Dell S300 Projector Users Guide

Using Your Projector41
3D DISPLAY—Select On to start the 3D display function. Default is Off.
 
NOTE: To activate 3D Display function, ensure that 3D goggles, 3D video 
contents and 60Hz/120Hz signal output graphic card supported on PC/NB are 
ready. 
3D Sync Invert—
If you see a discrete or overlapping image while 
wearing DLP 3D goggles, you may need to execute Invert to get 
best match of left/right image sequence to get the correct image. 
(For DLP 3D goggles)
Network—Select On to activate network...

42Using Your Projector
IP ADDRESS—Automatically or manually assigns the IP address to the projector 
connected to the network.
S
UBNET MASK—Configure the Subnet Mask of the network connection.
G
ATEWAY—Check the Gateway address with your network/system administrator if 
you configure it manually.
DNS—Check the DNS Server IP address with your network/system administrator 
if you configure it manually.
S
TORE—Press   to save the changes made in network configuration settings.
 
NOTE: 
1Use   and   button...

Using Your Projector43
OTHERS
The Others menu allows you to change settings for Menu, Screen, Audio, Power, 
Security, and Closed Caption (for NTSC only). You can also perform Test Pattern 
and Factory Reset.
MENU SETTINGS—Select and press   to activate menu settings. The menu 
settings consists of the following options:
MENU POSITION—Allows you to change the position of the OSD menu on 
the screen.
MENU TRANSPARENCY—Select to change the transparency level of the OSD 
background.
MENU TIMEOUT—Allows you...

44Using Your Projector
SCREEN SETTINGS—Select and press   to activate screen settings. The screen 
settings menu consists of the following options:
CAPTURE SCREEN—Select and press   to capture the screen display, the 
following message appears on the screen.
 
NOTE: To capture a full image, ensure the input signal that is 
connected to the projector is 1024 x 768 resolution.
SCREEN—Select Dell to use the Dell logo as wallpaper. Select Captured to 
set the captured image as wallpaper.
RESET—Select and...

Using Your Projector45
POWER SETTINGS—Select and press   to activate power settings. The power 
settings menu consists of the following options:
POWER SAVING—Select Off to disable Power Saving mode. By default, the 
projector is set to enter power saving mode after 120 minutes of no activity. 
A warning message appears on screen showing a 60-second countdown 
before switching to power saving mode. Press any button during 
countdown period to stop power saving mode.
You can also set a different delay...

46Using Your Projector
PASSWORD—When Password Protect is enabled, a Password Protect screen 
requesting you to enter a password will be displayed when the power plug is 
inserted into the electrical outlet and the power for the projector is first 
turned on. By default, this function is disabled. You can enable this feature 
by selecting Enabled. If the password has been set before, key in the 
password first and select the function. This password security feature will 
be activated the next time you...

Using Your Projector47
2If you have entered an incorrect password, you will be given 
another 2 chances. After the three invalid attempts, the projector 
will automatically turn off.
 NOTE: If you forget your password, contact DELL™ or qualified service 
personnel.
3
To disable the password function, select Off to disable the 
function.
4To delete the password, select Delete. 

48Using Your Projector
CHANGE PASSWORD—Key in the original password, then enter the new 
password and confirm the new password again.
CLOSED CAPTION—Select On to enable close caption and activate the closed 
caption menu. Select an appropriate closed captions option: CC1, CC2, CC3, and 
CC4. 

Using Your Projector49
 NOTE: Closed caption option is available for NTSC only.
TEST PATTERN—Test Pattern is used to test focus and resolution.
You can enable or disable the Te s t  Pa t t e r n by selecting Off, 1 or 2. You can also 
invoke the Te s t  Pa t t e r n  1 by pressing and holding down   and   buttons on the 
control panel simultaneously for 2 seconds. You can also invoke the test pattern 2 
by pressing and holding down   and   buttons on the control panel 
simultaneously for 2 seconds....

50Using Your Projector
Managing the Projector From Web 
Management
Configuring the Network Setting
If the projector is connected to a network, you can access the projector using a web 
browser by configuring the network setting (TCP/IP). When using the network 
function, the IP address should be unique. For configuring the network setting, 
refer to Network on page 41.
Accessing Web Management
Use Internet Explorer 5.0 and above or Firefox 1.5 and above and enter the IP 
address. You can now access Web...