1080.   
4. Click  OK .   
If you do not see 1920 x 1080 as an option, you may need to update your graphics driver. Depending on your computer, complete one of the following 
procedures.  
 
If you have a Dell desktop or portable computer:   
Go to  support.dell.com , enter your service tag, and download the latest driver for your graphics card.   
If you are using a non - Dell computer (portable or desktop):  
Go to the support site for your computer and download the latest graphic drivers.   
Go to your graphics card website and download the latest graphic drivers.   
Using the Dell Soundbar (Optional)  
The Dell Soundbar is a stereo two channel system mountable on Dell flat panel displays. The Soundbar has a capacitive touch front control panel, a white LED 
for power indication, and two audio headset jacks.  
 If  VGA/DVI/HDMI  input is selected and both  VGA, DVI and HDMI  cable are not connected, a floating dialog box as shown 
below appears.
or
     
						

							 
   
Using the Tilt  
Tilt  
With the built - in pedestal, you can tilt the monitor for the most comfortable viewing angle.  
 
 
Back to Contents Page  1. Attach mechanism 
2.   Headphone connectors 
Power indicator 
4.   Power/Volume control
NOTE:   The base is detached when the monitor is shipped from the factory.   
						

							Back to Contents Page   
 
Setting Up Your Monitor   
 
Important instructions to set the display resolution to 1920x1080 (Maximum)  
For optimal display performance while using the Microsoft Windows ®  operating systems, set the display resolution to 1920 x 1080 pixels by performing the 
following steps:  
1. Right - click on the desktop and click  Properties .  
2. Select the  Settings  tab.  
3. Move the slider - bar to the right by pressing and holding the left - mouse button and adjust the screen resolution to  1920x1080 .  
4. Click  OK .  
    If you do not see  1920x1080  as an option, you may need to update your graphics driver. Please choose the scenario below that best describes the 
computer system you are using, and follow the provided directions:  
1:  If you have a Dell  desktop or a Dell  portable computer with internet access.  
2:  If you have a non Dell  desktop, portable computer, or graphics card.  
   
Back to Contents Page     
						

							 
   
   
Information in this document is subject to change without notice.  
 
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.   is strictly forbidden.  
Trademarks used in this text:  Dell  and the  DELL  logo, are trademarks of Dell Inc.  Microsoft  and  Windows  are either registered trademarks or trademarks of Microsoft Corporation in 
the United States and/or other countries.  ENERGY STAR  is a registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has 
determined that this product meets the ENERGY STAR guidelines for energy efficiency.    
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any 
proprietary interest in trademarks and trade names other than its own.  
ST2210b/ST2310f/ST2410b  
June  2009         R ev.  A00      User Guide  
  Important instructions to set the display resolution to 1920x1080 (Maximum)    
						

							Back to Contents Page    
   
Setting Up the Monitor   
Users Guide  
   Attaching the Base  
   Connecting the Monitor  
   Attaching the Soundbar (Optional)  
   Removing the Base  
   
Attaching the Base  
 
   
Complete the following steps to attach the base.  
1. Place the monitor on a soft cloth or cushion.   
2. Attach the base to the monitor.   
3. Tighten the screw located below the stand.   
Connecting the Monitor  
To connect your monitor to the computer perform the following steps/instructions:  
1. Turn off your computer and disconnect the power cable.    
2. Connect the HDMI cable, white (digital DVI - D), or blue (analog VGA) display connector cable to the corresponding video port on the back of your 
computer. Do not use all the cables on the same computer.  Use all of the  cables only when they are connected to different computers with appropriate 
video systems.   
   
Connecting the blue VGA cable  
 NOTE:  The base is detached when the monitor is shipped from the factory.  
CAUTION:   Before you begin any of the procedures in this section, follow the  safety instructions .  
						

							Connecting the White DVI Cable *  
 
Connecting the HDMI Cable *  
 
After you have completed connecting the VGA/DVI/HDMI cable, follow the procedure below to complete your monitor setup:  
1. Plug the power cables for your computer and monitor into a nearby outlet.    
2. Turn on the monitor and the computer.  
If your monitor displays an image, installation is complete. If it does not display an image, see  Solving Problems .    
Attaching the Soundbar (Optional)  
 
Removing the Base  NOTE:  *Optional purchase item. To purchase DVI or HDMI cable, please visit Dell.com
NOTE:  The Graphics are used for the purpose of illustration only. Appearance of the the computer may vary.
1. Working from the rear of the monitor, attach the Soundbar by aligning the two slots with the two tabs along the bottom rear of the monitor.
2. Slide the Soundbar to the left until it snaps into place.
Connect the  S oundbar with the DC power connector.
4. Insert the mini stereo plug from the rear of the Soundbar into the computers audio output jack or the monitors audio output jack.
NOTICE:  Do not use with any device other than the Dell Soundbar.  
						

							 
After placing the monitor panel on a soft cloth or cushion, complete the following steps to remove the base.  
1. Loosen the screw  on the bottom of the base.   
2. Detach the base away from the monitor.   
   
Back to Contents Page  
     
						

							Back to Contents Page    
 
Solving Problems    
 
   Self - Test  
   Built - in Diagnostics  
   Common Problems  
   Product - Specific Problems  
   Troubleshooting the Dell™ Soundbar (Optionalyf   
   
   
   
Self - Test  
Your monitor provides a self - test feature that allows you to check whether your monitor is functioning properly. If your monitor and computer are properly 
connected but the monitor screen remains dark, run the monitor self - test by performing the following steps:   
1. Turn off both your computer and the monitor.   
2. Unplug the video cable from the back of the computer. To ensure proper Self - Test operation, remove the Analog (blue connector) cable from the back of 
computer.   
3. Turn on the monitor. 
  
   
4. This box also appears during normal system operation, if the video cable becomes disconnected or damaged.   
5. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.   
If your monitor screen remains blank after you have performed Step 5, check your video controller and computer system.  
Built - in Diagnostics  
Your monitor has a built - in diagnostic tool that helps you determine if the screen abnormality you are experiencing is an inherent problem with your monitor, or 
with your computer and video card.  
To run the built - in diagnostics:  
1. Ensure that the screen is clean (no dust particles on the surface of the screen).   
2. Unplug the video cable(s) from the back of the computer or monitor. The monitor then goes into the self - test mode.   
3. On the front panel, press and hold the  shortcut button 1  and  shortcut button 4  keys on the front panel, simultaneously for 2 seconds. A gray screen 
appears.   CAUTION:  Before you begin any of the procedures in this section, follow the  Safety Instructions .  
The floating dialog box should appear on - screen (against a black background) if the monitor cannot sense a video signal and is working correctly. 
While in self - test mode, the power LED remains white. Also, the dialog shown below will continuously scroll through the screen.  
or
   
NOTE:  You can run the built - in diagnostics only when the video cable is unplugged and the monitor is in  self - test mode .