Dell Inspiron 3000 Service Manual
Have a look at the manual Dell Inspiron 3000 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 327 Dell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Removing and Replacing Parts 4-65 13.3-Inch LCD Panel Figure 4-46. 13.3-Inch LCD Panel Removal To remove the 13.3-inch LCD panel, follow these steps: 1. Remove the front bezel. See the previous subsection, “13.3-Inch LCD Front Bezel.” 2. Remove LCD panel screws LC5, LC6, LC7, and LC8. LCD panel LC5 LC8 LC6 LC7 (screws LC5–LC8 are 6 mm) 6 mm back cover LCD-to-inverter cable connector CN2 LCD cable harness inverter cable GS1 (screw GS1 is 3 mm) 3 mm NOTE: The inverter board is installed with the component side down, next to the back cover.
4-66 Dell Inspiron 3000 Series Service Manual 3. Remove the LCD panel. NOTE: Be careful when removing any part of the LCD cable harness. Lift up the LCD panel, and disconnect the LCD cable harness from connec- tor J1 on the back of the LCD panel (for an IBM panel, hold the cable ground strap in place with one hand and peel back the EMI tape covering that holds the ground strap in place on the cable). Disconnect the LCD-to-inverter cable from inverter-board connector CN2 on the side of the inverter board next to the back cover (see Figure 4-47). 4. Remove grounding screw GS1 from the bracket.CAUTION: When reinstalling an IBM LCD cable, slide the cable underneath the ground strap in place and reapply the EMI tape.
Removing and Replacing Parts 4-67 13.3-Inch LCD Inverter Board . Figure 4-47. 13.3-Inch Inverter Board Removal To remove the 13.3-inch inverter board, follow these steps: 1. Remove the front bezel. See “13.3-Inch LCD Front Bezel” found earlier in this section. 2. Remove the LCD panel. See the previous subsection, “13.3-Inch LCD Panel.” 3. Remove the inverter board from the four tabs holdin g it to the back cover. Turn the board over so that the board’s com ponents are facing up. 4. Disconnect the inverter cable from connector CN1 on the inverter board and remove the cable. 5. Remove the inverter board from the back cover. The bracket does not have to be taken off to remove the inverter board. When reinstallin g the inverter board, connect the LCD panel cable to the inverter board connector, CN1, before reinstallin g the bracket. Turn the board over with the com ponents side facing the back cover and secure the board with the tabs. There are four tabs that hold the inverter board in place. The inverter board has locatin g holes in the upper-left corner and lower-right corner. Replace the ta pe on the back of the board. When re placing the inverter board, make sure you have the correct board. The inverter board for a 13.3-inch IBM LCD assembl y is different from the inverter board for a 13.3-inch Samsun g LCD assembly. LCD cable harness inverter cable connector CN1 connector CN2 tabs (4) inverter boardlocating holes (2)
4-68 Dell Inspiron 3000 Series Service Manual 13.3-Inch LCD Hinges Figure 4-48. 13.3-Inch LCD Hinges Removal To remove the 13.3-inch LCD hinges, follow these steps: 1. Remove the front bezel. See “13.3-Inch LCD Front Bezel” found earlier in this section. 2. Place the back cover on a work surface. 3. Remove hinge screws H12, H13, H14, and H15. 4. Remove the hinges from the back cover. The bracket does not have to be taken off to remove the hinges. The bracket in Figure 4-48 is shown removed to assist understanding. The hinges for the 13.3-inch LCD assembly are chromated black and interchangeable. back cover hinges (2) (screws H12–H15 are 5 mm) 5 mm H12 H13 H14 H15
Removing and Replacing Parts 4-69 13.3-Inch LCD Bracket Figure 4-49. 13.3-Inch LCD Bracket Removal To remove the 13.3-inch LCD bracket, follow these steps: 1. Remove the front bezel. See “13.3-Inch LCD Front Bezel” found earlier in this section. 2. Remove the LCD panel. See “13.3-Inch LCD Panel” found earlier in this section. 3. Remove the hinges. See the previous subsection, “13.3-inch LCD Hinges.” 4. Remove the bracket from the back cover. Remove EPE foam (taped in place). Remove bracket screws BR1, BR2, and BR3. Remove the bracket using two plastic wedges. Be careful not to break the plastic case of the back cover or mar the EMI fin- ish on the inside of the cover. back cover bracket EPE foam BR2 BR3 (screws BR1–BR3 are 5 mm) 5 mm BR1 LCD cable harness
4-70 Dell Inspiron 3000 Series Service Manual Start in the lower left corner. Insert a plastic wedge under the bracket and apply pressure upward to free the bracket from the back cover. Insert another plastic wedge one tab at a time along one side of the bezel. Free the bracket from the one corner and this frees the bottom of the bracket. Free the bracket from one side. Repeat the procedure on the other side. Freeing the sides will free the bottom of the bracket. Finally, free the bracket from the top of the bezel. The two top tabs should come free easily. To reinstall the bracket, the LCD cable harness and the inverter board cable must be under the bracket and through the correct channels in the bracket and the back cover. Be careful not to break the hidden plastic tabs when reinstalling the bracket.
Index 1 Index A AC adapter connector, 1-3 removal, 4-4 AC Power indicator, 1-5 assembly, 12.1-inch LCD panel removal, 4-59 assembly, 13.3-inch LCD panel removal, 4-65 audio bezel removal, 4-52 board removal, 4-53 jacks location, 1-3 B base assembly removal, 4-46 battery main, location, 1-3 main, removal, 4-4 secondary, location, 1-3 secondary, removal, 4-8 Battery Activity indicator, 1-5 battery charge gauge, 1-6 Battery Status indicator, 1-5 beep codes during boot routine, 3-1 list of, 3-2 boot routine observing when troubleshooting, 2-3 C Caps Lock indicator, 1-4 CD-ROM drive disassembly, 4-31 location (options bay), 1-3 removal, 4-8 CD-ROM/DVD-ROM/hard-disk drive in- dicator, 1-4 computer features, 1-1 illustrated, 1-3 power, 1-7 power conservation modes, 1-7 technical specifications, 1-9 connector cover, 4-33 connectors location, 1-3 D Dell Diagnostics, 3-4 Diagnostics Menu, 3-5 disassembly procedures, 4-32 diskette drive disassembly, 4-30 location (options bay), 1-3 removal, 4-8 Diskette-Drive Access indicator, 1-5
2 Dell Inspiron 3000 Series Service Manual display close/suspend button, 1-3 latch, 1-3 location, 1-3 DVD-ROM drive disassembly, 4-31 location (options bay), 1-3 removal, 4-8 E eliminating resource conflicts, 2-4 error messages, 3-2, 3-5 ESD, 4-3 expansion connector, 1-3 exploded views 12.1-inch LCD assembly, 4-11 13.3-inch LCD assembly, 4-12 base assembly, 4-14 computer, 4-10 palmrest assembly, 4-13 F factory repair parts and assemblies list of, 4-15 G getting help, 2-5 H hard-disk drive disassembly, 4-29 heat sink removal, 4-42location, 1-3 removal, 4-7 heat sink removal, 4-35 help, 2-5 I I/O connector, illustrated, 1-3 indicator light location, 1-3 infrared board removal, 4-41 feature, 1-2 lens removal, 4-47 port location, 1-3 initial procedures beep codes, 3-1 system error messages, 3-2 troubleshooting, 2-1 initialization error messages, 3-5 Internal Diskette-Drive Access indicator, 1-5 interrupt assignments list of, 1-8 IR board removal, 4-41 IR lens removal, 4-47 K Kensington lock plate removal, 4-56 keyboard location, 1-3 removal, 4-33
Index 3 L latch assembly removal, 4-55 location, 1-3 LCD assembly location, 4-37 removal, 4-37 LCD assembly, 12.1-inch bracket removal, 4-62 front bezel removal, 4-57 hinges removal, 4-61 inverter board removal, 4-60 LCD panel removal, 4-59 LCD assembly, 13.3-inch bracket removal, 4-69 front bezel removal, 4-63 hinges removal, 4-68 inverter board removal, 4-67 LCD panel removal, 4-65 LVDS board removal, 4-49 M main battery location, 1-3 removal, 4-4 main board removal, 4-51 memory maximum configuration, 1-1 system memory, 1-1 memory module capacities supported, 1-1 removal, 4-7 microphone location, 1-3 microprocessor, 1-1 monitor connector, 1-3 N Num Lock indicator, 1-4 O options bay location, 1-3 P Pad Lock indicator, 1-4 palmrest assembly removal, 4-39 parallel connector, 1-3 PC Card cage removal, 4-54 indicator, 1-5 removal, 4-6 slots, 1-3 physical description, 1-3 POST beep codes about, 3-1 list of, 3-2 power button location, 1-3 computer, 1-7 conservation, 1-7 power/suspend indicator, 1-3 precautionary measures, 4-3 processor board removal, 4-48 PS/2 connector, 1-3
4 Dell Inspiron 3000 Series Service Manual R removal and replacement procedures computer orientation, 4-1 precautionary measures, 4-3 recommended tools, 4-1 replicator removing computer from, 4-4 resource conflicts eliminating, 2-4 S save-to-disk suspend mode, 1-8 save-to-RAM suspend mode, 1-7 screws identification and tightening, 4-2 location template, 4-32 Scroll Lock indicator, 1-4 secondary battery location (options bay), 1-3 removal, 4-8 security cable slot, 1-3 serial connector, 1-3 speaker location, 1-3 removal, 4-44 specifications, technical, 1-9 standby mode, 1-7 status display, 1-4 status display panel about, 1-4 location, 1-3 removal, 4-36 subsystems, testing, 3-4 Suspend Mode indicator, 1-4system features, 1-1 overview, 1-1 power, 1-7 system error messages about, 3-2 Dell Diagnostics, 3-4 list of, 3-2 T technical specifications, 1-9 tools recommended replaceable parts and assemblies, 4-1 touch pad assembly removal, 4-43 buttons, 1-3 location, 1-3 troubleshooting boot routine, 2-3 initial procedures, 2-1 initial user contact, 2-1 POST beep codes, 3-1 running the Dell Diagnostics, 3-4 system error messages, 3-2 visual inspection, 2-1 U USB board removal, 4-50 USB connector, 1-3 user contact, initial, 2-1 V visual inspection, 2-1