Dell Inspiron 8000 Parts Manual

Dell™ Inspiron™ 8000: Removing and Replacing Parts113
The system board’s BIOS contains the system service tag number, which is 
also visible on a bar-code label on the bottom of the computer. The 
replacement kit for the system board assembly includes a floppy disk or CD 
that provides a utility for transferring the service tag number to the 
replacement system board assembly.
 NOTICE: After replacing the microprocessor module, update the BIOS using 
a flash BIOS update program floppy disk or CD that...

114Dell™ Inspiron™ 8000: Removing and Replacing Parts
www.dell.com | support.dell.com 

Dell™ Inspiron™ 8000: Removing and Replacing Parts115
Battery and Media Bay Latch 
Assemblies
 NOTICE: Disconnect the computer and attached devices from electrical 
outlets and remove any installed batteries.
 NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or 
by periodically touching an unpainted metal surface on the computer.
spring
 latch buttons (2)
bottom case assembly location of 
snap tabs (2)
bumps 
wear ribs 
(2 on underside)
slider  

116Dell™ Inspiron™ 8000: Removing and Replacing Parts
www.dell.com | support.dell.com
Removing and Replacing the Battery and Media Bay Latch 
Assemblies
1Follow the instructions in “Preparing to Work Inside the Computer.”
2Remove the keyboard assembly.
3Remove the hinge cover.
4Remove the display assembly.
5Remove the palm rest assembly.
6Remove a latch button from the bottom case assembly by squeezing 
the snap tabs in the center of the latch.
Apply downward pressure to the tabs while squeezing them...

Dell™ Inspiron™ 8000: Removing and Replacing Parts117
Battery Charger Board
 NOTICE: Disconnect the computer and attached devices from electrical 
outlets and remove any installed batteries.
 NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or 
by periodically touching an unpainted metal surface on the computer.
Removing the Battery Charger Board
1Follow the instructions in “Preparing to Work Inside the Computer.”
2Remove the keyboard assembly.
3Remove the hinge cover.
4Remove the...

118Dell™ Inspiron™ 8000: Removing and Replacing Parts
www.dell.com | support.dell.com
Replacing the Battery Charger Board
Align the screw holes on the battery charger board with the screw holes on 
the bottom case assembly, and then press the battery charger board down 
into its connector.
LED Board
 NOTICE: Disconnect the computer and attached devices from electrical 
outlets and remove any installed batteries.
 NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or 
by periodically...

Dell™ Inspiron™ 8000: Removing and Replacing Parts119
Removing the LED Board
1Follow the instructions in “Preparing to Work Inside the Computer.”
2Remove the hinge cover.
3Remove the two M2 x 4-mm screws.
4Pull the LED board away from its connector.
 Replacing the LED Board
1Align the two screw holes with the two mounting holes on the bottom 
case assembly, and press the board into its connector.
2Replace the two M2 x 4-mm screws.
Fan Assembly
 NOTICE: Disconnect the computer and attached devices from...

120Dell™ Inspiron™ 8000: Removing and Replacing Parts
www.dell.com | support.dell.com
Removing the Fan Assembly
1Follow the instructions in “Preparing to Work Inside the Computer.”
2Remove the system board.
3Remove the three M2 x 4-mm screws from the fan assembly.
4Disconnect the two fan cables from the system board.
5Pull the fan assembly away from the back-panel bracket.
 NOTICE: When reconnecting the fan cables, connect the shorter cable to the 
connector closest to the fan assembly. Route both cables...

Dell™ Inspiron™ 8000: Removing and Replacing Parts121
Removing the Protective Covers From the RJ-11 and RJ-45 
Connectors
1 Follow the instructions in “Preparing to Work Inside the Computer.”
2Remove one or b oth o f the plastic  connec tor covers (one o r b oth of the 
covers may be installed) by slipping a nonmarring tool into the cutout 
at the top and pivoting the tool up to disengage the inner securing tab.
To replace a connector cover, orient the cover notch-side-up and snap it into 
the connector...

122Dell™ Inspiron™ 8000: Removing and Replacing Parts
www.dell.com | support.dell.com
Removing the RJ-11/RJ-45 Board
1Follow the instructions in “Preparing to Work Inside the Computer.”
2Remove the system board.
3Remove the M2.5 x 4-mm screw from the RJ-11/RJ-45 board.
 NOTICE: The plastic tab is fragile; pull it back only far enough to remove the 
board assembly.
4
Reach into the enclosure and, while pulling the tall plastic tab away 
from the board assembly to release it, lift out the assembly.
When...