dell latitude d800 User Manual

							Display Assembly: Dell Latitude D800 Service Manual
Display Bezel
 CAUTION: Before performing the following procedures, read the safety 
instructions in your System Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist 
grounding strap or by periodically touching an unpainted metal surface (\
such as 
the back panel) on the computer. 
1.  Follow the instructions in 
Preparing to Work Inside the Computer. 
2.  Remove the 
central control cover. 
3.  Remove the 
display assembly. 
4.  Use a plastic scribe to pry the eight display bumpers out of the screw h\
oles  located on the front of the bezel. 
5.  Remove the eight M2.5 x 6-mm screws located on the front of the bezel. 
NOTICE: Carefully separate the bezel from the top cover to avoid damage to 
the bezel. 
6.  Starting at the bottom of the display panel (by the Dell™ logo), us\
e your fingers  to separate the bezel from the top cover by lifting the inside edge of t\
he bezel 
away from the top cover. 
Display Panel
 CAUTION: Before performing the following procedures, read the safety 
instructions in your System Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist 
grounding strap or by touching an unpainted metal surface on the compute\
r. 
1.  Follow the instructions in 
Preparing to Work Inside the Computer. 
file:///F|/Service%20Manuals/Dell/Latitude/d800/display.htm (5 of 8) [\
2/28/2004 8:17:48 AM] 
						

							Display Assembly: Dell Latitude D800 Service Manual
2.  Remove the central control cover. 
3.  Remove the 
display assembly. 
4.  Remove the 
display bezel. 
5.  Remove the nine M2 x 3-mm screws from the display panel. 
6.  Lift the display panel, and rotate the display panel out of the top cove\
r. 
7.  Remove the yellow tape from the top display connector. 
8.  Press in the tabs on both sides of the top display-cable connector, and \
pull the  display cable connector away from the top flex-cable connector. 
 
1 top flex-cable connector
2 top display-cable 
connector
file:///F|/Service%20Manuals/Dell/Latitude/d800/display.htm (6 of 8) [\
2/28/2004 8:17:48 AM] 
						

							Display Assembly: Dell Latitude D800 Service Manual
3tabs
9.  Use the pull-tab to disconnect the bottom flex-cable connector from the \
inverter  connector. 
 
1 top flex-cable connector
2 top display-cable 
connector
3 pull-tab on bottom flex-
cable connector
10.  Remove the yellow tape from above the bottom flex-cable connector. 
Back to Contents Page
file:///F|/Service%20Manuals/Dell/Latitude/d800/display.htm (7 of 8) [\
2/28/2004 8:17:48 AM] 
						

							Display Assembly: Dell Latitude D800 Service Manual
 
file:///F|/Service%20Manuals/Dell/Latitude/d800/display.htm (8 of 8) [\
2/28/2004 8:17:48 AM] 
						

							Video Card: Dell Latitude D800 Service Manual
Back to Contents Page 
Video Card 
Dell™ Latitude™ D800 Service Manual
 CAUTION: Before performing the following procedures, read the safety 
instructions in your System Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist 
grounding strap or by periodically touching an unpainted metal surface (\
such as 
the back panel) on the computer. 
1.  Follow the instructions in 
Preparing to Work Inside the Computer. 
2.  Remove the 
keyboard. 
3.  Remove the 
display. 
4.  Remove the four M2.5 x 6-mm screws from the video card. 
 
file:///F|/Service%20Manuals/Dell/Latitude/d800/video.htm (1 of 2) [2/\
28/2004 8:17:48 AM] 
						

							Video Card: Dell Latitude D800 Service Manual
1M2.5 x 6-mm screws (4)
2 video card
5.  Lift the video card out of the computer. 
Back to Contents Page
 
file:///F|/Service%20Manuals/Dell/Latitude/d800/video.htm (2 of 2) [2/\
28/2004 8:17:48 AM] 
						

							Microprocessor Thermal-Cooling Assembly: Dell Latitude D800 Service Manu\
al
Back to Contents Page 
Microprocessor Thermal-Cooling 
Assembly 
Dell™ Latitude™ D800 Service Manual
Removing the Microprocessor Thermal-Cooling 
Assembly 
 CAUTION: Before performing the following procedures, read the safety 
instructions in your System Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist 
grounding strap or by periodically touching an unpainted metal surface (\
such as 
the back panel) on the computer. 
NOTICE: Disconnect the computer and any attached devices from electrical 
outlets, and remove any installed batteries. 
1.  Follow the instructions in 
Preparing to Work Inside the Computer. 
2.  Remove the 
keyboard. 
3.  Remove the 
fan. 
NOTE: You can remove the microprocessor thermal-cooling assembly with the 
fan attached. 
4.  Loosen in consecutive order the four captive screws, labeled 1 through\
 4,  that secure the microprocessor thermal-cooling assembly to the system bo\
ard. 
file:///F|/Service%20Manuals/Dell/Latitude/d800/thermal.htm (1 of 3) [\
2/28/2004 8:17:49 AM] 
						

							Microprocessor Thermal-Cooling Assembly: Dell Latitude D800 Service Manu\
al
 
1 captive screws (4)
2 microprocessor thermal-
cooling assembly
5.  Rotate the microprocessor thermal-cooling assembly up toward the side of\
 the  computer and away from the system board. 
file:///F|/Service%20Manuals/Dell/Latitude/d800/thermal.htm (2 of 3) [\
2/28/2004 8:17:49 AM] 
						

							Microprocessor Thermal-Cooling Assembly: Dell Latitude D800 Service Manu\
al
 
Installing the Microprocessor Thermal-Cooling 
Assembly 
1.  Place the left side of the microprocessor thermal-cooling assembly under\
 the palm rest and rotate the assembly onto the system board. 
2.  Tighten the four captive screws, labeled 1 through 4, in consecutive\
 order. 
Back to Contents Page
 
file:///F|/Service%20Manuals/Dell/Latitude/d800/thermal.htm (3 of 3) [\
2/28/2004 8:17:49 AM] 
						

							Palm Rest: Dell Latitude D800 Service Manual
Back to Contents Page 
Palm Rest 
Dell™ Latitude™ D800 Service Manual
 CAUTION: Before performing the following procedures, read the safety 
instructions in your System Information Guide.
NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist 
grounding strap or by periodically touching an unpainted metal surface (\
such as 
the back panel) on the computer. 
1.  Follow the instructions in 
Preparing to Work Inside the Computer. 
2.  Remove the 
keyboard. 
NOTICE: You must remove the display assembly before you remove the palm 
rest; the display hinges pass through the back of the palm rest. 
3.  Remove the 
display assembly. 
4.  Remove the 
mircoprocesser thermal-cooling assembly. 
5.  Remove the 
video card. 
6.  Remove the 13 M2.5 x 12-mm screws from the bottom of the computer. 
file:///F|/Service%20Manuals/Dell/Latitude/d800/palmrest.htm (1 of 4) \
[2/28/2004 8:17:50 AM]