Dell Projector 1610HD User Manual

							Using Your Projector51
Projector Status and Control Page
•Projector Status: There are 5 status: Lamp On, Standby, Power Saving, 
Cooling and Warming up. Click the Refresh button to refresh the status and 
control settings.
•Po w e r  S a v i n g: Power Saving can be set to Off, 30, 60, 90, or 120 minutes. 
Refer to page 43.
•Alert Status: There are 3 error status: Lamp warning, Low lamp life, and 
Temperature warning. Your projector might lock up in protection mode if 
any of the alerts is activated. To exit protection mode, click the Clear button 
to clear the Alert Status before you could Power ON your projector.
•Projector Mode: Allows you to select the projector mode, depending upon 
how the projector is mounted. There are 4 projection modes: Front 
Projection-Desktop, Front Projection-Ceiling Mount, Rear Projection-
Desktop and Rear Projection-Ceiling Mount
•Source Select: The Source Select menu allows you to select your projector 
input source. You can select VGA-A, VGA-B, S-V
IDEO, COMPOSITE VIDEO, 
and HDMI. 
•Video Mode: Select a mode to optimize the display image based on how the 
projector is being used:
 - Presentation: Best for presentation slides. 
						

							52Using Your Projector
 - Bright: Maximum brightness and contrast.
 - 
Movie: For viewing movie & photo.
 - 
sRGB: Provide a more accurate color representation.
 - 
Custom: User preferred settings.
•Blank Screen: You can select On or Off.
•Aspect Ratio: Allows you to select the aspect ratio to adjust how the image 
appears.
•Brightness: Select value 
to adjust the brightness of the image.
•Contrast: Select value to adjust the display contrast.
•Audio Input: You can select Audio-A, Audio-B, HDMI and Microphone for 
the input source
•Vo l u m e: You can select the value (0~20) for the audio volume
•Speaker: You can select On to enable the audio function or select Off to 
disable the audio function. 
						

							Using Your Projector53
E-mail Alert
• E-mail Alert: You can set whether to be notified by email (Enable) or not 
(Disable).
•To/CC/From: You can enter email address of sender (From) and recipients 
(To/Cc) to receive notification when an abnormality or warning occurs.
• Alert Condition: You can select the abnormalities or warnings to be notified 
by email. When any of the alert conditions occur, an email will be sent to 
the recipients (To/Cc).
•Out going SMTP server, User name and Password should be provided by 
your network administrator or MIS. 
						

							54Using Your Projector
Password Setting
Use Password Setting to set up an administrator password to access the We b  
Management. When enabling password for the first time, set the password before 
enabling it. When the password function is enabled, the administrator password 
will be required for accessing the Web Management.
•New Password: Enter new password
•Confirm Password: Enter password again and submit
•Write Community: Set security for SNMP. Enter password and submit.
 
NOTE: Contact Dell if you forget your administrator password. 
						

							Using Your Projector55
Login Page
•Administrator Password: Enter the Administrator Password and click Login. 
						

							56Using Your Projector
Firmware Update
Use the Firmware Update page to update your projector’s firmware. Press Update 
to start.
• Please wait till the count reaches 0. 
						

							Using Your Projector57
• Wait for 3 seconds and it will proceed to the next step automatically.
• Select the file to upgrade and click the Upgrade button. When upgrading is 
in progress, the Cancel button is disabled. 
						

							58Using Your Projector
• Please wait till the count reaches 0.
• When upgrade is complete, please click the ReLogin button to go back to 
the Web Management Home Page. 
						

							Using Your Projector59
TIPS:
I would like remote access the 
projector via Internet. What is 
the better setting for the 
browser?To have a better setting for the browser, please 
follow the steps below:
1Open Control Panel  Internet Options  
General tab   Te m p o r a r y  I n t e r n e t  F i l e s  
Settings  Select Every visit to the pages.
2Some firewall or anti-virus may block the 
HTTP application, if possible turn off the 
firewall or anti-virus.
I would like to remote access the 
projector via Internet. What 
socket port number should I 
open for it in the firewall?The following are TCP/IP socket ports which 
projector uses.
Why am I unable to access the 
projector via Internet?
1Check whether your computer/laptop is 
connected to the Internet.
2Check with your MIS or network 
administrator whether your computer/laptop 
is in the same subnet.
UDP/TCPPort 
NumberDescription
TCP 80 Web configuration 
(HTTP)
UDP/TCP 25 SMTP: used for email 
routing between mail 
servers
UDP/TCP 161 SNMP: Simple 
Network Management 
Protocol
UDP 9131 AMX: used for AMX 
discovery 
						

							60Using Your Projector
Why am I unable to access the 
SMTP server?1Check with your MIS or network 
administrator whether the SMTP server 
function is open for the projector and the IP 
assigned to the projector is allowed to access 
the SMTP server. The projector’s SMTP 
socket port number is 25, this cannot be 
changed.
2Check if the out going SMTP server, user 
name, and password are set correctly.
3Some SMTP servers will check whether the 
mail address of From correlates with the 
User name and Password. For example, 
you use [email protected]
 as the mail address in 
From. You should also use [email protected]
 
account information for the User name and 
the password to log in the SMTP server.
Why am I unable to receive the 
test alert email even though the 
projector already indicates the 
test mail is already sent?It could be because the SMTP server 
recognized the alert mail as a spam mail or 
because of the SMTP server restriction. Check 
with your MIS or network administrator for 
the SMTP server’s setting.