Home > Dell > Notebook > dell latitude c400 User Manual

dell latitude c400 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual dell latitude c400 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 327 Dell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Display Assembly and Display Latch : Dell Latitude C400 Service Manual 
     
    1 M2.5 x 6-mm screws (2)
    6.  Turn the computer right-side up and open the display 180 degrees. 
    Display Assembly 
    file:///F|/Service%20Manuals/Dell/Latitude/c400/display.htm (2 of 5) [\
    2/28/2004 7:51:02 AM] 
    						
    							Display Assembly and Display Latch : Dell Latitude C400 Service Manual 
     
    1 display-feed flex cable
    2 M2.5 x 12-mm screws (2)
    3 display-feed flex cable hold-down board
    4 pull tab
    7.  Remove the two M2.5 x 12-mm screws from the display-feed flex cable hold\
    -down board. 
    8.  Use the pull tab to disconnect the display-feed flex cable from its conn\
    ector on the system  board. 
    9.  Move the display assembly to an upright position and pull it up out of t\
    he computer. 
    file:///F|/Service%20Manuals/Dell/Latitude/c400/display.htm (3 of 5) [\
    2/28/2004 7:51:02 AM] 
    						
    							Display Assembly and Display Latch : Dell Latitude C400 Service Manual 
    Replacing the Display Latch
    NOTICE: Disconnect the computer and any attached devices from electrical outlets\
    , and 
    remove any installed batteries. 
    NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by tou\
    ching 
    an unpainted metal surface on the computer. 
    NOTICE: Read Preparing to Work Inside the Computer before performing the following 
    procedure. 
    To replace the display latch, you must replace the whole bezel. 1.  Remove the battery. 
    2.  Remove the 
    hard drive. 
    3.  Open the display 180 degrees, and remove the six rubber screw covers and\
     the six  M2 x 4-mm screws that secure the bezel. 
    Bezel Removal 
     
    1 bezel
    file:///F|/Service%20Manuals/Dell/Latitude/c400/display.htm (4 of 5) [\
    2/28/2004 7:51:02 AM] 
    						
    							Display Assembly and Display Latch : Dell Latitude C400 Service Manual 
    2display latch
    3 M2 x 4-mm screw (6)
    4 display assembly
    4.  Use a small flat-blade screwdriver to carefully pry around the perimeter\
     of the bezel until  the bezel separates from the display assembly. 
    5.  Install the new bezel. 
    Back to Contents Page
     
     
     
    file:///F|/Service%20Manuals/Dell/Latitude/c400/display.htm (5 of 5) [\
    2/28/2004 7:51:02 AM] 
    						
    							Palm Rest : Dell Latitude C400 Service Manual 
    Back to Contents Page 
    Palm Rest 
    Dell™ Latitude™ C400 Service Manual 
      Removing the Palm Rest
      Replacing the Palm Rest
    Removing the Palm Rest
    NOTICE: Disconnect the computer and any attached devices from electrical 
    outlets, and remove any installed batteries. 
    NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by 
    touching an unpainted metal surface on the computer. 
    NOTICE: Read Preparing to Work Inside the Computer before performing the 
    following procedure. 
    1.  Remove the 
    hard drive. 
    2.  Remove the 
    keyboard. 
    NOTICE: You must remove the display assembly before you remove the palm 
    rest; the display hinges pass through the back of the palm rest. 
    3.  Remove the 
    display assembly. 
    4.  Turn the computer over and remove the four M2.5 x 6-mm screws (two scre\
    ws  to each side of the battery bay). 
    Palm-Rest Screws on Bottom of Computer 
    file:///F|/Service%20Manuals/Dell/Latitude/c400/palmrest.htm (1 of 5) \
    [2/28/2004 7:51:03 AM] 
    						
    							Palm Rest : Dell Latitude C400 Service Manual 
     
    1 M2.5 x 6-mm screws (4)
    2 M2.6 x 1.8-mm screws (4)
    3 M2 x 4-mm screws (2)
    4 M2.5 x 6-mm screws (2)
    5.  Remove the four M2.6 x 1.8-mm screws located inside the battery bay. 
    6.  Remove the two M2.5 x 6-mm screws located near the service tag at the ba\
    ck  edge of the computer. 
    7.  Turn the computer over and remove the two M2 x 4-mm screws located above\
      the serial, docking, and video connectors on the back panel. 
    Critical Component Shield 
    file:///F|/Service%20Manuals/Dell/Latitude/c400/palmrest.htm (2 of 5) \
    [2/28/2004 7:51:03 AM] 
    						
    							Palm Rest : Dell Latitude C400 Service Manual 
     
    1 M2 x 4-mm screws (6) (one screw may be captive)
    2 critical component shield
    8.  Remove the six M2 x 4-mm screws (one of which may be captive) that sec\
    ure  the critical component shield to the system board, and lift the shield a\
    way. 
    NOTE: At this point, the memory module under the critical component shield 
    can be replaced. 
    Palm Rest Removal 
    file:///F|/Service%20Manuals/Dell/Latitude/c400/palmrest.htm (3 of 5) \
    [2/28/2004 7:51:03 AM] 
    						
    							Palm Rest : Dell Latitude C400 Service Manual 
     
    1 M2.5 x 6-mm screws (6)
    2 LED cable
    3 palm-rest flex cable
    9.  Remove the six M2.5 x 6-mm screws that secure the palm rest to the syste\
    m  board. 
    10.  Disconnect the LED and palm-rest flex cables. 
    11.  If a Mini PCI wireless card is installed, 
    disconnect the two wireless cables from 
    the card. 
    12.  Lift the palm rest away. 
    file:///F|/Service%20Manuals/Dell/Latitude/c400/palmrest.htm (4 of 5) \
    [2/28/2004 7:51:03 AM] 
    						
    							Palm Rest : Dell Latitude C400 Service Manual 
    Replacing the Palm Rest
    To aid with proper flex cable connection, a white locator line has been \
    added near the 
    ends of the flex cables. When replacing the LED and palm-rest flex cable\
    s, press the 
    cable into the connector until the white line disappears and hold it ste\
    ady while you 
    snap the flex cable connector down. (The white line may reappear after \
    the connector 
    is closed; this should not indicate a problem with the connection.)
    Back to Contents Page
     
     
     
    file:///F|/Service%20Manuals/Dell/Latitude/c400/palmrest.htm (5 of 5) \
    [2/28/2004 7:51:03 AM] 
    						
    							Cooling Fan : Dell Latitude C400 Service Manual 
    Back to Contents Page 
    Cooling Fan 
    Dell™ Latitude™ C400 Service Manual 
      Removing the Cooling Fan
    Removing the Cooling Fan
    NOTICE: Disconnect the computer and any attached devices from electrical 
    outlets, and remove any installed batteries. 
    NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by 
    touching an unpainted metal surface on the computer. 
    NOTICE: Read Preparing to Work Inside the Computer before performing the 
    following procedure. 
    1.  Remove the 
    hard drive. 
    2.  Remove the 
    keyboard. 
    3.  Remove the 
    display assembly. 
    4.  Remove the 
    palm rest. 
    Cooling Fan Removal 
    file:///F|/Service%20Manuals/Dell/Latitude/c400/fan.htm (1 of 3) [2/28\
    /2004 7:51:03 AM] 
    						
    All Dell manuals Comments (0)

    Related Manuals for dell latitude c400 User Manual