Dell M5030 Service Manual

   
7. Lift the processor module from the ZIF socket.   
 
Replacing the Processor Module   
   
1. Follow the instructions in  Before You Begin .   
 
     
2. Align the pin - 1 corner of the processor module with the pin - 1 corner of the ZIF socket, then insert the processor module.   
 
When the processor module is properly seated, all four corners are aligned at the same height. If one or more corners of the module are higher than the 
others, the module is not seated properly.  
   
   
3. Tighten...

Back to Contents Page    
 Processor Heat Sink   
 
   Removing the Processor Heat Sink   
   Replacing the Processor Heat Sink   
 
   
   
   
Removing the Processor Heat Sink   
   
1. Follow the instructions in  Before You Begin .   
 
     
2. Remove the battery (see  Removing the Battery ).   
 
     
3. Remove the keyboard (see  Removing the Keyboard ).   
 
     
4. Remove the palm rest (see  Removing the Palm Rest ).   
 
     
5. Remove the adhesive tape that secures the display cable to the...

   
Replacing the Processor Heat Sink   
   
1. Follow the instructions in  Before You Begin .   
 
     
2. Place the processor heat sink on the system board.   
 
     
3. Align the four captive screws on the processor heat sink with the screw holes on the system board and tighten the screws in sequential order (indicated 
on the processor heat sink).   
 
   
4. Route the cables through the routing guides. Connect the fan cable and display cable to their connectors on the system board.   
 
     
5....

Back to Contents Page    
 Display   
 
   Display Assembly   
   Display Bezel   
   Display Panel   
 
   
   
   
Display Assembly   
   
Removing the Display Assembly  
   
1. Follow the instructions in  Before You Begin .   
 
     
2. Remove the battery (see  Removing the Battery ).   
 
     
3. Remove the keyboard (see  Removing the Keyboard ).   
 
     
4. Remove the two screws that secure the display assembly to the base of the computer.   
 
   
   
5. Remove the palm rest (see  Removing the...

   
   
Replacing the Display Assembly  
   
1. Follow the instructions in  Before You Begin .   
 
     
2. Place the display assembly in position and replace the two screws (one on each side) that secure the display assembly to the computer base.   
 
     
3. Route the display cable into the routing guide and connect the display cable to the connector on the system board.   
 
     
4. Route the Mini - Card antenna cable into the routing guide and connect the Mini - Card antenna cable to the connector...

   
   
Replacing the Display Bezel  
   
1. Follow the instructions in  Before You Begin .   
 
     
2. Align the display bezel over the display panel, and gently snap it into place.   
 
     
3. Replace the display assembly (see  Replacing the Display Assembly ).   
 
Display Panel   
   
Removing the Display Panel  
   
1. Follow the instructions in  Before You Begin .   
 
     
2. Remove the display assembly (see  Removing the Display Assembly ).   
 
     
3. Remove the display bezel (see...

   
6. Lift the display panel off the display cover.   
 
     
7. Turn the display panel over and place it on a clean surface.   
 
     
8. Lift the tape that secures the display cable to the display board connector and disconnect the display cable.   
 
     
9. Peel off the camera cable from the back of the display panel.   
 
   
   
10. Remove the four screws (two on each side) that secure the display panel brackets to the display panel.   
 
   
   
Replacing the Display Panel  
   
1. Follow the...

2. Replace the four screws (two on each side) that secure the display panel brackets to the display panel.   
 
     
3. Connect the display cable to the display board connector and secure it with the tape.   
 
     
4. Adhere the camera cable to the back of the display panel.   
 
     
5. Place the display panel on the display cover and connect the camera cable to the connector on the camera module.   
 
     
6. Align the screw holes on the display panel with the screw holes on the display cover....

Back to Contents Page    
 Hard Drive   
 
   Removing the Hard Drive   
   Replacing the Hard Drive   
 
   
   
   
   
   
Removing the Hard Drive   
   
1. Follow the instructions in  Before You Begin .   
 
     
2. Remove the battery (see  Removing the Battery ).   
 
     
3. Remove the keyboard (see  Removing the Keyboard ).   
 
     
4. Remove the two screws that secure the hard drive to the base of the computer.
   
 
 
     
5. Remove the palm rest (see  Removing the Palm Rest )....

   
Replacing the Hard Drive   
   
1. Follow the instructions in  Before You Begin .   
 
     
2. Remove the new hard drive from its packaging.  
Save the original packaging for storing or shipping the hard drive.   
 
     
3. Place the hard drive in the hard - drive bay and push the hard drive towards the connector until it is fully seated.   
 
     
4. Turn the computer over and replace the two screws that secure the hard -  drive to the base of the computer.   
 
     
5. Replace the palm rest...